Effect of cooling rate on crystallization behavior of milk fat fraction/sunflower oil blends

2002 ◽  
Vol 79 (11) ◽  
pp. 1055-1062 ◽  
Author(s):  
S. Martini ◽  
M. L. Herrera ◽  
R. W. Hartel
2001 ◽  
Vol 49 (7) ◽  
pp. 3223-3229 ◽  
Author(s):  
S. Martini ◽  
M. L. Herrera ◽  
R. W. Hartel

2003 ◽  
Vol 51 (22) ◽  
pp. 6550-6557 ◽  
Author(s):  
Marina Cerdeira ◽  
Silvana Martini ◽  
Richard W. Hartel ◽  
Maria Lidia Herrera

2011 ◽  
Vol 59 (6) ◽  
pp. 2689-2695 ◽  
Author(s):  
Rebekah M. Kerr ◽  
Xenia Tombokan ◽  
Supriyo Ghosh ◽  
Silvana Martini

1992 ◽  
Vol 67 (03) ◽  
pp. 352-356 ◽  
Author(s):  
Marja Mutanen ◽  
Riitta Freese ◽  
Liisa M Valsta ◽  
Irma Ahola ◽  
Antti Ahlström

SummaryIn this highly controlled trial, 26 normolipidemic men (average age 28 years, range 18 to 60) were fed a baseline diet high in milk fat (MF) (fat 36% of energy, saturates 19%, monounsaturates 11%, polyunsaturates 4%), followed by a diet high in sunflower oil (SO) (fat 38% of energy, saturates 13%, monounsaturates 10%, polyunsaturates 13%) and another diet high in low erucic-acid rapeseed oil (RO) (fat 38% of energy, saturates 12%, monounsaturates 16%, polyunsaturates 8%). All diets were mixed natural diets with the same cholesterol contents. The baseline milk fat diet was given for 14 days and the oil diets for 24 days in a blind cross-over design. The platelet in vitro aggregation (slope %/min) induced by 1, 2 and 3 pM ADP and collagen (25 pg/ml PRP) was highly significantly (p <0.001) increased after both oil diets when compared with the results from the milk fat diet. The aggregation pattern determined by threshold collagen concentration confirmed increased collagen sensitivity of the platelets after the rapeseed oil diet (p <0.001). The enhancement of platelet aggregation was associated with increased in vitro platelet thromboxane production after the oil diets vs. the milk fat diet (p <0.05 after the sunflower oil diet and p <0.001 after the rapeseed oil diet).


2018 ◽  
Vol 116 (1) ◽  
pp. 110
Author(s):  
Lixiong Shao ◽  
Jiang Diao ◽  
Wang Zhou ◽  
Tao Zhang ◽  
Bing Xie

The growth behaviour of spinel crystals in vanadium slag with high Cr2O3 content was investigated and clarified by statistical analyses based on the Crystal Size Distribution (CSD) theory. The results indicate that low cooling rate and Cr2O3 content benefit the growth of spinel crystals. The chromium spinel crystals firstly precipitated and then acted as the heterogeneous nuclei of vanadium and titanium spinel crystals. The growth mechanisms of the spinel crystals at the cooling rate of 5 K/min consist two regimes: firstly, nucleation control in the temperature range of 1873 to 1773 K, in which the shapes of CSD curves are asymptotic; secondly, surface and supply control within the temperature range of 1773 to 1473 K, in which the shapes of CSD curves are lognormal. The mean diameter of spinel crystals increases from 3.97 to 52.21 µm with the decrease of temperature from 1873 to 1473 K.


2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Guangming Dai ◽  
Lihua Zhan ◽  
Chenglong Guan ◽  
Minghui Huang

Abstract In this study, the differential scanning calorimetry (DSC) tests were performed to measure the nonisothermal crystallization behavior of carbon fiber reinforced polyether ether ketone (CF/PEEK) composites under different cooling rates. The characteristic parameters of crystallization were obtained, and the nonisothermal crystallization model was established. The crystallization temperature range of the material at different cooling rates was predicted by the model. The unidirectional laminates were fabricated at different cooling rates in the crystallization temperature range. The results showed that the crystallization temperature range shifted to a lower temperature with the increase of cooling rate, the established nonisothermal crystallization model was consistent with the DSC test results. It is feasible to shorten the cooling control range from the whole process to the crystallization range. The crystallinity and transverse tensile strength declined significantly with the increase of the cooling rate in the crystallization temperature range. The research results provided theoretical support for the selection of cooling conditions and temperature control range, which could be applied to the thermoforming process of semi-crystalline polymer matrixed composites to improve the manufacturing efficiency.


Sign in / Sign up

Export Citation Format

Share Document