Influence of 5-axes-kinematics Geometrical Accuracy in Riblet Manufacturing Processes

2013 ◽  
pp. 69-74 ◽  
Author(s):  
Berend Denkena ◽  
Jens Köhler ◽  
Thomas Krawczyk
Keyword(s):  
Manufacturing Processes ◽  
Geometrical Accuracy

Impact of fiber structure on edge-wicking of highly-sized paperboard

TAPPI Journal ◽  
2018 ◽  
Vol 17 (08) ◽  
pp. 437-443
Author(s):  
Lebo Xu ◽  
Jeremy Meyers ◽  
Peter Hart
Keyword(s):  
Fiber Surface ◽  
Manufacturing Processes ◽  
Paper Machine ◽  
Liquid Penetration ◽  
Fiber Structure ◽  
Cut Edge ◽  
Local Fiber

Coffee edge-wicking testing was conducted on two groups of highly-sized paperboard manufactured at two mills with similar manufacturing processes, but with vastly different local fiber sources. Although the Hercules size test (HST) indicated similar internal size levels between the two types of board, the edge-wicking behavior was noticeably different. Analysis of fiber structure revealed that the board with more edge-wicking had fibers with thicker fiber walls, which kept the fiber lumen more open after pressing and drying on a paper machine. It was demonstrated that liquid penetration through voids between fibers in highly-sized paperboard was limited, because the fiber surface was well protected by the presence of sufficient sizing agent. Nevertheless, freshly exposed fiber walls and lumens at the cut edge of the sheet were not protected by sizing material, which facilitated edge-wicking. The correlation between fiber structure and edge-wicking behavior was highlighted in this work to inspire development of novel sizing strategies that protect the freshly cut edge of the sheet from edge-wicking.

An Overview of 300 mm SOI Starting Wafer Quality and Its Yield Detractors

2005 ◽  
Author(s):  
Pei Y. Tsai ◽  
Junedong Lee ◽  
Paul Ronsheim ◽  
Lindsay Burns ◽  
Richard Murphy ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
Device Fabrication ◽  
Sampling Plan ◽  
Silicon On Insulator ◽  
Manufacturing Processes ◽  
Circuit Performance ◽  
Characterization Techniques ◽  
Wafer Manufacturing

Abstract A stringent sampling plan is developed to monitor and improve the quality of 300mm SOI (silicon on insulator) starting wafers procured from the suppliers. The ultimate goal is to obtain the defect free wafers for device fabrication and increase yield and circuit performance of the semiconductor integrated circuits. This paper presents various characterization techniques for QC monitor and examples of the typical defects attributed to wafer manufacturing processes.

Towards High Accuracy Fault Diagnosis of Digital Circuits

2004 ◽  
Author(s):  
Camelia Hora ◽  
Stefan Eichenberger
Keyword(s):  
Fault Diagnosis ◽  
Fault Location ◽  
Digital Circuits ◽  
High Accuracy ◽  
Manufacturing Processes ◽  
Diagnosis Method ◽  
Technology Trend

Abstract Due to the development of smaller and denser manufacturing processes most of the hardware localization techniques cannot keep up satisfactorily with the technology trend. There is an increased need in precise and accurate software based diagnosis tools to help identify the fault location. This paper describes the software based fault diagnosis method used within Philips, focusing on the features developed to increase its accuracy.

Geometrical accuracy of the Novalis stereotactic radiosurgery system for trigeminal neuralgia

2004 ◽  
Vol 101 (Supplement3) ◽  
pp. 351-355 ◽  
Author(s):  
Javad Rahimian ◽  
Joseph C. Chen ◽  
Ajay A. Rao ◽  
Michael R. Girvigian ◽  
Michael J. Miller ◽  
...  
Keyword(s):  
Quality Assurance ◽  
Trigeminal Neuralgia ◽  
Image Fusion ◽  
Stereotactic Radiosurgery ◽  
Ct Images ◽  
Radiochromic Film ◽  
Quality Assurance Program ◽  
Content Type ◽  
Geometrical Accuracy ◽  
Fine Print

Object. Stringent geometrical accuracy and precision are required in the stereotactic radiosurgical treatment of patients. Accurate targeting is especially important when treating a patient in a single fraction of a very high radiation dose (90 Gy) to a small target such as that used in the treatment of trigeminal neuralgia (3 to 4—mm diameter). The purpose of this study was to determine the inaccuracies in each step of the procedure including imaging, fusion, treatment planning, and finally the treatment. The authors implemented a detailed quality-assurance program. Methods. Overall geometrical accuracy of the Novalis stereotactic system was evaluated using a Radionics Geometric Phantom Chamber. The phantom has several magnetic resonance (MR) and computerized tomography (CT) imaging—friendly objects of various shapes and sizes. Axial 1-mm-thick MR and CT images of the phantom were acquired using a T1-weighted three-dimensional spoiled gradient recalled pulse sequence and the CT scanning protocols used clinically in patients. The absolute errors due to MR image distortion, CT scan resolution, and the image fusion inaccuracies were measured knowing the exact physical dimensions of the objects in the phantom. The isocentric accuracy of the Novalis gantry and the patient support system was measured using the Winston—Lutz test. Because inaccuracies are cumulative, to calculate the system's overall spatial accuracy, the root mean square (RMS) of all the errors was calculated. To validate the accuracy of the technique, a 1.5-mm-diameter spherical marker taped on top of a radiochromic film was fixed parallel to the x–z plane of the stereotactic coordinate system inside the phantom. The marker was defined as a target on the CT images, and seven noncoplanar circular arcs were used to treat the target on the film. The calculated system RMS value was then correlated with the position of the target and the highest density on the radiochromic film. The mean spatial errors due to image fusion and MR imaging were 0.41 ± 0.3 and 0.22 ± 0.1 mm, respectively. Gantry and couch isocentricities were 0.3 ± 0.1 and 0.6 ± 0.15 mm, respectively. The system overall RMS values were 0.9 and 0.6 mm with and without the couch errors included, respectively (isocenter variations due to couch rotation are microadjusted between couch positions). The positional verification of the marker was within 0.7 ± 0.1 mm of the highest optical density on the radiochromic film, correlating well with the system's overall RMS value. The overall mean system deviation was 0.32 ± 0.42 mm. Conclusions. The highest spatial errors were caused by image fusion and gantry rotation. A comprehensive quality-assurance program was developed for the authors' stereotactic radiosurgery program that includes medical imaging, linear accelerator mechanical isocentricity, and treatment delivery. For a successful treatment of trigeminal neuralgia with a 4-mm cone, the overall RMS value of equal to or less than 1 mm must be guaranteed.

Sign in / Sign up

Export Citation Format

Share Document