Effect of Microstructure and Segregation of Elements on the Impact Toughness of High-Strength Low-Carbon Bainitic Steel

2016 ◽  
Vol 58 (3-4) ◽  
pp. 138-141
Author(s):  
Du Minxian ◽  
Peng Huaxia ◽  
Tian Hongbin ◽  
Sun Li ◽  
Ou Ling
Keyword(s):  
Impact Toughness ◽  
High Strength ◽  
Bainitic Steel ◽  
Low Carbon ◽  
The Impact ◽  
Effect Of Microstructure

Effect of Rolling Process on Impact Toughness in High Strength Low Carbon Bainitic Steel

2015 ◽  
Vol 816 ◽  
pp. 743-749 ◽  
Author(s):  
Xiao Long Yang ◽  
Xiao Dong Tan ◽  
Yun Bo Xu ◽  
Zhi Ping Hu ◽  
Yong Mei Yu ◽  
...  
Keyword(s):  
Impact Toughness ◽  
Ductile Fracture ◽  
Cleavage Fracture ◽  
Charpy Impact ◽  
High Strength ◽  
Rolling Process ◽  
Bainitic Steel ◽  
Low Carbon ◽  
Austenite Recrystallization ◽  
The Impact

Based on TMCP and UFC technology, the microstructures and impact toughness of low carbon bainitic steel were studied in this paper. The bainite morphology and fracture surfaces of Charpy impact specimens were observed by SEM, and mechanical properties of bainitic steel were measured by tensile and impact test. The results showed that the yield and tensile strengths of steel were 804MPa and 1015MPa, and elongation was 15.7% when the rolling was finished in the austenite recrystallization region. The steel rolled below Tnr temperature obtained tht yield strength of 930 MPa, tensile strength of 1090 MPa and elongation of 16.2%. However, the impact toughness was deteriorated in the steel rolled above Tnr temperature while the excellent impact toughness existed in the steel rolled below Tnr temperature. The impact toughness of steel rolled below Tnr temperature was 140J at-60°C, while the impact toughness of 15J at the same temperature was obtained for the steel rolled above Tnr temperature. The large cleavage fracture region on the fracture surface occured with the decrease of tested temperature in the steel rolled above Tnr temperature and inevitably reduced the impact toughness, while the main ductile fracture existed in the steel rolled below Tnr temperature at the same temperature. The rolling process of steel can strongly affect impact toughness of low carbon bainitic steel. Hence, the different rolling processes can adjust the occurrence of cleavage fracture and ductile fracture in order to improve the impact toughness.

Impact of Reversed Austenite on the Impact Toughness of the High-Strength Steel of Low Carbon Medium Manganese

JOM ◽  
2018 ◽  
Vol 70 (5) ◽  
pp. 672-679 ◽  
Author(s):  
Guanqiao Su ◽  
Xiuhua Gao ◽  
Dazheng Zhang ◽  
Linxiu Du ◽  
Jun Hu ◽  
...  
Keyword(s):  
Impact Toughness ◽  
High Strength Steel ◽  
High Strength ◽  
Low Carbon ◽  
Reversed Austenite ◽  
The Impact

scholarly journals Tempforming as an Advanced Processing Method for Carbon Steels

Metals ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1566
Author(s):  
Anastasiya Dolzhenko ◽  
Rustam Kaibyshev ◽  
Andrey Belyakov
Keyword(s):  
Impact Toughness ◽  
Crack Propagation ◽  
Large Strain ◽  
High Strength ◽  
Close Relation ◽  
Carbon Steels ◽  
Processing Method ◽  
Propagation Mode ◽  
Displacement Curve ◽  
The Impact

The microstructural mechanisms providing delamination toughness in high-strength low-alloyed steels are briefly reviewed. Thermo-mechanical processing methods improving both the strength and impact toughness are described, with a close relation to the microstructures and textures developed. The effect of processing conditions on the microstructure evolution in steels with different carbon content is discussed. Particular attention is paid to tempforming treatment, which has been recently introduced as a promising processing method for high-strength low-alloyed steel semi-products with beneficial combination of strength and impact toughness. Tempforming consists of large strain warm rolling following tempering. In contrast to ausforming, the steels subjected to tempforming may exhibit an unusual increase in the impact toughness with a decrease in test temperature below room temperature. This phenomenon is attributed to the notch blunting owing to easy splitting (delamination) crosswise to the principle crack propagation. The relationships between the crack propagation mode, the delamination fracture, and the load-displacement curve are presented and discussed. Further perspectives of tempforming applications and promising research directions are outlined.

Physical Simulation of Weldability of Weldox 1300 Steel

2013 ◽  
Vol 762 ◽  
pp. 551-555 ◽  
Author(s):  
Marek Stanislaw Węglowski ◽  
Marian Zeman ◽  
Miroslaw Lomozik
Keyword(s):  
Mechanical Properties ◽  
Impact Toughness ◽  
Physical Simulation ◽  
High Strength ◽  
Parent Material ◽  
Cooling Time ◽  
Electron Microscopies ◽  
Transmission Electron ◽  
Transformation Diagrams ◽  
The Impact

In the present study, the investigation of weldability of new ultra-high strength - Weldox 1300 steel has been presented. The thermal simulated samples were used to investigate the effect of welding cooling time t8/5 on the microstructure and mechanical properties of the heat affected zone (HAZ). In the frame of these investigation the microstructure was studied by the light (LM) and transmission electron microscopies (TEM). It has been shown that the microstructure of the Weldox 1300 steel is composed of tempered martensite, and inside the laths the minor precipitations mainly V(CN) and molybdenum carbide Mo2C were observed. Mechanical properties of parent material were analysed by the tensile, impact and hardness tests. In details the influence of cooling time in the range of 2,5 - 300 s. on hardness, impact toughness and microstructure of simulated HAZ was studied by using welding thermal simulation test. The results show that the impact toughness and hardness decrease with the increase of t8/5 under the condition of a single thermal cycle in simulated HAZ. The continuous cooling transformation diagrams (CCT-W for welding conditions) of Weldox 1300 steel for welding purposes was also elaborated. The steel Weldox 1300 for cooling time in the range of 2,5 - 4 s showed martensite microstructure, for time from 4 s to 60 s mixture of martensite and bainite, and for longer cooling time mixture of ferrite, bainite and martensite. The results indicated that the weldability of Weldox 1300 steel is limited and to avoid the cold cracking the preheating procedure or medium net linear heat input should be used.

