Calculation of the stability, initial post-buckling behavior, and flaw sensitivity of laminated cylingrical shells made of composites

1991 ◽  
Vol 27 (6) ◽  
pp. 594-599
Author(s):  
N. P. Semenyuk
Keyword(s):  
Buckling Behavior ◽  
Post Buckling ◽  
Flaw Sensitivity ◽  
The Stability

Numerical and Experimental Buckling and Post - Buckling Analysis of Composite Cylindrical Panel with Delamination

2013 ◽  
Vol 477-478 ◽  
pp. 39-42
Author(s):  
Marek Barski ◽  
Aleksander Muc ◽  
Przemysław Pastuszak ◽  
Agnieszka Bondyra
Keyword(s):  
Numerical Analysis ◽  
Experimental Verification ◽  
Experimental Analysis ◽  
Cylindrical Panel ◽  
Composite Panel ◽  
Fem Method ◽  
Buckling Behavior ◽  
Post Buckling ◽  
The Stability ◽  
Composite Cylindrical Panel

The present work is devoted to the analysis of a buckling behavior of a cylindrical composite panel. The considered structure is subjected to the uniform axial compression. The wall of the panel consists of the 8 layers. In addition, in the geometrical center of the structure there is a square delamination located between the fourth and the fifth layer. The main goal is to determine the buckling and post - buckling behavior as well as the influence of the delamination on the stability of the structure. The nonlinear numerical analysis is carried out with aid of the FEM method. The experimental verification is also performed. The results obtained from numerical and experimental analysis show very similar behavior of the structure.

Buckling and Post-Buckling Behavior for Roof Strata in Longwall Mining

2012 ◽  
Vol 170-173 ◽  
pp. 751-754
Author(s):  
Qun Song ◽  
Zhi Lin Yang
Keyword(s):  
Longwall Mining ◽  
Main Roof ◽  
Equilibrium Path ◽  
Fracture Characteristics ◽  
Key Stratum ◽  
Buckling Behavior ◽  
Roof Stratum ◽  
Post Buckling ◽  
The Stability ◽  
Roof Strata

In accordance with the occurrence behavior of roof strata and the fracture characteristics of key stratum in shallow seam longwall mining, this paper studied the post-buckling behaviors of key roof stratum in the process of mining by using initial post-buckling theory, which derived a critical load and a breaking span of the main roof during the first weighting, determined the final subsidence for broken key stratum, and presented an application with the example of Daliuta 1203 face. The results indicate that the rock blocks a in are state of non-equilibrium after main roof breaking, the equilibrium path of main roof is unstable from breaking to final subsidence; thick unconsolidated layers above roof have effect on post-buckling behaviors of key stratum; the stability for bifurcation point equilibrium configuration and post-buckling equilibrium path of roof strata could be revealed and an effective method for determining displacement field of imperfection structure could be provided by using initial post -buckling theory.

Buckling Behavior of Tire Breaker Structure

1983 ◽  
Vol 11 (1) ◽  
pp. 3-19
Author(s):  
T. Akasaka ◽  
S. Yamazaki ◽  
K. Asano
Keyword(s):  
Elastic Foundation ◽  
Elastic Moduli ◽  
Wave Length ◽  
Bending Moment ◽  
Experimental Results ◽  
Automobile Tire ◽  
Buckling Behavior ◽  
Post Buckling ◽  
Steel Cord ◽  
Interlaminar Shear

Abstract The buckled wave length and the critical in-plane bending moment of laminated long composite strips of cord-reinforced rubber sheets on an elastic foundation is analyzed by Galerkin's method, with consideration of interlaminar shear deformation. An approximate formula for the wave length is given in terms of cord angle, elastic moduli of the constituent rubber and steel cord, and several structural dimensions. The calculated wave length for a 165SR13 automobile tire with steel breakers (belts) was very close to experimental results. An additional study was then conducted on the post-buckling behavior of a laminated biased composite beam on an elastic foundation. This beam is subjected to axial compression. The calculated relationship between the buckled wave rise and the compressive membrane force also agreed well with experimental results.

