scholarly journals Influence of arc energy and filler metal composition on the microstructure in wire arc additive manufacturing of duplex stainless steels

2020 ◽  
Vol 65 (1) ◽  
pp. 47-56
Author(s):  
Benjamin Wittig ◽  
Manuela Zinke ◽  
Sven Jüttner
Keyword(s):  
Stainless Steels ◽  
Filler Metal ◽  
Welding Process ◽  
Optical Emission ◽  
Duplex Stainless Steels ◽  
Cold Metal Transfer ◽  
Thin Walled Structures ◽  
Metal Composition ◽  
Cold Metal ◽  
Wire Arc Additive Manufacturing

AbstractThe influence of arc energy and filler metal composition on the microstructure of additively welded thin-walled structures of duplex stainless steels was investigated using different commercially available standard and superduplex solid wire electrodes commonly used today. As welding process, the cold metal transfer (CMT) process was used. The arc energy and cooling rate were varied by adjusting the wire feed and welding speed. Optical emission spectroscopy (OES) and carrier gas melt extraction (CGME) were used to determine the chemical composition of the specimens. The ferrite content was determined both by magnetic induction and by image analysis as a function of the wall height. In addition, the microsections were examined for intermetallic phases and precipitations. Moreover, corrosion tests were carried out according to ASTM G 48, Method A. The results indicate that an increase in arc energy leads to longer t12/8 cooling times. Depending on the filler metal composition, this leads to ferrite contents that are partially outside the values required according to ISO 17781. Furthermore, precipitates of secondary austenite are often found, which is attributed to the multiple reheating by the subsequent layers.

scholarly journals Effect of different variants of filler metal S Ni 6625 on properties and microstructure by additive layer manufactured using CMT process

2021 ◽  
Author(s):  
Manuela Zinke ◽  
Stefan Burger ◽  
Julius Arnhold ◽  
Sven Jüttner
Keyword(s):  
Weld Metal ◽  
Filler Metal ◽  
Welding Process ◽  
Travel Speed ◽  
Cold Metal Transfer ◽  
Thin Walled Structures ◽  
Thin Walled ◽  
Cold Metal ◽  
Hardness Values ◽  
Wire Feed

AbstractThe influence of arc energy and different filler metal composition on the mechanical properties and macro- and microstructure of additively welded thin-walled structures of Ni-based alloy were investigated using four different variants commercially available solid wire electrodes of type S Ni 6625. As the welding process, the Cold Metal Transfer (CMT) process was used. The heat input and cooling rate were varied by adjusting wire feed and travel speed. The results show that an increase in arc energy leads to longer t10/6 cooling times. This leads to an increase in the dendrite arm spacing and thus to a reduction in the strength values and hardness of the thin-walled structures. The higher Fe-containing variant of S Ni 6625 produces the highest strength and hardness values, while the W-alloyed solid wire electrode produces the lowest values. The porosity in the walled structures was very low, and unacceptable weld defects, hot cracks and lack of fusion did not occur. Segregations occur in all weld metal specimens. While niobium, molybdenum and titanium are the preferred segregations in the Nb-alloyed Ni 6625 type weld metal, only Mo is present in the W-alloyed Ni 6660 type weld metal.

scholarly journals Effect of Filler Metal Type on Microstructure and Mechanical Properties of Fabricated NiAl Bronze Alloy Using Wire Arc Additive Manufacturing System

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 513
Author(s):  
Jae Won Kim ◽  
Jae-Deuk Kim ◽  
Jooyoung Cheon ◽  
Changwook Ji
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Additive Manufacturing ◽  
Filler Metal ◽  
Gas Metal Arc Welding ◽  
Metal Wire ◽  
Cold Metal Transfer ◽  
Metal Type ◽  
Cold Metal ◽  
Wire Arc Additive Manufacturing

This study observed the effect of filler metal type on mechanical properties of NAB (NiAl-bronze) material fabricated using wire arc additive manufacturing (WAAM) technology. The selection of filler metal type is must consider the field condition, mechanical properties required by customers, and economics. This study analyzed the bead shape for representative two kind of filler metal types use to maintenance and fabricated a two-dimensional bulk NAB material. The cold metal transfer (CMT) mode of gas metal arc welding (GMAW) was used. For a comparison of mechanical properties, the study obtained three specimens per welding direction from the fabricated bulk NAB material. In the tensile test, the NAB material deposited using filler metal wire A showed higher tensile strength and lower elongation (approx. +71 MPa yield strength, +107.1 MPa ultimate tensile strength, −12.4% elongation) than that deposited with filler metal wire B. The reason is that, a mixture of tangled fine α platelets and dense lamellar eutectoid α + κIII structure with β´ phases was observed in the wall made with filler metal wire A. On the other hand, the wall made with filler metal wire B was dominated by coarse α phases and lamellar eutectoid α + κIII structure in between.

