Numerical Investigation on the Effect of Reinforcement Shear Connectors in Load Bearing Capacity of Partially Encased Composite Beams

2022 ◽  
pp. 82-98
Author(s):  
Tamirat Semu ◽  
Temesgen Wondimu ◽  
Belay Worku
Keyword(s):  
Bearing Capacity ◽  
Numerical Investigation ◽  
Composite Beams ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Shear Connectors

scholarly journals An Analysis of the Load-Bearing Capacity of Timber-Concrete Composite Beams with Profiled Sheeting

2017 ◽  
Vol 27 (4) ◽  
pp. 143-156 ◽  
Author(s):  
Maciej Szumigała ◽  
Ewa Szumigała ◽  
Łukasz Polus
Keyword(s):  
Numerical Analysis ◽  
Bearing Capacity ◽  
Concrete Slab ◽  
Composite Beams ◽  
Concrete Slabs ◽  
Timber Beam ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Shear Connectors ◽  
Timber Beams

Abstract This paper presents an analysis of timber-concrete composite beams. Said composite beams consist of rectangular timber beams and concrete slabs poured into the steel sheeting. The concrete slab is connected with the timber beam using special shear connectors. The authors of this article are trying to patent these connectors. The article contains results from a numerical analysis. It is demonstrated that the type of steel sheeting used as a lost formwork has an influence on the load-bearing capacity and stiffness of the timber-concrete composite beams.

scholarly journals Numerical Modelling Of The Strengthening Process Of Steel-Concrete Composite Beams

2015 ◽  
Vol 19 (4) ◽  
pp. 99-110 ◽  
Author(s):  
Piotr Szewczyk ◽  
Maciej Szumigała
Keyword(s):  
Numerical Modelling ◽  
Bearing Capacity ◽  
Composite Beam ◽  
Steel Plate ◽  
Composite Beams ◽  
Steel Beam ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Main Assumption ◽  
The Cost

Abstract This paper presents the numerical modelling of strengthening a steel-concrete composite beam. The main assumption is that the strengthening is not the effect of the state of a failure of a structure, but it resulted from the need to increase the load-bearing capacity and stiffness of the structure (for example: due to a change in the use of the object). The expected solution is strengthening without the necessity to completely unload the structures (to reduce the scope of works, the cost of modernization and to shorten the time). The problem is presented on the example of a composite beam which was strengthened through welding a steel plate to the lower flange of the steel beam. The paper describes how energy parameters are used to evaluate the efficiency of structures’ strengthening and proposes an appropriate solution.

scholarly journals Numerical evaluation of the plastic hinges developed in headed stud shear connectors in composite beams with profiled steel sheeting

2018 ◽  
Author(s):  
Valentino Vigneri ◽  
Christoph Odenbreit ◽  
Matthias Braun
Keyword(s):  
Bearing Capacity ◽  
Numerical Evaluation ◽  
Composite Beams ◽  
Shear Capacity ◽  
Embedment Depth ◽  
Shear Connector ◽  
Load Bearing Capacity ◽  
Plastic Hinges ◽  
Load Bearing ◽  
Headed Stud

For composite beams using novel steel sheeting, the current Eurocode 4 rules sometimes overestimate the load bearing capacity of the shear connector. This is due to the larger rib heights and the smaller rib widths in comparison with the old studies, which have been carried out to calibrate the current design equations. The RFCS Project “DISCCO” investigated this phenomena and the working group under mandate M515, CEN/TC250/SC4/SC4.T3 is enhancing this equation and working on a proposal to be taken over in the new version of Eurocode 4.The proposed new equation covers the failure behaviour of the shear connection more in detail. The test results show, that the failure consists in a combined concrete cone and stud in bending. Due to the geometry of novel steel sheeting, the load bearing capacity of the headed stud shear connector is no more limited by its shear capacity, but by its bending capacity.A 3D non-linear finite element model is developed and validated through the support of the DISCCO push-out tests. A good agreement between numerical and experimental results in terms of force-slip behaviour is achieved. Special attention of this work lies on the numerical evaluation of the number of plastic hinges ny: a stress-based procedure is presented and the results are compared to the equations presented for new Eurocode 4.The numerical simulations show that the upper plastic hinge moves up as the slip increases due to the progressive crushing of the concrete in the rib. From the parametric study, it turns out that ny is linearly proportional to the embedment depth. Compared to pre-punched hole decking, through-deck welding specimen activates less plastic hinges in the studs because of the higher stiffness provided at the base of the stud.

