Titanium Trisulfide Nanoribbons Affect the Downy Birch and Poplar × Aspen Hybrid in Plant Tissue Culture via the Emission of Hydrogen Sulfide

Plant tissue culture is an important tool for accelerated vegetative reproduction of woody plants. To increase the efficiency of this method, it is necessary to search for new growth stimulators and protectors of microshoots. Two-dimensional (2D) nanomaterials are highly promising for applications in medicine and biotechnologies. We have studied the effects of TiS3 nanoribbons with the following mean dimensions: thickness less than 100 nm, length 1–10 μm and width 0.4–1 μm upon poplar × aspen hybrid and downy birch microclones in plant tissue culture. We have found the effectiveness of this particular nanomaterial as a sterilizing and stimulating agent in the initial growth stage and as a rhizogenesis-activating agent in the rooting stage. We analyzed a wide range of TiS3 concentrations in the nutrient media and identified 1.5 and 3 μg/L as optimal. However, concentration-dependent toxic effects manifesting themselves through microclones viability suppression have been discovered in the groups exposed to 6 and 15 μg/L TiS3. We have established that plant reaction to TiS3 treatment is specific for different plant species, i.e., downy birch is generally more tolerant than poplar × aspen hybrid. Here, we propose that the protective and stimulating effects of titanium trisulfide as well as its toxicity in high concentrations can be explained by the release of hydrogen sulfide as a result of aqueous hydrolysis of nanoribbons and its effect on plants. Additional studies are required in order to assess all biological effects produced by TiS3 nanoribbons at further stages of ontogenetic development and to identify the mechanisms of their action.

Tunable Photodetectors via In Situ Thermal Conversion of TiS3 to TiO2

In two-dimensional materials research, oxidation is usually considered as a common source for the degradation of electronic and optoelectronic devices or even device failure. However, in some cases a controlled oxidation can open the possibility to widely tune the band structure of 2D materials. In particular, we demonstrate the controlled oxidation of titanium trisulfide (TiS3), a layered semicon-ductor that has attracted much attention recently thanks to its quasi-1D electronic and optoelectron-ic properties and its direct bandgap of 1.1 eV. Heating TiS3 in air above 300 °C gradually converts it into TiO2, a semiconductor with a wide bandgap of 3.2 eV with applications in photo-electrochemistry and catalysis. In this work, we investigate the controlled thermal oxidation of indi-vidual TiS3 nanoribbons and its influence on the optoelectronic properties of TiS3-based photodetec-tors. We observe a step-wise change in the cut-off wavelength from its pristine value ~1000 nm to 450 nm after subjecting the TiS3 devices to subsequent thermal treatment cycles. Ab-initio and many-body calculations confirm an increase in the bandgap of titanium oxysulfide (TiO2-xSx) when in-creasing the amount of oxygen and reducing the amount of sulfur.

Tunable Photodetectors via in Situ Thermal Conversion of TiS3 to TiO2

In two-dimensional materials research, oxidation is usually considered as a common source for the degradation of electronic and optoelectronic devices or even device failure. However, in some cases a controlled oxidation can open the possibility to widely tune the band structure of 2D materials. In particular, we demonstrate the controlled oxidation of titanium trisulfide (TiS3), a layered semiconductor that attracted much attention recently thanks to its quasi-1D electronic and optoelectronic properties and its direct bandgap of 1.1 eV. Heating TiS3 in air above 300 °C gradually converts it into TiO2, a semiconductor with a wide bandgap of 3.2 eV with applications in photo-electrochemistry and catalysis. In this work, we investigate the controlled thermal oxidation of individual TiS3 nanoribbons and its influence on the optoelectronic properties of TiS3-based photodetectors. We observe a step-wise change in the cut-off wavelength from its pristine value ~1000 nm to 450 nm after subjecting the TiS3 devices to subsequent thermal treatment cycles. Ab-initio and many-body calculations confirm an increase of the bandgap of titanium oxysulfide (TiO2-xSx) when increasing the amount of oxygen and reducing the amount of sulfur.