Tool life modeling for evaluating the effects of cutting speed and reinforcements on the machining of particle reinforced metal matrix composites

2010 ◽  
Vol 17 (3) ◽  
pp. 353-362 ◽  
Author(s):  
Metin Kök
Keyword(s):  
Metal Matrix Composites ◽  
Tool Life ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Matrix Composites

scholarly journals Machining of Titanium Metal Matrix Composites: Progress Overview

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 5011
Author(s):  
Cécile Escaich ◽  
Zhongde Shi ◽  
Luc Baron ◽  
Marek Balazinski
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Wear Mechanisms ◽  
Metal Matrix ◽  
Dust Emission ◽  
Cutting Speed ◽  
Matrix Composites ◽  
Titanium Metal ◽  
Machining Processes ◽  
Tool Wear Mechanisms

The TiC particles in titanium metal matrix composites (TiMMCs) make them difficult to machine. As a specific MMC, it is legitimate to wonder if the cutting mechanisms of TiMMCs are the same as or similar to those of MMCs. For this purpose, the tool wear mechanisms for turning, milling, and grinding are reviewed in this paper and compared with those for other MMCs. In addition, the chip formation and morphology, the material removal mechanism and surface quality are discussed for the different machining processes and examined thoroughly. Comparisons of the machining mechanisms between the TiMMCs and MMCs indicate that the findings for other MMCs should not be taken for granted for TiMMCs for the machining processes reviewed. The increase in cutting speed leads to a decrease in roughness value during grinding and an increase of the tool life during turning. Unconventional machining such as laser-assisted turning is effective to increase tool life. Under certain conditions, a “wear shield” was observed during the early stages of tool wear during turning, thereby increasing tool life considerably. The studies carried out on milling showed that the cutting parameters affecting surface roughness and tool wear are dependent on the tool material. The high temperatures and high shears that occur during machining lead to microstructural changes in the workpiece during grinding, and in the chips during turning. The adiabatic shear band (ASB) of the chips is the seat of the sub-grains’ formation. Finally, the cutting speed and lubrication influenced dust emission during turning but more studies are needed to validate this finding. For the milling or grinding, there are major areas to be considered for thoroughly understanding the machining behavior of TiMMCs (tool wear mechanisms, chip formation, dust emission, etc.).

Comparison of machining characteristics of metal matrix composites using CO2 laser curve cutting process

2017 ◽  
Vol 232 (3) ◽  
pp. 349-368 ◽  
Author(s):  
Vikas Sharma ◽  
Vinod Kumar
Keyword(s):  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Morphological Changes ◽  
Cutting Speed ◽  
Matrix Composites ◽  
Composites Materials ◽  
Input Variables ◽  
Output Characteristics ◽  
Metal Matrix Composite Material ◽  
Machining Characteristics

In the present work, the effects of input variables of laser beam machining on the machining characteristics of the metal matrix composites reinforced with SiC, Al2O3, and ZrO2 particles were investigated. The comparison of the machining characteristics has been done to analyze the behavior of various reinforced particles with the variation of laser machining variables. Various output characteristics such as dross height, kerf deviation, and striations angle have been investigated and compared with each metal matrix composite material. Parameters such as cutting speed, reinforced particles, and cut profile were found to be the most significant factors influencing the various output characteristics. The morphological changes in the structure have been examined using scanning electron microscopy and X-ray diffraction technique for the agglomeration of the reinforced particles. The crack and recast layer formation has been examined in the specimens of higher quantity of the reinforced particles. It was analyzed that the metal matrix composites material reinforced with SiC particles has shown different behaviors as compared to other metal matrix composites materials.