scholarly journals Preliminary Analysis of the Aluminiumtimber Composite Beams

2017 ◽  
Vol 27 (4) ◽  
pp. 131-141 ◽  
Author(s):  
Maciej Szumigała ◽  
Marcin Chybiński ◽  
Łukasz Polus
Keyword(s):  
Bearing Capacity ◽  
Aluminium Alloys ◽  
Composite Structures ◽  
Preliminary Analysis ◽  
Composite Beams ◽  
High Price ◽  
Timber Beam ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
New Type

Abstract This paper presents a new type of composite structures - aluminium-timber beams. These structures have an advantage over other existing composite structures, because they are lighter. However, their application may be limited due to the high price of aluminium alloys. The authors of this article made an attempt to calculate the load-bearing capacity of an aluminium-timber beam.

TIMBER-CONCRETE COMPOSITE-A HIGH-EFFICIENT AND SUSTAINABLE CONSTRUCTION METHOD

2021 ◽  
Vol 8 (1) ◽  
Author(s):  
Klaus Holschemacher
Keyword(s):  
Reinforced Concrete ◽  
Bearing Capacity ◽  
High Efficiency ◽  
Concrete Slab ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Shear Connectors ◽  
Reinforced Concrete Slabs ◽  
High Efficient ◽  
Timber Beams

Timber-concrete composite (TCC) is a well-tried building method for construction of sustainable and robust floor systems with high load-bearing capacity. TCC sections consist of timber beams linked by shear connectors with a plain or reinforced concrete slab. Usually, by the shear connectors only flexible bond between the timber beams and the concrete slab may be provided. Nevertheless, TCC slabs have high flexural stiffness and appropriate load-bearing capacity enabling their application in residential and office buildings, and even in bridge construction. The paper reports state-of-the-art and recent developments in design and construction of TCC slabs. Especially, in the context of revaluation and strengthening of existing timber-beam ceilings it is a widely accepted technique today. But also, in design of new buildings, TCC slabs are an advantageous solution because of their reduced environmental impact in contrast to traditional reinforced concrete slabs. By many examples in recent design practice the high efficiency of TCC systems was proved.

Increased load bearing capacity of mechanically joined FRP/metal joints using a pin structured auxiliary joining element

2020 ◽  
Vol 62 (1) ◽  
pp. 55-60
Author(s):  
Per Heyser ◽  
Vadim Sartisson ◽  
Gerson Meschut ◽  
Marcel Droß ◽  
Klaus Dröder
Keyword(s):  
Bearing Capacity ◽  
Load Bearing Capacity ◽  
Load Bearing

Load-Bearing Capacity of Direct Inlay-Retained Fibre-reinforced Composite Fixed Partial Dentures with Different Cross-Sectional Pontic Design

2017 ◽  
Vol 68 (1) ◽  
pp. 94-100
Author(s):  
Oana Tanculescu ◽  
Adrian Doloca ◽  
Raluca Maria Vieriu ◽  
Florentina Mocanu ◽  
Gabriela Ifteni ◽  
...  
Keyword(s):  
Bearing Capacity ◽  
Fracture Pattern ◽  
Load Bearing Capacity ◽  
Cross Sectional ◽  
Load Bearing ◽  
Reinforced Composite ◽  
Polyethylene Fibre

The load-bearing capacity and fracture pattern of direct inlay-retained FRC FDPs with two different cross-sectional designs of the ponticwere tested. The aim of the study was to evaluate a new fibre disposition. Two types of composites, Filtek Bulk Fill Posterior Restorative and Filtek Z250 (3M/ESPE, St. Paul, MN, USA), and one braided polyethylene fibre, Construct (Kerr, USA) were used. The results of the study suggested that the new tested disposition of the fibres prevented in some extend the delamination of the composite on buccal and facial sides of the pontic and increased the load-bearing capacity of the bridges.

Sign in / Sign up

Export Citation Format

Share Document