scholarly journals Thermo-Mechanical Modelling of Wire-Arc Additive Manufacturing (WAAM) of Semi-Finished Products

Metals ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 1009 ◽  
Author(s):  
Marcel Graf ◽  
Andre Hälsig ◽  
Kevin Höfer ◽  
Birgit Awiszus ◽  
Peter Mayr
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Additive Manufacturing ◽  
Gas Metal Arc Welding ◽  
Welding Process ◽  
Temperature Fields ◽  
Filler Materials ◽  
Cold Metal Transfer ◽  
Cold Metal ◽  
Wire Arc Additive Manufacturing

Additive manufacturing processes have been investigated for some years, and are commonly used industrially in the field of plastics for small- and medium-sized series. The use of metallic deposition material has been intensively studied on the laboratory scale, but the numerical prediction is not yet state of the art. This paper examines numerical approaches for predicting temperature fields, distortions, and mechanical properties using the Finite Element (FE) software MSC Marc. For process mapping, the filler materials G4Si1 (1.5130) for steel, and AZ31 for magnesium, were first characterized in terms of thermo-physical and thermo-mechanical properties with process-relevant cast microstructure. These material parameters are necessary for a detailed thermo-mechanical coupled Finite Element Method (FEM). The focus of the investigations was on the numerical analysis of the influence of the wire feed (2.5–5.0 m/min) and the weld path orientation (unidirectional or continuous) on the temperature evolution for multi-layered walls of miscellaneous materials. For the calibration of the numerical model, the real welding experiments were carried out using the gas-metal arc-welding process—cold metal transfer (CMT) technology. A uniform wall geometry can be produced with a continuous welding path, because a more homogeneous temperature distribution results.

scholarly journals Influence of post weld heat treatment on tensile properties of cold metal transfer (CMT) arc welded AA6061-T6 aluminium alloy joints

2019 ◽  
Vol 28 (1) ◽  
pp. 135-145 ◽  
Author(s):  
Addanki Ramaswamy ◽  
Sudersanan Malarvizhi ◽  
Visvalingam Balasubramanian
Keyword(s):  
Heat Treatment ◽  
Tensile Properties ◽  
Gas Metal Arc Welding ◽  
Weight Ratio ◽  
Welding Process ◽  
Metal Transfer ◽  
Post Weld Heat Treatment ◽  
Cold Metal Transfer ◽  
Cold Metal ◽  
Weld Heat

AbstractAluminium alloys of 6xxx series are widely used in the fabrication of light weight structures especially, where high strength to weight ratio and excellent weld-ability characteristics are desirable. Gas metal arc welding (GMAW) is the most predominantly used welding process in many industries due to the ease of automation. In this investigation, an attempt has been made to identify the best variant of GMAW process to overcome the problems like alloy segregation, precipitate dissolution and heat affected zone (HAZ) softening. Thin sheets of AA6061-T6 alloy were welded by cold metal transfer (CMT) and Pulsed CMT (PCMT). Among the two joints, the joint made by PCMT technique exhibited superior tensile properties due to the mechanical stirring action in the weld pool caused by forward and rearward movement of the wire along with the controllable diffusion rate at the interface caused by shorter solidification time. However, softening still exists in the welded joints. Further to increase the joint efficiency and to minimize HAZ softening, the joints were subjected to post weld heat treatment (PWHT). Approximately 10% improvement in the tensile properties had been observed in the PWHT joints due to the nucleation of strengthening precipitates in the weld metal and HAZ.

Cold Metal Transfer Spot Joining of AA6061-T6 to Galvanized DP590 Under Different Modes

2015 ◽  
Vol 137 (5) ◽  
Author(s):  
HaiYang Lei ◽  
YongBing Li ◽  
Blair E. Carlson ◽  
ZhongQin Lin
Keyword(s):  
Heat Input ◽  
Mechanical Performance ◽  
Welding Process ◽  
High Strength ◽  
Metal Transfer ◽  
Cold Metal Transfer ◽  
Spot Joining ◽  
Predrilled Hole ◽  
Joint Quality ◽  
Cold Metal

