Injection production ratio optimization calculation model based on new water--drive type curve

2021 ◽  
Vol 14 (18) ◽  
Author(s):  
Feng Liu ◽  
Xianlin Ma ◽  
Junbin Chen ◽  
Yancheng Liu ◽  
Fei Yang
2020 ◽  
Vol 2020 ◽  
pp. 1-17
Author(s):  
Hai Yang ◽  
Yue Rao ◽  
Li Li ◽  
Haibo Liang ◽  
Tao Luo ◽  
...  

At present, real-time online measurement of fluid density is of great significance to improve the automation level of petrochemical and food industries. The tuning fork density sensor is widely used because of its characteristics of real-time online measurement, high measurement accuracy, simple structure, and convenient use. The traditional tuning fork density sensor in the market has the disadvantage of low resolution and being susceptible to liquid viscosity, which makes the sensor’s measurement accuracy low and not suitable for the measurement of high-viscosity liquid density. The measurement resolution and antiviscosity interference capability of the tuning fork density sensor are two major indexes to measure the measurement performance of the sensor, among the antiviscosity interference capability refers to the degree to which the measurement results of the sensor are affected by viscosity properties. However, the structural design of the tuning fork density sensor results in the conflict between the measurement resolution and the antiviscosity interference capability of the sensor, and the improvement of one performance is bound to affect the performance of the other. Aiming at the problem of how to balance the measuring performance of the tuning fork sensor, a density calculation model based on viscosity compensation is proposed in this paper. By studying the working principle and structure design of the tuning fork, the vibration characteristics of tuning fork in liquid with different viscosities and densities are modelled and simulated. From the results of simulation analysis, the better set of dimensions with balanced measuring performance is selected. Not only does the structure of the tuning fork have the characteristics of high resonance frequency, but also the measured results are less affected by the viscosity of the liquid. To solve the problem that density measurement is still affected by high-viscosity liquid after tuning fork dimension optimization, in this paper, the partial least square model is used to fit the experimental data of the frequency-density characteristics; then, the density calculation model based on the viscosity compensation is obtained by combining the frequency-viscosity characteristic experiment. Finally, through the performance test experiment comparing with the traditional tuning fork density sensor, the measurement resolution of the improved tuning fork density sensor is as high as 0.0001 g/cm3; within the viscosity range of 180 MPa·s, the accuracy reached ±0.001 g/cm3, and within 480 MPa·s, the measurement accuracy reached ±0.002 g/cm3. When the liquid viscosity reaches more than 10 MPa·s, the improved tuning fork density sensor has better overall measurement performance than the traditional tuning fork density sensor, and both of its measurement resolution and antiviscosity interference capability have been greatly improved.


2013 ◽  
Vol 353-356 ◽  
pp. 2645-2651
Author(s):  
Yi Zhi Yan ◽  
Chang Xin Xiong ◽  
Zhi Min Su

Studying the important effects of sediments on the seismic response of dams ,This paper established the calculation model based on regarding the water reservoir as compressible fluid ,the dam and the foundation as an elastic solid, the sediment as Liquid-Solid two-phase porous medium. The results showed that the sediment thickness and properties have important effects on the dam seismic. Increasing the thickness of sediment ,the seismic response of acceleration significantly decreased, the hydrodynamic pressure significantly reduced , which is benefited to the safety of the dam.


2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Guanghui Li ◽  
Fengyu Ren ◽  
Hangxing Ding ◽  
Huan Liu ◽  
Mingzhi Sun ◽  
...  

In this paper, stope structure optimization during sublevel caving mining is considered under the condition that the isolated draw zones (IDZs) are nonstandard ellipsoid, which is realized by dynamically adjusting the arrangement of IDZs and quantifying the degree of intersection of IDZs according to an ore profit and loss calculation model. A dynamic intersecting arrangement model based on IDZs was proposed, which can dynamically adjust the sublevel height and drift spacing according to the ore-rock bulk flow parameters, economic indicators, occurrence condition of the ore body, drilling machine, and so forth. Based on the model, the range of drift spacing, the lower volume of crestal residual ore, and the higher volume of mixing waste rock are calculated. By deducing the function of ore profit and loss, a calculation model for ore profit and loss is established to quantify the degree of intersection of IDZs and determine the best stope structure. Using the constructed dynamic intersecting arrangement model, a stope structure of −213 m to −303 m in the Yanqianshan Iron Mine was designed, with a sublevel height of 22.5 m and a drift spacing of 20.5 m. A physical drawing model was designed, and three physical simulation experiment schemes were conducted to compare and analyse the ore loss and dilution of the intersecting arrangement model and the traditional tangent arrangement model. The results showed that the loss rate decreased by 3.66% and the dilution rate increased by only 0.22%, thus verifying the effectiveness and applicability of the model to optimize the stope structure.


Sign in / Sign up

Export Citation Format

Share Document