Factors affecting the flow behavior of soil allophane suspensions under low shear rates

1985 ◽  
Vol 104 (2) ◽  
pp. 398-408 ◽  
Author(s):  
Norman Wells ◽  
Benny K.G Theng
Author(s):  
Ravi Arora ◽  
Eric Daymo ◽  
Anna Lee Tonkovich ◽  
Laura Silva ◽  
Rick Stevenson ◽  
...  

Emulsion formation within microchannels enables smaller mean droplet sizes for new commercial applications such as personal care, medical, and food products among others. When operated at a high flow rate per channel, the resulting emulsion mixture creates a high wall shear stress along the walls of the narrow microchannel. This high fluid-wall shear stress of continuous phase material past a dispersed phase, introduced through a permeable wall, enables the formation of small emulsion droplets — one drop at a time. A challenge to the scale-up of this technology has been to understand the behavior of non-Newtonian fluids under high wall shear stress. A further complication has been the change in fluid properties with composition along the length of the microchannel as the emulsion is formed. Many of the predictive models for non-Newtonian emulsion fluids were derived at low shear rates and have shown excellent agreement between predictions and experiments. The power law relationship for non-Newtonian emulsions obtained at low shear rates breaks down under the high shear environment created by high throughputs in small microchannels. The small dimensions create higher velocity gradients at the wall, resulting in larger apparent viscosity. Extrapolation of the power law obtained in low shear environment may lead to under-predictions of pressure drop in microchannels. This work describes the results of a shear-thinning fluid that generates larger pressure drop in a high-wall shear stress microchannel environment than predicted from traditional correlations.


1979 ◽  
Vol 52 (3) ◽  
pp. 676-691 ◽  
Author(s):  
E. A. Collins ◽  
D. J. Hoffmann ◽  
P. L. Soni

Abstract The viscosity of PVC plastisols is seen to be affected by numerous variables. Increase in concentration of the resin causes the viscosity to rise, with the increase being more abrupt at the higher concentrations. Deviation from Newtonian behavior also increases with concentration. Decrease in the size of particles results in an increase in viscosity, the effect being more pronounced at low shear rates. Broadening the distribution of particle sizes results in a decrease in viscosity. Porous particles yield plastisols with higher viscosity as compared to nonporous compact particles. The type of plasticizer also affects the viscosity. A plasticizer which is a better solvent for PVC (low value of polymer-solvent interaction parameter, χ) results in a higher viscosity due to an increase in the amount of dissolved polymer. Additives such as alcohols and soaps affect the viscosity in an, as yet, unknown way. Fillers, heat stabilizers, and pigments also increase the viscosity. With increasing temperature, the viscosity first decreases, passes through a minimum and then increases until gelation. With further rise in temperature the viscosity again decreases and then levels out before degradation occurs. In future work, particular emphasis needs to be given to the understanding of the basic mechanism involved in the effect of additives on the flow behavior. Systematic experiments with a range of well-defined particle sizes and over a wide range of shear rates are also needed. A better understanding of the factors affecting the behavior of plastisols will go a long way in changing the art of plastisol formulation to a science.


1969 ◽  
Vol 42 (5) ◽  
pp. 1321-1335
Author(s):  
William G. DePierri ◽  
J. R. Hopper

Abstract Factors affecting the flow properties of EPDM compounds have been studied and the findings of the study applied to the injection molding of these compounds. The level of oil and of black were found to change the flow properties of EPDM compounds. Higher levels of oil decreased the compound viscosity while higher levels of black increased the compound viscosity. The viscosity of the oil influenced compound viscosities. Compounds made with the more viscous (at 210° F) oil had slightly higher viscosities. However, changing from an aromatic to a naphthenic oil of similar viscosity had little effect on the compound viscosity. Compounds made from two different polymers of similar Mooney viscosity were found to have widely divergent flow behavior at high shear rates. Injection molding of EPDM compounds was studied with a molding assembly which had a capillary rheometer as barrel and plunger. Injection pressure data from the molding experiments was found to parallel closely the rheological data. An analysis of the pressure drops in passing through different parts of the mold assembly was made. The total calculated pressure drop agreed closely with the measured pressure drop. The viscous generation of heat was found to be proportional to pressure drop, and an equation is presented which relates the temperature increase to the pressure drop.