In order to meet the upcoming regulations on greenhouse gas emissions, aluminum use in the automotive industry is increasing. However, this increase is now seen as part of a multimaterial strategy. Consequently, dissimilar material joints are a reality, which poses significant challenges to conventional fusion joining processes. To address this issue, cold metal transfer (CMT) spot welding process was developed in the current study to join aluminum alloy AA6061-T6 as the top sheet to hot dip galvanized (HDG) advanced high strength steel (AHSS) DP590 as the bottom sheet. Three different welding modes, i.e., direct welding (DW) mode, plug welding (PW) mode, and edge plug welding (EPW) mode were proposed and investigated. The DW mode, having no predrilled hole in the aluminum top sheet, required concentrated heat input to melt through the Al top sheet and resulted in a severe tearing fracture, shrinkage voids, and uneven intermetallic compounds (IMC) layer along the faying surface, leading to poor joint properties. Welding with the predrilled hole, PW mode, required significantly less heat input and led to greatly reduced, albeit uneven, IMC layer thickness. However, it was found that the EPW mode could homogenize the welding heat input into the hole and thus produce the most stable welding process and best joint quality. This led to joints having an excellent joint morphology characterized by the thinnest IMC layer and consequently, best mechanical performance among the three modes.

Effect of the CMT advanced process combined with an active cooling technique on macro and microstructural aspects of aluminum WAAM

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Felipe Ribeiro Teixeira ◽  
Fernando Matos Scotti ◽  
Ruham Pablo Reis ◽  
Américo Scotti
Keyword(s):  
Electrical Signal ◽  
Management Technique ◽  
Marginal Effect ◽  
Thin Wall ◽  
Cold Metal Transfer ◽  
Content Type ◽  
Active Cooling ◽  
Cold Metal ◽  
Wire Arc Additive Manufacturing ◽  
Cooling Technique

Purpose This paper aims to assess the combined effect of the Cold Metal Transfer (CMT) advanced process and of a thermal management technique (near immersion active cooling [NIAC]) on the macro and microstructure of Al wall-like preforms built by wire arc additive manufacturing (WAAM). As specific objective, it sought to provide information on the effects of the electrode-positive/electrode-negative (EP/EN) parameter in the CMT advanced process fundamental characteristics. Design/methodology/approach Initially, bead-on-plate deposits were produced with different EP/EN ratios, still keeping the same deposition rate, and the outcomes on the electrical signal traces and bead formation were analyzed. In a second stage, the EP/EN parameter and the layer edge to water distance (LEWD) parameter from the NIAC technique were systematically varied and the resultant macro and microstructures compared with those formed by applying natural cooling. Findings Constraints of EP/EN setting range were uncovered and discussed. The use of the NIAC technique favors the formation of finer grains. For a given EP/EN value, a variation in the NIAC intensity (LEWD value) showed marginal effect on grain size. When the EP/EN parameter effect is isolated, i.e. for a given LEWD setting, it was observed that an increase in the EP/EN level favors coarser grains. Originality/value Both the EP/EN parameter and the use of an active cooling technique (NIAC) might be used, even in combination, as effective tools for achieving proper macro and microstructure in WAAM of thin wall builds.

Studies on cold metal transfer welding of aluminium alloy 6061-T6 using ER 4043

2020 ◽  
Vol 234 (7) ◽  
pp. 924-937
Author(s):  
R Pramod ◽  
N Siva Shanmugam ◽  
CK Krishnadasan
Keyword(s):  
Mechanical Properties ◽  
Aluminium Alloy ◽  
Pressure Vessel ◽  
Weld Zone ◽  
Welding Process ◽  
Metal Transfer ◽  
Welding Parameter ◽  
Cold Metal Transfer ◽  
Cold Metal ◽  
Alloy 6061

Aluminium alloy 6061-T6 is utilized in aerospace industry for developing pressure vessel liner. Cold metal transfer is a promising welding process used in fabricating aluminium structures. The present work is focussed to achieve an optimum welding parameter for joining a 3.5-mm thick pressure vessel and to examine the mechanical properties and metallurgical nature of the weldment. The welded joint was evaluated as defect free using radiography test. The joint efficiency (66.61%) and measured microhardness of weldment (59.78 HV) exhibited promising results. The effect of grain coarsening in the heat affected zone (HAZ) and weld zone is attributed to the thermal gradients during welding. Dissipation of small amounts of strengthening elements Si and Mg during welding leads to reduction in mechanical properties. X-ray diffraction peaks revealed the presence of intermetallic Al–Si and Fe–Si in the weld zone. Fractography examination confirms the ductile type of failure in the fractured surface of the tensile samples.

Sign in / Sign up

Export Citation Format

Share Document