VII-2 High efficiency energy conversion control for tide wave energy converter with pendulum

1985 ◽  
Vol 12 (6) ◽  
pp. 594
Author(s):  
Yasuhiko Dote ◽  
Kenji Yano
Keyword(s):  
Energy Conversion ◽  
Wave Energy ◽  
High Efficiency ◽  
Wave Energy Converter ◽  
Energy Converter

scholarly journals Design and Analysis for a Floating Oscillating Surge Wave Energy Converter

2014 ◽  
Author(s):  
Yi-Hsiang Yu ◽  
Ye Li ◽  
Kathleen Hallett ◽  
Chad Hotimsky
Keyword(s):  
Energy Conversion ◽  
Structure Analysis ◽  
Wave Energy ◽  
Integrated Design ◽  
Design Strategy ◽  
Wave Energy Converter ◽  
Wave Energy Conversion ◽  
Power Performance ◽  
Energy Converter ◽  
The Cost

This paper presents a recent study on the design and analysis of an oscillating surge wave energy converter (OSWEC). A successful wave energy conversion design requires balance between the design performance and cost. The cost of energy is often used as the metric to judge the design of the wave energy conversion (WEC) system, which is often determined based on the device’s power performance; the cost of manufacturing, deployment, operation, and maintenance; and environmental compliance. The objective of this study is to demonstrate the importance of a cost-driven design strategy and how it can affect a WEC design. A set of three oscillating surge wave energy converter designs was analyzed and used as examples. The power generation performance of the design was modeled using a time-domain numerical simulation tool, and the mass properties of the design were determined based on a simple structure analysis. The results of those power performance simulations, the structure analysis, and a simple economic assessment were then used to determine the cost-efficiency of selected OSWEC designs. Finally, we present a discussion on the environmental barrier, integrated design strategy, and the key areas that need further investigation.

Design and Hydrodynamic Performance Testing of One-Base Multi-Buoy Floating Sharp Eagle Wave Energy Converter

2015 ◽  
Vol 1092-1093 ◽  
pp. 152-157
Author(s):  
Zhen Peng Wang ◽  
Ya Ge You ◽  
Ya Qun Zhang ◽  
Song Wei Sheng ◽  
Hong Jun Lin
Keyword(s):  
Wave Energy ◽  
High Efficiency ◽  
Performance Testing ◽  
Clean Energy ◽  
Wave Energy Converter ◽  
Hydrodynamic Performance ◽  
Wave Direction ◽  
Energy Converter ◽  
Working Principle ◽  
Period Wave

Research on wave energy extraction has been conducted in many countries to meet the growing demand for clean energy. To find an efficient and economic way to convert wave energy, an one-base multi-buoy offshore floating Sharp Eagle wave energy converter is designed, consisting of four Eagle head absorbing buoys, one semi-submersible barge, one energy conversion system, buoyancy tanks, underwater appendages and other components. The working principle of the device is described in this paper. To test the hydrodynamic performance of device and make an initial evaluation for the design, a model experiment of 1/13.78th scale was carried out. The influence of wave period, wave height, pressure in hydrocylinders and wave direction is tested. All the efficiencies in different conditions are compared with each other, while the high efficiency and stability of device are verified.

scholarly journals Effective Mooring Rope Tension in Mechanical and Hydraulic Power Take-Off of Wave Energy Converter

2021 ◽  
Vol 13 (17) ◽  
pp. 9803
Author(s):  
Ji Woo Nam ◽  
Yong Jun Sung ◽  
Seong Wook Cho
Keyword(s):  
Energy Conversion ◽  
Wave Energy ◽  
Mechanical Energy ◽  
Electrical Energy ◽  
Energy Conversion Efficiency ◽  
Wave Energy Converter ◽  
Hydraulic Motor ◽  
Energy Converter ◽  
The Individual ◽  
Conversion Efficiencies

The InWave wave energy converter (WEC), which is three-tether WEC type, absorbs wave energy via moored cylindrical buoys with three ropes connected to a terrestrial power take-off (PTO) through a subsea pulley. In this study, a simulation study was conducted to select a suitable PTO when designing a three-tether WEC. The mechanical PTO transfers energy from the buoy to the generator using a gearbox, whereas the hydraulic PTO uses a hydraulic pump, an accumulator, and a hydraulic motor to convert mechanical energy into electrical energy. The hydraulic PTO has a lower energy conversion efficiency than that of the mechanical PTO owing to losses resulting from pipe friction and the individual efficiencies of the hydraulic pumps and motors. However, the efficiencies mentioned above are not the efficiency of the whole system. The efficiency of the whole system should be analyzed considering the tension of the rope and the efficiency of the generator. In this study, the energy conversion efficiencies of the InWave WEC installed the mechanical and hydraulic PTO devices are compared, and their behaviors are analyzed through numerical simulations. The mechanics of mechanical and hydraulic PTO applied to InWave are mathematically expressed, and the issues of the elements constituting the PTO are explained. Finally, factors to consider for PTO selection are presented.

