scholarly journals Numerical Model Analysis of Myring–Savonius wind turbines

2019 ◽  
Vol 4 (1) ◽  
pp. 180-185
Author(s):  
M. Saleh ◽  
Ferenc Szodrai
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Primary Objective ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Energy Potential ◽  
Cross Sectional ◽  
Tip Speed Ratio ◽  
Savonius Wind Turbine ◽  
Cfd Method

Nowadays the importance of renewable energy is growing, and the utilization of the low wind energy potential is getting crucial. There are turbines with low and high tip speed ratio. Turbines with low tip speed ratio such as the Savonius wind turbine can generate adequate amount of torque at low wind velocities. These types of turbines are also called drag machines. The geometry of the blade can greatly influence the efficiency of the device. With Computational Fluid Dynamics (CFD) method, several optimizations can be done before the production. In our paper the Savonius wind turbine blade geometry was based on the so-called Myring equation. The primary objective of this paper was to increase the power coefficient by modelling the effect of the wind on the turbine blade. For the sake of simplicity, a 2D cross-sectional area was investigated in the simulation with ANSYS CFX 19.1.

scholarly journals Drag coefficient calculation of modified Myring-Savonius wind turbine with numerical simulations

2020 ◽  
Vol 10 (2) ◽  
pp. 73-84
Author(s):  
Mahmoud Saleh ◽  
Endre Kovács
Keyword(s):  
Drag Coefficient ◽  
Wind Turbine ◽  
Primary Objective ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Energy Potential ◽  
Cross Sectional ◽  
Ansys Fluent ◽  
Tip Speed Ratio ◽  
Savonius Wind Turbine

Nowadays the importance of renewable energy is growing, and the utilization of the low wind energy potential is getting crucial. There are turbines with low and high tip speed ratio. Turbines with low tip speed ratio such as the Savonius wind turbine can generate adequate amount of torque at low wind velocities. These types of turbines are also called drag machines. The geometry of the blade can greatly influence the efficiency of the device. With Computational Fluid Dynamics (CFD) method, several optimizations can be done before the production. In our paper the Savonius wind turbine blade geometry was designed based on the so-called Myring equation. The primary objective of this paper was to investigate the drag coefficient of the force acting on the surface of the blade. Also, the Karman vortex was investigated and the space ratio of that vortex in our simulation was compared to a typical one. The power coefficient of a new Savonius turbine was investigated at different values of top speed ratio (TSR). For the sake of simplicity, a 2D cross-sectional area was investigated in the simulation with ANSYS Fluent 19.2.

scholarly journals Performance assessment and optimization of a helical Savonius wind turbine by modifying the Bach’s section

2021 ◽  
Vol 3 (8) ◽  
Author(s):  
M. Niyat Zadeh ◽  
M. Pourfallah ◽  
S. Safari Sabet ◽  
M. Gholinia ◽  
S. Mouloodi ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Performance Assessment ◽  
Turbulent Flows ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
Basic Model ◽  
Turbine Performance ◽  
Primary Model ◽  
Savonius Wind Turbine

AbstractIn this paper, we attempted to measure the effect of Bach’s section, which presents a high-power coefficient in the standard Savonius model, on the performance of the helical Savonius wind turbine, by observing the parameters affecting turbine performance. Assessment methods based on the tip speed ratio, torque variation, flow field characterizations, and the power coefficient are performed. The present issue was stimulated using the turbulence model SST (k- ω) at 6, 8, and 10 m/s wind flow velocities via COMSOL software. Numerical simulation was validated employing previous articles. Outputs demonstrate that Bach-primary and Bach-developed wind turbine models have less flow separation at the spoke-end than the simple helical Savonius model, ultimately improving wind turbines’ total performance and reducing spoke-dynamic loads. Compared with the basic model, the Bach-developed model shows an 18.3% performance improvement in the maximum power coefficient. Bach’s primary model also offers a 12.4% increase in power production than the initial model’s best performance. Furthermore, the results indicate that changing the geometric parameters of the Bach model at high velocities (in turbulent flows) does not significantly affect improving performance.

Numerical Research on the Characteristics of Lift-Drag Type Vertical Axis Wind Turbine

2012 ◽  
Vol 189 ◽  
pp. 448-452
Author(s):  
Yan Jun Chen ◽  
Guo Qing Wu ◽  
Yang Cao ◽  
Dian Gui Huang ◽  
Qin Wang ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Vertical Axis ◽  
Chord Length ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio ◽  
Middle Range ◽  
Parabolic Form ◽  
Cfd Method

Numerical studies are conducted to research the performance of a kind of lift-drag type vertical axis wind turbine (VAWT) affected by solidity with the CFD method. Moving mesh technique is used to construct the model. The Spalart-Allmaras one equation turbulent model and the implicit coupled algorithm based on pressure are selected to solve the transient equations. In this research, how the tip speed ratio and the solidity of blade affect the power coefficient (Cp) of the small H-VAWT is analyzed. The results indicate that Cp curves exhibit approximate parabolic form with its maximum in the middle range of tip speed ratio. The two-blade wind turbine has the lowest Cp while the three-blade one is more powerful and the four-blade one brings the highest power. With the certain number of blades, there is a best chord length, and too long or too short chord length may reduce the Cp.

