Study on the tool setting method of micro-milling tool based on in-line holography

Aiming at the various shortcomings of existing tool setting methods, this paper proposes a coaxial holographic tool setting method for tiny tools. Based on the research and analysis of the principle of holographic imaging and the key issues of holographic images, a set of holographic tool setting detection device for micro milling tool was built, and the micro milling tool measurement was carried out on the five-axis machining center using standard tools. experiment. Experimental results show that the tool setting device can efficiently perform tool setting detection of micro-milling tool. Compared with the measurement results of the high-precision external presetting instrument, the relative error of the contact tool setting instrument is 0.033%, and the relative error of the holographic tool setting prototype is 0.007%, which is more effective in realizing the tool setting of tiny tools. Detection. This result verifies the feasibility of the coaxial holographic tool setting method for micro tool, that is, holographic measurement can be used for high-precision tool setting of micro milling tool.

Innovative Use of Wireline Tools Enables Successful Re-Entry on Subsea Wells

Re-entry of subsea wells can always hide unforeseen difficulties. Contingency mobilization of coiled tubing (CT) usually gives a wide spread of solutions to overcome most of the possible events. However, when operating on a winterized semisubmersible rig in the remote fields of the Barents Sea, rig-up of CT spread can be costly and complicated. Furthermore, lighter and easily deployable wireline powered mechanical tools have proven to be effective in tackling most of the possible challenges. Possible tubing obstruction issues can be resolved via clean-out/suction, pumping, or milling methods. In this instance, all three were used with different tools to clear the obstruction from the tubing and to clean with precision inside an internal fishing profile of a well head barrier plug to allow for well access. The first challenge encountered when re-entering the tubing in Well-1 was the presence of a 151m long hydrate plug. It was easily removed by an e-line tool capable of applying 10 bar of dynamic underbalance, while maintaining a continuous flow circulation. Such an application is a novel development in the use of existing tools. After removing the hydrate plug, it was discovered that the tubing was plugged by 246m of wax deposits, which were preventing communication with the reservoir. To overcome this problem, a jetting tool was utilized to continuously pump fresh wax solvent inside the landing string. Pumping continuously fresh wax dissolvent provided a unique and effective means to mechanically and chemically remove a significant obstruction. Once the communication with the reservoir was re-established, an additional obstruction of almost 129m (resistant to the wax dissolvent) was encountered. To overcome this challenge an e-line milling tool was utilized, and the resulting debris was bullheaded down into the reservoir. Similarly, when re-entering Well-2 a challenge was encountered to pull a barrier plug due to debris deposits inside the internal fishing profile. Both e-line milling and suction tools were sequentially used to resolve the problem and prepare the plug for retrieval. The tools used were already available on the market for different applications. In this case the tools were used in an alternative way, using their features to solve issues beyond conventional expectations. The result fosters confidence to plan future re-entry without the need for mobilizing a CT spread.

Structure and Content Analysis of Raw Materials for Production of Trimanganese Tetraoxide Pigment

The research aims to reveal the structure, phase, and elemental content of manganese ores from deposits—Bogach (Karaganda region, Kazakhstan) and Zhaksy (Akmola region, Kazakhstan). The samples were studied with scanning electron microscopy with energy dispersive analysis (SEM-EDA), X-ray diffractometry (XRD), Infra-red spectroscopy (IRS). During the research, structural peculiarities, elemental and phase content of the samples have been revealed. The mineral matter of the Bogach deposit ore mainly consists of hollandite, cryptomelane, braunite, calcite, bixbyite, quartz. The Zhaksy deposit ore includes quartz, hollandite, bixbyite, pyrolusite. Bogach ore includes (wt.%) C(10.68), O(32.00), Mn(43.26), Ca(6.36), Si(3.51), Na(0.52), Al(1.13), Mg(0.69), K(1.85). The elemental content of Mn in Zhaksy ore is two times lower. Zhaksy ore includes (wt.%) C(23.77), O(32.1), Mn(21.81), Si(10.52), Al(5.13), K(1.21), Fe(5.47). The obtained data of the conducted spectral analysis indicate that both samples represent a polymineral heterogeneous structure. Conducted research allows to conclude, that by phase-elemental content the Bogach ore can be used for obtaining trimanganese tetraoxide pigment similar to manganese ores from West Sumatera deposit (Indonesia) by top-down method using grinding with a milling tool and high-temperature sintering.