On the Optimisation Into Wire Electro-Discharge Machining of Al/Al2O3P Composites

2007 ◽  
Author(s):  
N. G. Patil ◽  
P. K. Brahmankar ◽  
L. G. Navale
Keyword(s):  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Kerf Width ◽  
Feed Speed ◽  
Machining Parameters ◽  
Matrix Composites ◽  
Electro Discharge Machining ◽  
Pulse On Time ◽  
Machining Parameter

Non-traditional process like wire electro-discharge machining (WEDM) is found to show a promise for machining metal matrix composites (MMCs). However, the machining information for the difficult-to-machine particle-reinforced material is inadequate. This paper is focused on experimental investigation to examine the effect of electrical as well as nonelectrical machining parameters on performance in wire electro-discharge machining of metal matrix composites (Al/Al2O3p). Taguchi orthogonal array was used to study the effect of combination of reinforcement, current, pulse on-time, off-time, servo reference voltage, maximum feed speed, wire speed, flushing pressure and wire tension on kerf width and cutting speed. Reinforcement percentage, current, on-time was found to have significant effect on cutting rate and kerf width. The optimum machining parameter combinations were obtained for cutting speed and kerf width separately.

scholarly journals Tool wear and surface quality of metal matrix composites due to machining: A review

2016 ◽  
Vol 231 (5) ◽  
pp. 739-752 ◽  
Author(s):  
Ferial Hakami ◽  
Alokesh Pramanik ◽  
Animesh K Basak
Keyword(s):  
Tool Wear ◽  
Metal Matrix Composite ◽  
Metal Matrix Composites ◽  
Surface Quality ◽  
Tool Life ◽  
Metal Matrix ◽  
Cutting Tool ◽  
Matrix Composites ◽  
Machined Surface

Higher tool wear and inferior surface quality of the specimens during machining restrict metal matrix composites’ application in many areas in spite of their excellent properties. The researches in this field are not well organized, and knowledge is not properly linked to give a complete overview. Thus, it is hard to implement it in practical fields. To address this issue, this article reviews tool wear and surface generation and latest developments in machining of metal matrix composites. This will provide an insight and scientific overview in this field which will facilitate the implementation of the obtained knowledge in the practical fields. It was noted that the hard reinforcements initially start abrasive wear on the cutting tool. The abrasion exposes new cutting tool surface, which initiates adhesion of matrix material to the cutting tool and thus causes adhesion wear. Built-up edges also generate at lower cutting speeds. Although different types of coating improve tool life, only diamond cutting tools show considerably longer tool life. The application of the coolants improves tool life reasonably at higher cutting speed. Pits, voids, microcracks and fractured reinforcements are common in the machined metal matrix composite surface. These are due to ploughing, indentation and dislodgement of particles from the matrix due to tool–particle interactions. Furthermore, compressive residual stress is caused by the particles’ indentation in the machined surface. At high feeds, the feed rate controls the surface roughness of the metal matrix composite; although at low feeds, it was controlled by the particle fracture or pull out. The coarser reinforced particles and lower volume fraction enhance microhardness variations beneath the machined surface.

Surface integrity in machining of AZ91/SiC composites

2021 ◽  
pp. 095440622110179
Author(s):  
A Asgari ◽  
M Sedighi
Keyword(s):  
Metal Matrix Composites ◽  
Surface Integrity ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Weight Ratio ◽  
Depth Of Cut ◽  
Matrix Composites ◽  
Machined Surface ◽  
Sic Particles ◽  
Finished Surface

Use of metal matrix composites (MMC) is growing due to their high strength-to-weight ratio, resistance to wear, creep, etc. Machining of metal-matrix composites (MMC) faces many challenges, especially with regard to obtaining a finished surface with high quality. In this research, AZ91/SiC samples with different volume fractions are machined at different cutting conditions with respect to feed rate, cutting speed, and depth of cut. Surface integrity of the machined samples is analyzed by different methods such as tactile profilometer and 3D surface topography to investigate the SiC effects on the finished surface. Additionally, sample surfaces are evaluated by scanning electron microscope (SEM) and with energy-dispersive X-ray (EDS) to assess the surface defects formed around reinforcement materials. Results indicate SiC particles decline the surface quality and uniformity due to the formation of some defects such as micro cracks, holes, and undesired deformations when the cutting process. Also, subsurface SiC particles close to the machined surface are cracked after machining.