Aerodynamic Performance Analysis of a Large Scale Wind Turbine Blade under Variable Condition

2013 ◽  
Vol 291-294 ◽  
pp. 527-530
Author(s):  
Peng Zhan Zhou ◽  
Fang Sheng Tan
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Power ◽  
Turbine Blade ◽  
Large Scale ◽  
Aerodynamic Performance ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
Variable Condition

Based on BLADED software, the aerodynamic performance of a large scale wind turbine blade was analyzed under variable condition. The results show that the rated power of the blade under variable condition is increased 10%, when the rated wind speed is changed from 10.5m/s to 11.0 m/s. The blade’s wind power coefficient is above 0.46, and its tip speed ratio is between 7.8 and 11.4. When its tip speed ratio is 9.5, the blade’s maximum wind power coefficient is 0.486. It is indicated that the blade has good aerodynamic performance and wide scope of wind speed adaptive capacity. The blade root’s equivalent fatigue load is 2.11 MN•m, and its extreme flapwise load is 4.61 MN•m. The loads under variable condition are both less than that of the designed condition, so the blade’s application under variable condition is safe.

Aerodynamic Optimization of a Swept Horizontal Axis Wind Turbine Blade

2021 ◽  
pp. 1-28
Author(s):  
Mehmet Numan Kaya ◽  
Faruk Köse ◽  
Oguz Uzol ◽  
Derek Ingham ◽  
Lin Ma ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Wind Turbine Blade ◽  
Horizontal Axis ◽  
Power Coefficient ◽  
Design Parameters ◽  
Speed Ratio ◽  
Blade Design ◽  
Horizontal Axis Wind Turbine ◽  
Tip Speed Ratio

Abstract The aerodynamic shapes of the blades are still of high importance and various aerodynamic designs have been developed in order to increase the amount of energy production. In this study, a swept horizontal axis wind turbine blade has been optimized to increase the aerodynamic efficiency using the Computational Fluid Dynamics method. To illustrate the technique, a wind turbine with a rotor diameter of 0.94 m has been used as the baseline turbine and the most appropriate swept blade design parameters, namely the sweep start up section, tip displacement and mode of the sweep have been investigated to obtain the maximum power coefficient at the design tip speed ratio. At this stage, a new equation that allows all three swept blade design parameters to be changed independently has been used to design swept blades, and the response surface method has been used to find out the optimum swept blade parameters. According to the results obtained, a significant increase of 4.28% in the power coefficient was achieved at the design tip speed ratio with the new designed optimum swept wind turbine blade. Finally, baseline and optimum swept blades have been compared in terms of power coefficients at different tip speed ratios, force distributions, pressure distributions and tip vortices.

scholarly journals Analysis of Archimedes Spiral Wind Turbine Performance by Simulation and Field Test

Energies ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4624
Author(s):  
Hyeonmu Jang ◽  
Dongmyeong Kim ◽  
Yechan Hwang ◽  
Insu Paek ◽  
Seungjoo Kim ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Field Test ◽  
Maximum Error ◽  
Mechanical Efficiency ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Archimedes Spiral ◽  
Tip Speed Ratio ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method

In this study, the performance of an Archimedes spiral wind turbine is analyzed by simulation and validated by a field test. It is characterized as a horizontal-axis drag-type wind turbine. This type of wind turbine cannot be analyzed by the well-known Blade Element Momentum(BEM) theory or Double Stream Tube Method(DSTM) commonly used to analyze the performance of lift-type wind turbines. Therefore, the computational fluid dynamics (CFD) method was applied. From the simulation, the power coefficient, known as the mechanical efficiency of the rotor, the tip speed ratio was obtained. The maximum power coefficient, and the corresponding tip speed ratio were found to be 0.293 and 2.19, respectively. In addition, the electrical efficiency with respect to the rotational speed of the generator was obtained through generator–controller test. The obtained mechanical and electrical efficiencies were used to predict the power curve of the wind turbine. Finally, the predicted performance of the wind turbine, including the electrical losses, was validated by the field test. The maximum error between the prediction and the measured power was found to be less than 7.80%.