Trochoidal Milling Path with Variable Feed. Application to the Machining of a Ti-6Al-4V Part

Trochoidal milling is a well-stablished machining strategy which still allows for the introduction of new approaches. This strategy can be applied to any kind of material, although it is usually associated to advanced materials, such as titanium and nickel alloys. This study is based on the adaptation of the feed speed of a milling tool with Ti-6Al-4V, so the chip width can be maintained constant without modifying the path geometry. A singularity in the experimental stage was to mill an Archimedes spiral groove instead of the conventional straight grooves. This made it possible to obtain a concave wall as well as a convex one and to optimize the amount of material used. The time efficiency compared to a constant feed, was slightly superior to 20%, reducing tool wear also. These techniques require milling machines with high mechanical and kinematic performance, as well as the absence of clearance between joints and a high acceleration capacity.

Vibration-based tool life monitoring for ceramics micro-cutting under various toolpath strategies

The 21st century manufacturing technology is unimagined without the various CAM (Computer Aided Manufacturing) toolpath generation programs. The aims of developing the toolpath strategies which are offered by the cutting control software is to ensure the longest possible tool lifetime and high efficiency of the cutting method. In this paper, the goal is to compare the efficiency of the 3 types of tool path strategies in the very special field of micro-milling of ceramic materials. The dimensional distortion of the manufactured geometries served to draw the Taylor curve for describing the wearing progress of the cutting tool helping to determine the worn-in, normal and wear out stages. These isolations allow to separate the connected high-frequency vibration measurements as well. Applying the novel feature selection technique of the authors, the basis for the vibration based micro-milling tool condition monitoring for ceramics cutting is presented for different toolpath strategies. It resulted in the identification of the most relevant vibration signal features and the presentation of the identified and automatically separated tool wearing stages as well.

An Experimental Evaluation of Particle Impact Dampers Applied on the Tool for Milling of Hardened Steel Complex Surface

In the manufacturing of dies and molds, vibrations may represent serious problems, since the finishing tool used is usually slender (high Length / Diameter ratio) in order to machine deep cavities with complex geometry, typical of these products. Vibration is an undesirable phenomenon in any machining operation as it can lead to poor surface finish, lower material removal rate and increased tool wear. The use of impact dampers in the tool has proven to be an effective method for reducing vibration in machining processes. Damping occurs through energy dissipation and linear momentum exchange during intermittent collisions between the main structure (in this case the milling tool) and a free mass (spheres or cylinders placed within a tool cavity). Although efficient, these types of dampers are highly nonlinear. Thus, the aim of this work is to analyze the effect of different materials and geometries (steel spheres, tungsten spheres and steel cylinders) acting as impact dampers inside a ball nose end milling tool. To do so, milling of a convex D6 steel surface was performed, comparing commercial tool holders with dampened ones. The results showed that the tools with impact dampers generated lower values of roughness in the workpiece (around 30% of the value observed in the conventional steel tool holder for the case of steel cylinders and around 40% for both spheres) and presented lower levels of vibration when compared to the same tool without the impact damper, mainly in the machining of workpiece regions where radial and tangential forces are predominant. The tool which used tungsten spheres generated roughness surfaces similar to those obtained with steel spheres, while the tool that used steel cylinders only generated lower roughness in the regions where the axial force component is not predominant, which shows that their performance is highly dependent on the resulting force direction.

Experimental Study on Fabrication of CVD Diamond Micro Milling Tool by Picosecond Pulsed Laser

Because of the many advantages of high-precision micromachining, picosecond pulsed lasers (PSPLs) can be used to process chemical-vapor-deposited diamonds (CVD-D). With the appropriate PSPL manufacturing technique, sharp and smooth edges of CVD-D micro tools can be generated. In this study, a PSPL is used to cut CVD-D. To optimize PSPL cutting, the effects of its parameters including fluence, pulse pitch, and wavelength on the cutting results were investigated. The results showed that the wavelength had the greatest impact on the sharpness of CVD-D. With PSPL cutting, sharp cutting edges, and smooth fabricated surfaces of the CVD-D, micro tools were achieved. Finally, the fabrication of CVD-D micro milling tools and micro milling experiments were also demonstrated.