2020 ◽  
Vol 18 (2) ◽  
pp. 117
Author(s):  
Afni Restasari ◽  
Luthfia Hajar Abdillah ◽  
Retno Ardianingsih ◽  
Rika Suwana Budi

HTPB is the ultimate component of matrix builder for high-filled composite materials. Flow behavior of HTPB in low shear is crucial in casting the composite. Considering the characteristics of hydrocarbon, this work aims to investigate the effect of microstructure composition of HTPB on its flow behavior. In this work, HTPB with different composition of 1,4-cis, 1,2-vinyl and 1,4-trans microstructures were used. Fourier-Transform Infra-Red spectroscopy (FT-IR) was used to determine the composition. It was calculated as a ratio of peak area of 710, 910 and 970 cm-1 for 1,4-cis, 1,2-vinyl, 1,4-trans isomers respectively. Viscosity was measured using a rotational viscometer at various low shear rates. It is found that HTPB with high 1,2-vinyl/1,4-trans isomers shows shear thickening behaviour, distinguished significantly from Newtonian flow of the others. It is suggested that mechanism of shear thickening involves a certain configuration of 1,2-vinyl and 1,4-trans isomers that builds different degrees of flow resistance from one to other shear layers. The configuration and flow resistance changes among layers as shear increases.


Author(s):  
Scott C. Corbett ◽  
Amin Ajdari ◽  
Ahmet U. Coskun ◽  
Hamid N.-Hashemi

Thrombosis and hemolysis are two problems encountered when processing blood in artificial organs. Physical factors of blood flow alone can influence the interaction of proteins and cells with the vessel wall, induce platelet aggregation and influence coagulation factors responsible for the formation of thrombus, even in the absence of chemical factors in the blood. These physical factors are related to the magnitude of the shear rate/stress, the duration of the applied force and the local geometry. Specifically, high blood shear rates (or stress) lead to damage (hemolysis, platelet activation), while low shear rates lead to stagnation and thrombosis [1].


Blood ◽  
2014 ◽  
Vol 124 (21) ◽  
pp. 2716-2716
Author(s):  
Vivien A. Sheehan ◽  
Sheryl Nelson ◽  
Caroline Yappan ◽  
Bogdan R. Dinu ◽  
Danielle Guffey ◽  
...  

Abstract Background: Sickle cell disease (SCD) patients have altered blood rheology due to erythrocyte abnormalities, including increased aggregation and reduced deformability, which together affect microcirculatory blood flow and tissue perfusion. At equal hematocrit, sickle cell blood viscosity is increased compared to normal individuals. The hematocrit to viscosity ratio (HVR) is a measure of red blood cell (RBC) oxygen carrying capacity, and is reduced in SCD with clinical consequences related to altered blood flow and reduced tissue oxygenation. Erythrocyte transfusions reduce HVR at low shear rates that mimic venous circulation, and do not change HVR at high shear rates that mimic arterial blood flow. Hydroxyurea is a safe and effective therapy for SCD; however, its effects on sickle cell rheology and HVR have not been fully investigated. Evaluating the effects of hydroxyurea on viscosity is especially critical, before its use is extended widely to patients with cerebrovascular disease or genotypes with higher hematocrit and higher viscosity such as Hemoglobin SC (HbSC). Methods: To determine the effects of hydroxyurea on viscosity and HVR, we designed a prospective study to measure whole blood viscosity at 45 s-1 (low shear) and 225 s-1(high shear) rates in pediatric patients with SCD using a Brookfield cone and plate viscometer under oxygenated conditions. Venous blood samples (1-3mL) were collected in EDTA and analyzed no more than 4 hours after phlebotomy; samples were run in duplicate by persons blinded to the patient’s sickle genotype and treatment status. Laboratory values were obtained using an ADVIA hematology analyzer. Samples were analyzed from three non-overlapping cohorts of patients with SCD and HbAA individuals for comparison: untreated HbSS patients (n= 43), HbSS patients treated with hydroxyurea at maximum tolerated dose (n=98), untreated HbSC patients (n=53) and HbAA patients (n=19). Laboratory parameters that differed significantly among the SCD groups were analyzed by simple linear regression. Results: Patient characteristics and viscosity measurements are shown in the Table. Within the SCD population, the viscosity was lowest among the untreated HbSS patients, presumably due to their low hematocrit, while viscosity was higher in HbSS patients on hydroxyurea and HbSC patients. When the HVR was calculated for each group, no significant difference was identified between untreated HbSS and untreated HbSC patients. However, hydroxyurea treatment significantly increased HVR at both 45s-1 and 225 s-1 (p<0.001), indicating that the slightly increased viscosity in this cohort was more than compensated by a higher hematocrit. Correlations were tested for hemoglobin (Hb), mean corpuscular volume (MCV), white blood cell count (WBC), absolute neutrophil count (ANC), absolute reticulocyte count (ARC), % fetal hemoglobin (HbF), and average red cell density in g/dL with HVR, at both shear rates. The hydroxyurea-associated HVR increase at both shear rates was independent of %HbF or MCV, but the increased HVR at 225 s-1was associated with lower WBC (p<0.001), lower ANC (p=0.002), and lower red cell density (p=.009). Conclusions: We provide prospective data on whole blood viscosity measurements in a large cohort of children with SCD. Hydroxyurea increases the hematocrit in HbSS patients more than the viscosity, and thus improves HVR. These findings imply that hydroxyurea improves RBC oxygen transport at both high and low shear rates, which should confer clinical benefits, and these effects are independent of HbF induction. Concerns about hydroxyurea increasing whole blood viscosity and reducing tissue oxygenation in children with cerebrovascular disease or HbSC patients may not be warranted, if the same beneficial HVR effects are achieved. Abstract 2717. Table 1. Patient characteristics. Viscosity was typically measured in duplicate and averaged for each patient. HVR at 45 s-1 and 225s-1 was calculated as hematocrit/viscosity. Results are presented as mean ± 2SD. HbAAn=19 HbSS, untreatedn=43 HbSS, on Hydroxyurean=98 HbSCn=53 Age (years) 15.4 ± 3.8 10.4 ± 5.1 10.7 ± 3.4 10.5 ± 4.3 Hemoglobin (gm/dL) 13.5 ± 1.7 8.5 ± 1.0 9.9 ± 1.4 11.0 ± 1.2 Hematocrit (%) 40.9 ± 5.3 25.5 ± 3.1 28.4 ± 3.7 31.3 ± 3.2 Viscosity (cP) at 45s-1 5.3 ± 0.9 4.6 ± 1.2 4.3 ± 0.9 5.5 ±0.9 HVR at 45s-1 7.5 ± 0.9 5.8 ± 1.1 6.75 ± 1.0 5.77 ± 0.7 Viscosity (cP) at 225s-1 3.8 ± 0.5 3.3 ± 0.5 3.4 ± 0.5 4.1 ± 0.5 HVR at 225s-1 10.3 ± 0.7 7.7 ± 0.8 8.53 ± 0.8 7.72 ± 0.6 Disclosures Off Label Use: Hydroxyurea is not FDA approved for use in pediatric sickle cell patients.


