Re-refining of used lubricant oil by solvent extraction using central composite design method

2017 ◽  
Vol 34 (9) ◽  
pp. 2435-2444 ◽  
Author(s):  
Ghassan Rokan Daham ◽  
Adnan AbdulJabbar AbdulRazak ◽  
Adel Sharif Hamadi ◽  
Ayad Ahmed Mohammed
Keyword(s):  
Solvent Extraction ◽  
Central Composite Design ◽  
Design Method ◽  
Lubricant Oil ◽  
Central Composite ◽  
Used Lubricant Oil

scholarly journals Leaching and solvent extraction purification of zinc from Mehdiabad complex oxide ore

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Faraz Soltani ◽  
Hossna Darabi ◽  
Reza Aram ◽  
Mahdi Ghadiri
Keyword(s):  
Solvent Extraction ◽  
Environmental Pollution ◽  
Central Composite Design ◽  
Complex Oxide ◽  
Hydrometallurgical Process ◽  
Purification Process ◽  
Optimum Conditions ◽  
Leaching Experiments ◽  
Central Composite ◽  
Sulphuric Acid Concentration

AbstractAn integrated hydrometallurgical process was used for the zinc leaching and purification from a zinc ore containing 9.75 wt% zinc. The zinc minerals in the ore were hemimorphite, willemite, and calcophanite. Main gangue minerals were quartz, goethite, hematite, and calcite. Central composite design (CCD) method was used to design leaching experiments and the optimum conditions were found as follows: 30% of solid fraction, 22.05% sulphuric acid concentration, and the leaching temperature of 45 °C. The PLS containing 35.07 g/L zinc, 3.16 g/L iron, and 4.58 g/L manganese impurities was produced. A special purification process including Fe precipitation and Zn solvent extraction was implemented. The results showed that after precipitation of iron, Zn extraction of 88.5% was obtained with the 2 stages extraction system composed of 30 vol% D2EHPA as extractant. The overall Zn recovery from the ore was 71.44%. Therefore, an appropriate solution containing 16.6 g/L Zn, 0.05 g/L Fe, and 0.11 g/L Mn was prepared for the electro-winning unit without using the roasting and calcination steps (conventional method), which result in environmental pollution.

scholarly journals Optimization of Eugenol Extraction from Clove Oil using Response Surface Methodology

2015 ◽  
Vol 9 (11) ◽  
pp. 68
Author(s):  
Widayat Widayat ◽  
Hadiyanto Hadiyanto ◽  
Bambang Cahyono ◽  
Ngadiwiyana Ngadiwiyana
Keyword(s):  
Response Surface Methodology ◽  
Optimum Condition ◽  
Central Composite Design ◽  
Response Surface ◽  
Design Method ◽  
Main Process ◽  
Clove Oil ◽  
Design Variables ◽  
Central Composite

The objective of this research was to obtain optimum condition of eugenol production from clove oil using a central composite design method. The main process occured in the eugenol production was saphonification and neutralization processes. In order to optimize these processes, the ratio of NaOH/clove oil and temperature were studied as design variables i.e. ratio of NaOH/clove oil=1:2.5-1:3.5 while temperature was varied between 40 and 60oC. The yield of eugenol was considered as the main response in of this experiment. The result showed that the optimum condition was achieved when the temperature and the ratio of NaOH/clove oil were 50oC and 2.75:1, respectively and the yield was 39.17%.<br />

Extraction of carotenoids from Lycium ferocissimum fruits for cotton dyeing: Optimization survey based on a central composite design method

2016 ◽  
Vol 17 (1) ◽  
pp. 36-43 ◽  
Author(s):  
Khaled Faidi ◽  
Noureddine Baaka ◽  
Saoussen Hammami ◽  
Ridha El Mokni ◽  
Zine Mighri ◽  
...  
Keyword(s):  
Central Composite Design ◽  
Design Method ◽  
Central Composite ◽  
Cotton Dyeing
Sign in / Sign up

Export Citation Format

Share Document