Appraisal of Allowable Loads by Simplified Rules

1986 ◽  
Vol 108 (2) ◽  
pp. 131-137
Author(s):  
D. Moulin
Keyword(s):  
Experimental Investigation ◽  
Plastic Region ◽  
Thin Structures ◽  
Geometric Imperfections ◽  
Buckling Behavior ◽  
Simplified Method ◽  
Post Buckling ◽  
Initial Geometric Imperfections ◽  
Fast Breeder Reactors ◽  
Breeder Reactors

This paper presents a simplified method to analyze the buckling of thin structures like those of Liquid Metal Fast Breeder Reactors (LMFBR). The method is very similar to those used for the buckling of beams and columns with initial geometric imperfections, buckling in the plastic region. Special attention is paid to the strain hardening of material involved and to possible unstable post-buckling behavior. The analytical method uses elastic calculations and diagrams that account for various initial geometric defects. An application of the method is given. A comparison is made with an experimental investigation concerning a representative LMFBR component.

A characteristic type of instability in the large deflexions of elastic plates III. Curved rectangular plates in axial compression

1954 ◽  
Vol 222 (1148) ◽  
pp. 44-59 ◽  
Keyword(s):  
Axial Compression ◽  
Rectangular Plates ◽  
Bending Moments ◽  
Elastic Plates ◽  
Characteristic Type ◽  
Circular Tubes ◽  
Axis Parallel ◽  
Post Buckling ◽  
Thin Walled ◽  
The Stability

The analysis of part I is extended to deal with the case of free-edged rectangular plates having an initial curvature about an axis parallel to one pair of opposite edges and loaded by distributed bending moments applied to the straight edges and compressive forces applied to the curved edges. In particular, the stability and post-buckling behaviour of such plates subjected to the compressive forces alone is studied. The axially symmetrical buckling of thin-walled circular tubes in axial compression is also considered. Experimental plates are found to buckle at loads rather lower than those predicted.

Geometrical Stiffness of Thin-Walled I-Beam Element Based on Rigid-Beam Assemblage Concept

2012 ◽  
Vol 28 (1) ◽  
pp. 97-106 ◽  
Author(s):  
J. D. Yau ◽  
S.-R. Kuo
Keyword(s):  
Stiffness Matrix ◽  
Virtual Work ◽  
Bending Moment ◽  
Beam Element ◽  
Narrow Beam ◽  
Cross Sectional ◽  
Geometric Stiffness ◽  
Buckling Behavior ◽  
Post Buckling ◽  
Thin Walled

ABSTRACTUsing conventional virtual work method to derive geometric stiffness of a thin-walled beam element, researchers usually have to deal with nonlinear strains with high order terms and the induced moments caused by cross sectional stress results under rotations. To simplify the laborious procedure, this study decomposes an I-beam element into three narrow beam components in conjunction with geometrical hypothesis of rigid cross section. Then let us adopt Yanget al.'s simplified geometric stiffness matrix [kg]12×12of a rigid beam element as the basis of geometric stiffness of a narrow beam element. Finally, we can use rigid beam assemblage and stiffness transformation procedure to derivate the geometric stiffness matrix [kg]14×14of an I-beam element, in which two nodal warping deformations are included. From the derived [kg]14×14matrix, it can take into account the nature of various rotational moments, such as semi-tangential (ST) property for St. Venant torque and quasi-tangential (QT) property for both bending moment and warping torque. The applicability of the proposed [kg]14×14matrix to buckling problem and geometric nonlinear analysis of loaded I-shaped beam structures will be verified and compared with the results presented in existing literatures. Moreover, the post-buckling behavior of a centrally-load web-tapered I-beam with warping restraints will be investigated as well.

scholarly journals The post buckling behavior of a clamped circular plate

1955 ◽  
Vol 12 (4) ◽  
pp. 397-401 ◽  
Author(s):  
Sol R. Bodner
Keyword(s):  
Circular Plate ◽  
Buckling Behavior ◽  
Post Buckling
Sign in / Sign up

Export Citation Format

Share Document