Effect of Welding Processes with High Heat Input on the Microstructure and Toughness of Coarse-Grained Heat-Affected Zone of a High-Strength High-Toughness Steel

2018 ◽  
Vol 937 ◽  
pp. 61-67
Author(s):  
Yu Jie Li ◽  
Jin Wei Lei ◽  
Xuan Wei Lei ◽  
Oleksandr Hress ◽  
Kai Ming Wu
Keyword(s):  
Low Temperature ◽  
Impact Toughness ◽  
Heat Affected Zone ◽  
Heat Input ◽  
High Strength ◽  
High Heat ◽  
Coarse Grained ◽  
Low Temperature Impact Toughness ◽  
The Impact ◽  
Welding Processes

Utilizing submerged arc welding under heat input 50 kJ/cm on 60 mm thick marine engineering structure plate F550, the effect of preheating and post welding heat treatment on the microstructure and impact toughness of coarse-grained heat-affected zone (CGHAZ) has been investigated. The original microstructure of the steel plate is tempered martensite. The yield and tensile strength is 610 and 660 MPa, respectively. The impact absorbed energy at low temperature (-60 °C) at transverse direction reaches about 230~270 J. Welding results show that the preheating at 100 °C did not have obvious influence on the microstructure and toughness; whereas the tempering at 600 °C for 2.5 h after welding could significantly reduce the amount of M-A components in the coarse-grained heat-affected zone and thus improved the low temperature impact toughness.

scholarly journals Evaluation of Microstructure and Impact Toughness of Shielded Metal Arc Dissimilar Weldments of High Strength Low Alloy Steel and Austenitic Stainless Steel

2020 ◽  
Vol 5 (2) ◽  
Author(s):  
Misbahu A Hayatu ◽  
Emmanuel T Dauda ◽  
Ola Aponbiede ◽  
Kamilu A Bello ◽  
Umma Abdullahi
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Impact Toughness ◽  
Impact Energy ◽  
High Strength ◽  
Impact Testing ◽  
Welding Parameters ◽  
Dissimilar Weld ◽  
Weld Joints ◽  
The Impact

There is a growing interest for novel materials of dissimilar metals due to higher requirements needed for some critical engineering applications. In this research, different dissimilar weld joints of high strength low alloy (HSLA) and 316 austenitic stainless steel grades were successfully produced using shielded metal arc welding (SMAW) process with 316L-16 and E7018 electrodes. Five variations of welding currents were employed within the specified range of each electrode. Other welding parameters such as heat inputs, welding speeds, weld sizes, arc voltages and time of welding were also varied. Specimens for different weld joint samples were subjected to microstructural studies using optical and scanning electron microscopes. The impact toughness test was also conducted on the samples using Izod impact testing machine. The analysis of the weld microstructures indicated the presence of type A and AF solidification patterns of austenitic stainless steels. The results further showed that the weld joints consolidated with E7018 electrode presented comparatively superior impact energy to the weldments fabricated by 316L-16 electrode. The optimum impact energy of E7018-weld joints (51J) was attained at higher welding heat inputs while that of 316L-16-weld joints (35J) was achieved at lower welding heat inputs, which are necessary requirements for the two electrodes used in the experiment. Hence, the dissimilar weld joints investigated could meet requirement for engineering application in offshore and other critical environments.Keywords—Dissimilar metal weld, heat input, impact toughness, microstructures

Effects of Al, Si and N Content on the Formation of M-A Constituent and HAZ Toughness of Ti-Containing Low-Carbon Steel

2021 ◽  
Vol 1016 ◽  
pp. 42-49
Author(s):  
Kook Soo Bang ◽  
Joo Hyeon Cha ◽  
Kyu Tae Han ◽  
Hong Chul Jeong
Keyword(s):  
Carbon Steel ◽  
Impact Toughness ◽  
Low Carbon Steel ◽  
Charpy Impact ◽  
Coarse Grained ◽  
Low Carbon ◽  
N Content ◽  
Si Content ◽  
The Impact ◽  
Haz Toughness

The present work investigated the effects of Al, Si, and N content on the impact toughness of the coarse-grained heat-affected zone (CGHAZ) of Ti-containing low-carbon steel. Simulated CGHAZ of differing Al, Si, and N contents were prepared, and Charpy impact toughness was determined. The results were interpreted in terms of microstructure, especially martensite-austenite (M-A) constituent. All elements accelerated ferrite transformation in CGHAZ but at the same time increased the amount of M-A constituent, thereby deteriorating CGHAZ toughness. It is believed that Al, Si, and free N that is uncombined with Ti retard the decomposition of austenite into pearlite and increase the carbon content in the last transforming austenite, thus increasing the amount of M-A constituent. Regardless of the amount of ferrite in CGHAZ, its toughness decreased linearly with an increase of M-A constituent in this experiment, indicating that HAZ toughness is predominantly affected by the presence of M-A constituent. When a comparison of the effectiveness is made between Al and Si, it showed that a decrease in Si content is more effective in reducing M-A constituents.

Sign in / Sign up

Export Citation Format

Share Document