Seismic behaviour of cross-shaped steel fibre reinforced concrete columns

2020 ◽  
Vol 20 (4) ◽  
Author(s):  
Linzhu Sun ◽  
Zhengzhen Wei ◽  
Wei Li ◽  
Jinhuai Xiang
Keyword(s):  
Reinforced Concrete ◽  
Steel Fibre ◽  
Concrete Columns ◽  
Fibre Reinforced Concrete ◽  
Seismic Behaviour ◽  
Reinforced Concrete Columns ◽  
Steel Fibre Reinforced Concrete

Numerical study of ultra-high-performance steel fibre–reinforced concrete columns under monotonic push loading

2017 ◽  
Vol 21 (8) ◽  
pp. 1234-1248 ◽  
Author(s):  
Shenchun Xu ◽  
Chengqing Wu ◽  
Zhongxian Liu ◽  
Jun Li
Keyword(s):  
Reinforced Concrete ◽  
Axial Compression ◽  
High Performance ◽  
Steel Fibre ◽  
Concrete Columns ◽  
Fibre Reinforced Concrete ◽  
Structural Behaviour ◽  
Reinforced Concrete Columns ◽  
Steel Fibre Reinforced Concrete ◽  
High Performance Steel

A finite element model is developed to investigate the behaviour of ultra-high-performance steel fibre–reinforced concrete columns under combined axial compression and horizontal monotonic push loading. The effects of steel fibre content, axial compression ratio, reinforcement ratio (or rebar ratio), stirrup ratio and shear span ratio on the structural behaviour of ultra-high-performance steel fibre–reinforced concrete columns are investigated in detail. The numerical model shows good agreement in bond–slip behaviour of specimens based on CEB model results and numerical results, and such behaviour should be taken into consideration in engineering practice. The results indicate that the developed finite element model could predict the structural behaviour and failure mode of ultra-high-performance steel fibre–reinforced concrete columns effectively. It is found that the reinforcement ratio, axial compression ratio, shear span ratio and volume fraction of steel fibre have a great influence on both the structural behaviour and failure modes of specimens.

scholarly journals Seismic behaviour of precast sandwich wall panels of steel fibre reinforced concrete layers and fibre reinforced polymer connectors

2021 ◽  
Vol 237 ◽  
pp. 112149
Author(s):  
Rodrigo Lameiras ◽  
Joaquim A.O. Barros ◽  
Isabel B. Valente ◽  
Elisa Poletti ◽  
Matilde Azevedo ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Steel Fibre ◽  
Fibre Reinforced Concrete ◽  
Seismic Behaviour ◽  
Steel Fibre Reinforced Concrete ◽  
Reinforced Polymer ◽  
Wall Panels ◽  
Fibre Reinforced Polymer ◽  
Sandwich Wall

Adding an expansive agent to increase the toughness of steel fibre reinforced concrete

2019 ◽  
Vol 26 (4) ◽  
pp. 197-208
Author(s):  
Leo Gu Li ◽  
Albert Kwok Hung Kwan
Keyword(s):  
Reinforced Concrete ◽  
Steel Fibre ◽  
The Other ◽  
Fibre Reinforced Concrete ◽  
Test Results ◽  
Compressive Properties ◽  
Shrinkage Cracking ◽  
Steel Fibre Reinforced Concrete ◽  
Expansive Agent ◽  
Concrete Matrix

Previous research studies have indicated that using fibres to improve crack resistance and applying expansive agent (EA) to compensate shrinkage are both effective methods to mitigate shrinkage cracking of concrete, and the additions of both fibres and EA can enhance the other performance attributes of concrete. In this study, an EA was added to fibre reinforced concrete (FRC) to produce concrete mixes with various water/binder (W/B) ratios, steel fibre (SF) contents and EA contents for testing of their workability and compressive properties. The test results showed that adding EA would slightly increase the superplasticiser (SP) demand and decrease the compressive strength, Young’s modulus and Poisson’s ratio, but significantly improve the toughness and specific toughness of the steel FRC produced. Such improvement in toughness may be attributed to the pre-stress of the concrete matrix and the confinement effect of the SFs due to the expansion of the concrete and the restraint of the SFs against such expansion.

Structural performance of steel fibre reinforced concrete — Part IV. Toughness properties

2014 ◽  
Vol 5 (2) ◽  
pp. 119-125
Author(s):  
I. Kovács
Keyword(s):  
Reinforced Concrete ◽  
Steel Fibre ◽  
Fibre Orientation ◽  
Reinforced Concrete Beams ◽  
Fibre Reinforcement ◽  
Fibre Reinforced Concrete ◽  
Flexural Toughness ◽  
Steel Fibre Reinforced Concrete ◽  
Set Up ◽  
Flexural Tests

The present paper of a series deals with the experimental characterisation of flexural toughness properties of structural concrete containing different volume of hooked-end steel fibre reinforcement (75 kg/m3, 150 kg/m3). Third-point flexural tests were carried out on steel fibre reinforced concrete beams having a cross-section of 80 mm × 85 mm with the span of 765 mm, hence the shear span to depth ratio was 3. Beams were sawn out of steel fibre reinforced slab elements (see Part I) in order to take into consideration the introduced privilege fibre orientation (I and II) and the position of the beam (Ba-a, Ba-b, Ba-c) before sawing (see Part I). Flexural toughness properties were determined considering different standard specifications, namely the method of the ASTM (American Standards for Testing Materials), the process of the JSCE (Japan Society of Civil Engineering), and the final proposal of Banthia and Trottier for the post cracking strength. Consequently, behaviour of steel fibre reinforced concrete was examined in bending taking into consideration different experimental parameters such as fibre content, concrete mix proportions, fibre orientation, positions of test specimens in the formwork, while experimental constants were the size of specimens, the type of fibre used and the test set-up and test arrangement.

Sign in / Sign up

Export Citation Format

Share Document