Strain rate sensitivity and strain hardening response of DP1000 dual phase steel

2018 ◽  
Vol 115 (5) ◽  
pp. 507
Author(s):  
Onur Çavusoglu ◽  
Hakan Gürün ◽  
Serkan Toros ◽  
Ahmet Güral
Keyword(s):  
Tensile Strength ◽  
Strain Rate ◽  
Strain Hardening ◽  
Strain Rate Sensitivity ◽  
Dual Phase Steel ◽  
Rate Sensitivity ◽  
Dual Phase ◽  
Significant Difference ◽  
Load Carrying ◽  
Hardening Coefficient

In this study, strain hardening and strain rate sensitivity behavior of commercial DP1000 dual phase steel have been examined in detail at temperatures of 25 °C, 100 °C, 200 °C and 300 °C, at strain rates of 0.0016 s−1 and 0.16 s−1. As the strain rate has increased, the yield strength has increased but no significant change in tensile strength and strain hardening coefficient has been observed. As the temperature has increased, the yield and tensile strength has decreased in between 25 and 200 °C but it has showed an increase at 300 °C. The strain hardening coefficient has increased in parallel with temperature increase. It has been seen that the strain rate sensitivity has not been affected by temperature. No significant difference in the hardening rate has appeared in between 25 and 200 °C, but the highest value has been calculated at 300 °C. It has been determined that the fracture behavior has occurred earlier and load carrying capacity on necking has reduced with the increase of strain rate and not significantly affected by temperature.

Deformation Behaviors and Constitutive Model of DP1000 under Different Strain Rates

2017 ◽  
Vol 898 ◽  
pp. 810-817 ◽  
Author(s):  
Ran Wei ◽  
Ren Bo Song ◽  
Long Jiang ◽  
Heng Jun Cai
Keyword(s):  
Constitutive Model ◽  
Strain Rate ◽  
Strain Hardening ◽  
Dual Phase Steel ◽  
Constitutive Models ◽  
Rate Sensitivity ◽  
Dual Phase ◽  
Strain Rates ◽  
Deformation Behaviors ◽  
Means Of Transmission

The DP1000 cold-rolled dual phase steel, the thickness of which is 1.2 mm, was required to do the tensile test under nine different strain rates from 10-4 s-1 to 1000 s-1. The mechanical properties and morphologies of the steel were obtained and analyzed. According to the C-J model, the plastic deformation characteristics of dual phase steel under different strain rates were studied. By means of transmission electron microscope (TEM), the morphologies of ferrite and martensite in the dynamic were observed. Finally, the constitutive models of quasi-static and high strain rate were established by using the modified Johnson-Cook model. The results reveal that DP1000 dual phase steel has obvious strain rate sensitivity, and it is a relatively pure ferrite and martensite dual phase structure. There are two stage strain hardenging characteristics in DP1000. In the first stage, the strain hardening ability of ferrite is higher, and the second stage is martensite deformation stage, the strain hardening ability is lower. The modified J-C constitutive model has high fitting effect, and the experimental results are matched with the fitting values.

Finite Deflections of a Rigid-Viscoplastic Strain-Hardening Annular Plate Loaded Impulsively

1968 ◽  
Vol 35 (2) ◽  
pp. 349-356 ◽  
Author(s):  
Norman Jones
Keyword(s):  
Strain Rate ◽  
Strain Hardening ◽  
Strain Rate Sensitivity ◽  
Annular Plate ◽  
Dominant Role ◽  
Plate Thickness ◽  
Rate Sensitivity ◽  
Finite Deflections ◽  
Analytical Treatment ◽  
Rigid Plastic

A relatively simple analytical treatment of the behavior of a rigid-plastic annular plate subjected to an initial linear impulsive velocity profile is presented. The influence of finite deflections has been included in addition to strain-hardening and strain-rate sensitivity of the plate material. It is shown, for deflections up to the order of twice the plate thickness, that strain-hardening is unimportant, strain-rate sensitivity has somewhat more effect, while membrane forces play a dominant role in reducing the permanent deflections.

Strain rate sensitivity of a mild steel at room temperature and strain rates of up to 105s−1

1980 ◽  
Vol 15 (4) ◽  
pp. 201-207 ◽  
Author(s):  
M S J Hashmi
Keyword(s):  
Finite Difference ◽  
Mild Steel ◽  
Strain Rate ◽  
Strain Hardening ◽  
Strain Rate Sensitivity ◽  
Elastic Strain ◽  
Room Temperature ◽  
Numerical Technique ◽  
Rate Sensitivity ◽  
Strain Rates

Experimental results on a mild steel are reported from ballistics tests which gave rise to strain rates of up to 105 s−1. A finite-difference numerical technique which incorporates material inertia, elastic-strain hardening and strain-rate sensitivity is used to establish the strain-rate sensitivity constants p and D in the equation, σ4 = σ1 (1+(∊/D)1/ p). The rate sensitivity established in this study is compared with those reported by other researchers.

scholarly journals Dynamic Tensile Properties of CFRP Manufactured by PCM and WCM: Effect of Strain Rate and Configurations

Crystals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1491
Author(s):  
Yujin Yang
Keyword(s):  
Tensile Strength ◽  
Strain Rate ◽  
Tensile Properties ◽  
Strain Rate Sensitivity ◽  
Failure Strain ◽  
Dynamic Performance ◽  
Rate Sensitivity ◽  
Fracture Mechanisms ◽  
Reinforced Plastic ◽  
Dynamic Tensile Properties

Carbon fiber-reinforced plastic (CFRP) is a promising material to achieve lightweight automotive components. The effects of the strain rate and configurations of CFRP on dynamic tensile properties have not yet been fully explored; thus, its lightweight benefits cannot be maximized. In this paper, the dynamic tensile properties of CFRPs, tested using two different processes with two different resins and four different configurations, were studied with a strain rate from 0.001 to 500 s−1. The tensile strength, modulus, failure strain, and fracture mechanism were analyzed. It was found that the dynamic performance enhances the strength and modulus, whereas it decreases the failure strain. The two processes demonstrated the same level of tensile strength but via different fracture mechanisms. Fiber orientation also significantly affects the fracture mode of CFRP. Resins and configurations both have an influence on strain rate sensitivity. An analytic model was proposed to examine the strain rate sensitivity of CFRPs with different processes and configurations. The proposed model agreed well with the experimental data, and it can be used in simulations to maximize the lightweight properties of CFRP.

Sign in / Sign up

Export Citation Format

Share Document