A Reconfigurable 6-DoF Cable-Driven Parallel Robot with an Extended Rotational Workspace

2021 ◽  
pp. 322-331
Author(s):  
Ferdaws Ennaiem ◽  
Abdelbadiâ Chaker ◽  
Med Amine Laribi ◽  
Juan Sandoval ◽  
Sami Bennour ◽  
...  
Keyword(s):  
Parallel Robot

scholarly journals Sensitivity Based Selection of an Optimal Cable-Driven Parallel Robot Design for Rehabilitation Purposes

Robotics ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 7
Author(s):  
Ferdaws Ennaiem ◽  
Abdelbadiâ Chaker ◽  
Juan Sebastián Sandoval Arévalo ◽  
Med Amine Laribi ◽  
Sami Bennour ◽  
...  
Keyword(s):  
Pareto Front ◽  
Parallel Robot ◽  
Elastic Stiffness ◽  
Upper Limb Rehabilitation ◽  
Daily Life Activities ◽  
System A ◽  
The Monte Carlo Method ◽  
Genetic Algorithm Method ◽  
Limb Rehabilitation ◽  
Selection Of

This paper deals with the design of an optimal cable-driven parallel robot (CDPR) for upper limb rehabilitation. The robot’s prescribed workspace is identified with the help of an occupational therapist based on three selected daily life activities, which are tracked using a Qualisys motion capture system. A preliminary architecture of the robot is proposed based on the analysis of the tracked trajectories of all the activities. A multi-objective optimization process using the genetic algorithm method is then performed, where the cable tensions and the robot size are selected as the objective functions to be minimized. The cables tensions are bounded between two limits, where the lower limit ensures a positive tension in the cables at all times and the upper limit represents the maximum torque of the motor. A sensitivity analysis is then performed using the Monte Carlo method to yield the optimal design selected out of the non-dominated solutions, forming the obtained Pareto front. The robot with the highest robustness toward the disturbances is identified, and its dexterity and elastic stiffness are calculated to investigate its performance.

scholarly journals Social spider optimization algorithm for tuning parameters in PD-like Interval Type-2 Fuzzy Logic Controller applied to a parallel robot

2021 ◽  
Vol 54 (3-4) ◽  
pp. 303-323
Author(s):  
Amjad J Humaidi ◽  
Huda T Najem ◽  
Ayad Q Al-Dujaili ◽  
Daniel A Pereira ◽  
Ibraheem Kasim Ibraheem ◽  
...  
Keyword(s):  
Fuzzy Logic ◽  
Trajectory Tracking ◽  
Fuzzy Logic Controller ◽  
Optimization Technique ◽  
Parallel Robot ◽  
Design Parameters ◽  
Social Spider ◽  
Social Spider Optimization ◽  
Interval Type

This paper presents control design based on an Interval Type-2 Fuzzy Logic (IT2FL) for the trajectory tracking of 3-RRR (3-Revolute-Revolute-Revolute) planar parallel robot. The design of Type-1 Fuzzy Logic Controller (T1FLC) is also considered for the purpose of comparison with the IT2FLC in terms of robustness and trajectory tracking characteristics. The scaling factors in the output and input of T1FL and IT2FL controllers play a vital role in improving the performance of the closed-loop system. However, using trial-and-error procedure for tuning these design parameters is exhaustive and hence an optimization technique is applied to achieve their optimal values and to reach an improved performance. In this study, Social Spider Optimization (SSO) algorithm is proposed as a useful tool to tune the parameters of proportional-derivative (PD) versions of both IT2FLC and T1FLC. Two scenarios, based on two square desired trajectories (with and without disturbance), have been tested to evaluate the tracking performance and robustness characteristics of proposed controllers. The effectiveness of controllers have been verified via numerical simulations based on MATLAB/SIMULINK programming software, which showed the superior of IT2FLC in terms of robustness and tracking errors.

scholarly journals Sliding Mode Robust Control of a Wire-Driven Parallel Robot Based on HJI Theory and a Disturbance Observer

IEEE Access ◽  
2020 ◽  
Vol 8 ◽  
pp. 215235-215245
Author(s):  
Yuqi Wang ◽  
Qi Lin ◽  
Jiacai Huang ◽  
Lei Zhou ◽  
Jinjiang Cao ◽  
...  
Keyword(s):  
Robust Control ◽  
Disturbance Observer ◽  
Sliding Mode ◽  
Parallel Robot

A PD Computed Torque Control Method with Online Self-gain Tuning for a 3UPS-PS Parallel Robot

Robotica ◽  
2021 ◽  
pp. 1-13
Author(s):  
Xiaogang Song ◽  
Yongjie Zhao ◽  
Chengwei Chen ◽  
Liang’an Zhang ◽  
Xinjian Lu
Keyword(s):  
Feedback Loop ◽  
Control Method ◽  
Virtual Work ◽  
Parallel Robot ◽  
Torque Control ◽  
Virtual Work Principle ◽  
Tuning Method ◽  
Computed Torque Control ◽  
Control Feedback ◽  
Computed Torque

SUMMARY In this paper, an online self-gain tuning method of a PD computed torque control (CTC) is used for a 3UPS-PS parallel robot. The CTC is applied to the 3UPS-PS parallel robot based on the robot dynamic model which is established via a virtual work principle. The control system of the robot comprises a nonlinear feed-forward loop and a PD control feedback loop. To implement real-time online self-gain tuning, an adjustment method based on the genetic algorithm (GA) is proposed. Compared with the traditional CTC, the simulation results indicate that the control algorithm proposed in this study can not only enhance the anti-interference ability of the system but also improve the trajectory tracking speed and the accuracy of the 3UPS-PS parallel robot.

Sign in / Sign up

Export Citation Format

Share Document