The effects of strain-hardening and strain-rate sensitivity on the transient response of elastic-plastic rings and cylinders

1969 ◽  
Vol 11 (10) ◽  
pp. 825-844 ◽  
Author(s):  
Thomas Duffey ◽  
Raymond Krieg
Keyword(s):  
Strain Rate ◽  
Strain Hardening ◽  
Strain Rate Sensitivity ◽  
Transient Response ◽  
Rate Sensitivity ◽  
Elastic Plastic

Finite Deflections of a Rigid-Viscoplastic Strain-Hardening Annular Plate Loaded Impulsively

1968 ◽  
Vol 35 (2) ◽  
pp. 349-356 ◽  
Author(s):  
Norman Jones
Keyword(s):  
Strain Rate ◽  
Strain Hardening ◽  
Strain Rate Sensitivity ◽  
Annular Plate ◽  
Dominant Role ◽  
Plate Thickness ◽  
Rate Sensitivity ◽  
Finite Deflections ◽  
Analytical Treatment ◽  
Rigid Plastic

A relatively simple analytical treatment of the behavior of a rigid-plastic annular plate subjected to an initial linear impulsive velocity profile is presented. The influence of finite deflections has been included in addition to strain-hardening and strain-rate sensitivity of the plate material. It is shown, for deflections up to the order of twice the plate thickness, that strain-hardening is unimportant, strain-rate sensitivity has somewhat more effect, while membrane forces play a dominant role in reducing the permanent deflections.

Strain rate sensitivity and strain hardening response of DP1000 dual phase steel

2018 ◽  
Vol 115 (5) ◽  
pp. 507
Author(s):  
Onur Çavusoglu ◽  
Hakan Gürün ◽  
Serkan Toros ◽  
Ahmet Güral
Keyword(s):  
Tensile Strength ◽  
Strain Rate ◽  
Strain Hardening ◽  
Strain Rate Sensitivity ◽  
Dual Phase Steel ◽  
Rate Sensitivity ◽  
Dual Phase ◽  
Significant Difference ◽  
Load Carrying ◽  
Hardening Coefficient

In this study, strain hardening and strain rate sensitivity behavior of commercial DP1000 dual phase steel have been examined in detail at temperatures of 25 °C, 100 °C, 200 °C and 300 °C, at strain rates of 0.0016 s−1 and 0.16 s−1. As the strain rate has increased, the yield strength has increased but no significant change in tensile strength and strain hardening coefficient has been observed. As the temperature has increased, the yield and tensile strength has decreased in between 25 and 200 °C but it has showed an increase at 300 °C. The strain hardening coefficient has increased in parallel with temperature increase. It has been seen that the strain rate sensitivity has not been affected by temperature. No significant difference in the hardening rate has appeared in between 25 and 200 °C, but the highest value has been calculated at 300 °C. It has been determined that the fracture behavior has occurred earlier and load carrying capacity on necking has reduced with the increase of strain rate and not significantly affected by temperature.

Strain rate sensitivity of a mild steel at room temperature and strain rates of up to 105s−1

1980 ◽  
Vol 15 (4) ◽  
pp. 201-207 ◽  
Author(s):  
M S J Hashmi
Keyword(s):  
Finite Difference ◽  
Mild Steel ◽  
Strain Rate ◽  
Strain Hardening ◽  
Strain Rate Sensitivity ◽  
Elastic Strain ◽  
Room Temperature ◽  
Numerical Technique ◽  
Rate Sensitivity ◽  
Strain Rates

Experimental results on a mild steel are reported from ballistics tests which gave rise to strain rates of up to 105 s−1. A finite-difference numerical technique which incorporates material inertia, elastic-strain hardening and strain-rate sensitivity is used to establish the strain-rate sensitivity constants p and D in the equation, σ4 = σ1 (1+(∊/D)1/ p). The rate sensitivity established in this study is compared with those reported by other researchers.

Sign in / Sign up

Export Citation Format

Share Document