Effect of SiCp Reinforcement on Machinability of A356 Alloy Metal Matrix Composites

2016 ◽  
Vol 852 ◽  
pp. 142-148
Author(s):  
K. Jayakumar
Keyword(s):  
Surface Roughness ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
End Milling ◽  
Cutting Speed ◽  
A356 Alloy ◽  
Experimental Result ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Matrix Composites

Machining of Aluminum Metal Matrix Composites (AMMCs) is a challenge for manufacturing industries due to their heterogeneous constituents which vary from soft matrix to hard reinforcements and their interfaces. To overcome the difficulties in machining of MMCs, researchers are continuously working to find the optimum process or machining parameters. In this work, End milling studies were carried out in A356 alloy powder-SiC particles (1 μm) in 0, 5, 10, 15 volume % reinforced AMMCs synthesised by vacuum hot pressing (VHP) route.The influence of machining parameters such as cutting speed, feed and depth of cut on the prepared composites in terms of surface roughness (Ra) and material removal rate (MRR) are measured from experimental study. Experiments were conducted as per Taguchi L16 orthogonal array with 4 factors and 4 levels.From the experimental result, it was identified that surface roughness varied from 0.214 μm to 4.115 μm and MRR varied from minimum of 1.11 cm3/min to maximum of 9.65 cm3/min. It is also observed that, MRR increased with increase in machining parameters and reinforcement quantity. Similarly, surface roughness decreased for increase of cutting speed, SiC particle (SiCp) reinforcement and increased for increase in feed and depth of cut. The optimum condition were observed in higher speed, lower feed and higher depth of cut on MMC with higher SiC content (15%) for getting higher machinability.

scholarly journals Influence of Machining Parameter on Tool Life While Machining Hybrid Metal Matrix Composites

2020 ◽  
Vol 08 (06) ◽  
pp. 440-458
Author(s):  
C. R. Prakash Rao ◽  
V. Ravi Kumar ◽  
D. V. Ravi Kumar ◽  
Poorna Chandra ◽  
M. Vedavyasa ◽  
...  
Keyword(s):  
Metal Matrix Composites ◽  
Tool Life ◽  
Metal Matrix ◽  
Matrix Composites ◽  
Hybrid Metal Matrix Composites ◽  
Machining Parameter

Some Investigations Into Multi-Objective Optimization of Wire Electro-Discharge Machining of Al/SiCp Composites

2007 ◽  
Author(s):  
N. G. Patil ◽  
P. K. Brahmankar ◽  
L. G. Navale
Keyword(s):  
Metal Matrix Composites ◽  
Grey Relational Analysis ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Kerf Width ◽  
Matrix Composites ◽  
Multi Objective Optimization ◽  
Relational Analysis ◽  
Electro Discharge Machining ◽  
Grey Relational

Non-traditional process like wire electro-discharge machining (WEDM) is found to show a promise for machining metal matrix composites (MMCs). However, the machining information for the difficult-to-machine particle-reinforced material is inadequate. This paper is focused on experimental investigation to examine the effect of electrical as well as non-electrical machining parameters on performance in wire electro-discharge machining of metal matrix composites (Al/SiCp). Taguchi orthogonal arrays were employed to study the effects of combinations of voltage, current, pulse on-time, off-time, and wire speed and wire tension on kerf width and cutting speed. Voltage, current, and on-time were found to have significant effect on cutting speed and kerf width. The optimum machining parameter combinations were obtained for cutting speed and kerf width separately. Further, multi-objective optimization was done using Taguchi-Grey relational analysis. The process has been improved with the aid of Grey relational analysis and Taguchi orthogonal array. The results have been verified with confirmation experiments.

Sign in / Sign up

Export Citation Format

Share Document