Design & optimization of a small wind turbine blade for operation at low wind speed

2015 ◽  
Vol 12 (1) ◽  
pp. 83-94 ◽  
Author(s):  
Manoj Kumar Chaudhary ◽  
Anindita Roy
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Twist Angle ◽  
Chord Length ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Design Point ◽  
Tip Speed Ratio ◽  
Blade Number ◽  
Selection Of

A small wind turbine blade was designed and optimized in this research paper. The blade plays an important role, because it is the most important part of the energy absorption system. Consequently, the blade has to be designed carefully to enable to absorb energy with its greatest efficiency. The main objective of this paper is to optimized blade number and selection of tip speed ratio corresponding to the solidity. The power performance of small horizontal axis wind turbines was simulated in detail using blade element momentum methods (BEM). In this paper for wind blade design various factors such as tip loss, hub loss, drag coefficient, and wake were considered. The design process includes the selection of the wind turbine type and the determination of the blade airfoil, twist angle distribution along the radius, and chord length distribution along the radius. A parametric study that will determine if the optimized values of blade twist angle and chord length create the most efficient blade geometry. The 3-bladed, 5-bladed and 7-bladed rotor achieved maximum values of Cp 0.46, 0.5 and 0.48 at the tip speed ratio 7, 5 and 4 respectively. It was observed that using BEM theory, maximum Cp varied with strongly solidity and weakly with the blade number. The studies showed that the power coefficient increases upto blade number B = 5, while the blade number if increased above 5 then the power coefficient decreases at operating pitch angle equal to 3°. Highest Cp would have solidity between 4% to 6% for number of blade 3 and design point tip speed ratio of about "7". Highest Cp would have solidity ranging from 5% to 10% for number of blade 5 and 7 and design point tip speed ratio of about 5 and 4 respectively.

scholarly journals 361 Savonius wind turbine with wind concentrator : In case of tip speed ratio>1.0

2005 ◽  
Vol 2005 (0) ◽  
pp. 83-84
Author(s):  
Sheng Zhang ◽  
Takayuki Yaginuma ◽  
Masahiro Mino ◽  
Hiroyuki Ueno ◽  
Susumu Ishii
Keyword(s):  
Wind Turbine ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
Savonius Wind Turbine

Savonius Wind Turbine Performances on Wind Concentrator

2017 ◽  
Vol 8 (1) ◽  
pp. 376
Author(s):  
Dygku. Asmanissa Awg. Osman ◽  
Norzanah Rosmin ◽  
Nor Shahida Hasan ◽  
Baharruddin Ishak ◽  
Aede Hatib Mustaamal@Jamal ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Electrical Power ◽  
Vertical Axis ◽  
Angular Speed ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Air Compressor ◽  
Tip Speed Ratio ◽  
Savonius Wind Turbine ◽  
Air Streams

The air streams from the outlet of an air compressor can be used to generate electricity. For instance, if a micro-sized Vertical-Axis Wind-Turbine (VAWT) is installed towards the airflow, some amount of electricity can be generated before being stored in a battery bank. The research’s objectives are to design, fabricate and analyze the performance of Helical Savonius VAWT blade rotors, which is tested with and without using a wind concentrator. The Helical Savonius VAWT is tested at 0 cm without the concentrator, whereas the blade rotor is tested at concave-blade position when using the concentrator. The blade and the wind concentrator designs were based on the dimensions and the constant airflow of the air compressor. The findings suggested that the blade produced its best performance when tested using wind concentrator at concave-blade position in terms of angular speed (<em>ω</em>), tip speed ratio (<em>TSR</em>) and the generated electrical power (<em>P</em><em><sub>E</sub></em>). The findings concluded that the addition of wind concentrator increases the airflow which then provided better performances on the blades.

Study on Performance and Flow Condition of a Cross-Flow Wind Turbine With a Symmetrical Casing

2011 ◽  
Vol 133 (5) ◽  
Author(s):  
Junichiro Fukutomi ◽  
Toru Shigemitsu ◽  
Hiroki Daito
Keyword(s):  
Wind Turbine ◽  
Rotational Speed ◽  
Flow Condition ◽  
Cross Flow ◽  
Low Noise ◽  
Maximum Power ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
The Cross

A cross-flow wind turbine has a high torque coefficient at a low tip speed ratio. Therefore, it is a good candidate for use as a self-starting turbine. Furthermore, it has low noise and excellent stability; therefore, it has attracted attention from the viewpoint of applications as a small wind turbine for an urban district. However, its maximum power coefficient is extremely low (10%) as compared to that of other small wind turbines. Prevailing winds in two directions often blow in urban and coastal regions. Therefore, in order to improve the performance and the flow condition of the cross-flow rotor, a casing suitable for this sort of prevailing wind conditions is designed in this research and the effect of the casing is investigated by experimental and numerical analysis. In the experiment, a wind tunnel with a square discharge is used and main flow velocity is set as 20 m/s. A torque meter, a rotational speed pickup, and a motor are assembled with the same axis as the test wind turbine and the tip speed ratio is changeable by a rotational speed controller. The casing is set around the cross-flow rotor and flow distribution at the rotor inlet and the outlet is measured by a one-hole pitot tube. The maximum power coefficient is obtained as Cpmax = 0.19 with the casing, however Cpmax = 0.098 without the casing. It is clear that the inlet and the outlet flow condition is improved by the casing. In the present paper, in order to improve the performance of a cross-flow wind turbine, a symmetrical casing suitable for prevailing winds in two directions is proposed. Then, the performance and the internal flow condition of the cross-flow wind turbine with the casing are clarified. Furthermore, the influence of the symmetrical casing on performance is discussed and the relation between the flow condition and performance is considered.

Sign in / Sign up

Export Citation Format

Share Document