2021 ◽  
Vol 15 (3) ◽  
pp. 181-190
Author(s):  
Elif H Ozcan Cetin ◽  
Mehmet S Cetin ◽  
Mustafa B Ozbay ◽  
Hasan C Könte ◽  
Nezaket M Yaman ◽  
...  

Aim: We aimed to assess the association of whole blood with thromboembolic milieu in significant mitral stenosis patients. Methodology & results: We included 122 patients and classified patients into two groups as having thrombogenic milieu, thrombogenic milieu (+), otherwise patients without thrombogenic milieu, thrombogenic milieu (-). Whole blood viscosity (WBV) in both shear rates were higher in thrombogenic milieu (+) group comparing with thrombogenic milieu (-). WBV at high shear rate and WBV at low shear rate parameters were moderately correlated with grade of spontaneous echo contrast. Adjusted with other parameters, WBV parameters at both shear rates were associated with presence of thrombogenic milieu. Discussion & conclusion: We found that extrapolated WBV at both shear rates was significantly associated with the thrombogenic milieu in mitral stenosis. This easily available parameter may provide additional perspective about thrombogenic diathesis.


Author(s):  
Moncef Nehdi ◽  
Sidney Mindess

The emergence of new special concretes on construction sites has shown that concretes of the same slump may behave quite differently on the job. For these concretes, one cannot rely on the traditional workability tests for quality control and rheological characterization. It has been claimed that the flow behavior of fresh concrete closely approximates the Bingham model and that at least two parameters are therefore needed to describe its rheology. Thus, rheological measurements must be carried out at not fewer than two shear rates. This study examines the applicability of the Bingham model to fluid and self-leveling highstrength concrete (HSC). Results obtained from a rheometer are compared with results of the standard slump test. Fluid concrete mixtures were investigated that had a water/binder ratio ( w/ b) of 0.33 and slump values of 200 ± 20 mm and incorporated proportions of limestone filler, silica fume, and ground silica as partial replacement (by volume) of cement. In addition, self-leveling concrete mixtures (torque viscosity ≤ 1 Nm at 15 min) having a w/ b ratio of 0.25 and 15 percent replacement of cement by various fillers were examined. The possibility of characterizing the rheology of fluid and self-leveling HSC on the basis of only two tests carried out at two different shear rates was addressed. An effort was made to define which is more relevant in a rheometer flow curve: the ascending part, the descending part, the maximum stress requirement, the flow resistance, the torque viscosity, or combinations of these factors. The possibility of measuring the rapid stiffening behavior of fresh HSC with time and the effect of ultrafine particles on the rheology using rheometric tests were also investigated.


Sign in / Sign up

Export Citation Format

Share Document