Joining SI3 N4 to an Iron Aluminide Alloy Using Soft Interlayers

2012 ◽  
pp. 121-134
Author(s):  
M. Brochu ◽  
R. A. L. Drew ◽  
M. D. Pugh
Keyword(s):  
Iron Aluminide

ALCHEMI of B2-Ordered Fe50Al45Me5 alloys

1996 ◽  
Vol 54 ◽  
pp. 548-549
Author(s):  
Ian M. Anderson
Keyword(s):  
Room Temperature ◽  
Iron Aluminide ◽  
Low Density ◽  
Intermetallic Alloys ◽  
Practical Applications ◽  
Alloying Additions ◽  
Site Distribution ◽  
Good Corrosion Resistance ◽  
Room Temperature Ductility ◽  
The Matrix

B2-ordered iron aluminide intermetallic alloys exhibit a combination of attractive properties such as low density and good corrosion resistance. However, the practical applications of these alloys are limited by their poor fracture toughness and low room temperature ductility. One current strategy for overcoming these undesirable properties is to attempt to modify the basic chemistry of the materials with alloying additions. These changes in the chemistry of the material cannot be fully understood without a knowledge of the site-distribution of the alloying elements. In this paper, the site-distributions of a series of 3d-transition metal alloying additions in B2-ordered iron aluminides are studied with ALCHEMI.A series of seven alloys of stoichiometry Fe50AL45Me5, with Me = {Ti, V, Cr, Mn, Co, Ni, Cu}, were prepared with identical heating cycles. Microalloying additions of 0.2% B and 0.1% Zr were also incorporated to strengthen the grain boundaries, but these alloying additions have little influence on the matrix chemistry and are incidental to this study.

Sintering Behavior of Iron Aluminide Powders

2003 ◽  
Vol 426-432 ◽  
pp. 1897-1902
Author(s):  
S. Gedevanishvili ◽  
S.C. Deevi
Keyword(s):  
Iron Aluminide ◽  
Sintering Behavior

Study of the Role of Small Additions of Zr in the CVD- FBR Aluminization Process

2009 ◽  
Vol 289-292 ◽  
pp. 293-300
Author(s):  
L. Sánchez ◽  
F.J. Bolívar ◽  
M.P. Hierro ◽  
F.J. Pérez
Keyword(s):  
Fluidized Bed ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Fluidized Bed Reactor ◽  
Iron Aluminide ◽  
Martensitic Steels ◽  
Aluminide Coatings ◽  
Deposition Parameters ◽  
Zirconium Powder

In this work, iron aluminide coatings were developed by Chemical Vapor Deposition in Fluidized Bed Reactor (CVD-FBR) on ferritic-martensitic steels. Small additions of zirconium powder were introduced in the fluidized bed; as a consequence, the obtained coatings are thicker than that without zirconium additions. When Zr powders are added in the fluidized bed, the deposition atmosphere drastically changes, leading to increase the deposition rate. Thermodynamic calculations were carried out to simulate the modifications in the CVD atmosphere in the Al/Zr deposition system in comparison to the single aluminization. In order to optimize the conditions of the deposition, parameters such as temperature and concentration of zirconium introduced into the bed were evaluated and compared with the results obtained for the single aluminum deposition.

Study of an iron-aluminide and alumina tritium barrier coating

2011 ◽  
Vol 417 (1-3) ◽  
pp. 1237-1240 ◽  
Author(s):  
H.G. Yang ◽  
Q. Zhan ◽  
W.W. Zhao ◽  
X.M. Yuan ◽  
Y. Hu ◽  
...  
Keyword(s):  
Iron Aluminide ◽  
Barrier Coating

Study on formation and characterization of iron aluminide coatings on 9Cr–1Mo steel substrate

2014 ◽  
Vol 240 ◽  
pp. 365-372 ◽  
Author(s):  
R. Arabi Jeshvaghani ◽  
M. Emami ◽  
O. Shafiee ◽  
H.R. Shahverdi
Keyword(s):  
Steel Substrate ◽  
Iron Aluminide ◽  
Aluminide Coatings

Electrochemical Studies on High-Temperature Corrosion of Silicon-Iron Coatings and Iron Aluminide Intermetallic Alloys by Molten Salts

CORROSION ◽  
2001 ◽  
Vol 57 (6) ◽  
pp. 489-496 ◽  
Author(s):  
M. Amaya ◽  
J. Porcayo-Calderon ◽  
L. Martinez
Keyword(s):  
High Temperature ◽  
Molten Salt ◽  
Electric Power ◽  
Molten Salts ◽  
Corrosion Current ◽  
High Temperature Corrosion ◽  
Iron Aluminide ◽  
Fuel Oil ◽  
Silicon Iron ◽  
Salt Corrosion

Abstract The performance of Fe-Si coatings and an iron aluminide (FeAl) intermetallic alloy (FeAl40at%+0.1at%B+10vol%Al2O3) in molten salts containing vanadium pentoxide (V2O5) and sodium sulfate (Na2SO4) is reported. Corrosion and fouling by ash deposits containing V2O5 and Na2SO4 are typical corrosion problems in fuel oil-fired electric power units. High-temperature corrosion tests were performed using both electrochemical polarization and immersion techniques. The temperature interval of this study was 600°C to 900°C, and the molten salts were 80wt%V2O5-20wt%Na2SO4. Curves of corrosion current density vs temperature obtained by the potentiodynamic studies are reported, as well as the weight loss vs temperature curves from molten salt immersion tests. Both Fe-Si coatings and FeAl40at%+0.1at%B+10vol%Al2O3 showed good behavior against molten salt corrosion. The final results show the potential of these coatings and alloys to solve the high-temperature corrosion in fuel oil-fired electric power units.

Sign in / Sign up

Export Citation Format

Share Document