Design and Performance Analysis of Anchor System for a Single-Body Wave Energy Converter

2016 ◽  
Author(s):  
Rodrigo L. Banos ◽  
Hirpa G. Lemu
Keyword(s):  
Power Generation ◽  
Energy Conversion ◽  
Wave Energy ◽  
Wave Energy Converter ◽  
Wave Energy Conversion ◽  
Energy Converter ◽  
Practical Solution ◽  
Simulation Tools ◽  
Anchor System ◽  
Single Body

The last couple of decades have observed an increasing interest in development of wave energy conversion technology for both research and commercial purposes. Though slow due to several reasons, the technology shows an evident progress. Because of the oil crisis facing the energy sector in particular, wave energy is currently seen as a good alternative to fossil fuel based power generation. This has marked its footprints on rising industrial ventures in wave energy based power generation and the search for new devices is gearing up. Among the latest invented models, point wave energy converters are attractive and low investment options. These devices are much smaller than the traditional oscillating water column devices and have good performance when combined in arrays of devices, thus placing the technology in the center of industrial and academic research. This article reports the study conducted to understand the mechanics of the energy exchange in a single-body point wave energy converter device model Cape Verde, patented by the Norwegian company Euro Wave Energy. Furthermore, the article intends to give a practical solution for the design of the anchoring problem in the device. In general, the article attempts to present two completely different objectives: an academic part focusing on understanding the wave energy conversion mechanics, and the industrial development part that attempts to find a practical solution for a particular part of the device. The first step involves establishing a model that describes the motion and potential of absorbance of a conic single-body absorber. The anchor system was designed in accordance with standards provided by Det Norske Veritas, the Norwegian regulatory framework. A quasi-static method is used to calculate the load that the absorber would suffer and a pulley and cable system is proposed to drive these loads to the anchor system. After a review of the different solutions offered for offshore facilities at the present time, the model of a suction anchor is chosen. As design verification through physical testing of prototypes of conversion devices is demanding and costly, various simulation tools are appearing in the field. The application range of some of these different simulation tools has been evaluated and reported in this article.

scholarly journals A Set-Up of 7 Laser Triangulation Sensors and a Draw-Wire Sensor for Measuring Relative Displacement of a Piston Rod Mechanical Lead-Through Transmission in an Offshore Wave Energy Converter on the Ocean Floor

2012 ◽  
Vol 2012 ◽  
pp. 1-32 ◽  
Author(s):  
E. Strömstedt ◽  
O. Svensson ◽  
M. Leijon
Keyword(s):  
Energy Conversion ◽  
Measurement System ◽  
Wave Energy ◽  
Relative Displacement ◽  
Operating Conditions ◽  
Wave Energy Converter ◽  
Laser Triangulation ◽  
Energy Converter ◽  
Set Up ◽  
Offshore Wave

A concept for offshore wave energy conversion is being developed at the Swedish Centre for Renewable Electric Energy Conversion at Uppsala University in Sweden. The wave energy converter (WEC) in focus contains a piston rod mechanical lead-through transmission for transmitting the absorbed mechanical wave energy through the generator capsule wall while preventing seawater from entering the capsule. A set-up of 7 laser triangulation sensors has been installed inside the WEC to measure relative displacement of the piston rod and its corresponding seal housing. A draw-wire sensor has also been set up to measure translator position and the axial displacement of the piston rod. The paper gives a brief introduction to the Lysekil research site, the WEC concept, and the direct drive of WEC prototype L2. A model of operation for the piston rod mechanical lead-through transmission is given. The paper presents sensor choice, configuration, adaptation, mounting, and measurement system calibration along with a description of the data acquisition system. Results from 60 s measurements of nominal operation two months apart with centered moving averages are presented. Uncertainty and error estimations with statistical analyses and signal-to-noise ratios are presented. Conclusions are drawn on the relative motions of the piston rod and the seal housing under normal operating conditions, and an assessment of the applicability of the measurement system is made.

Sign in / Sign up

Export Citation Format

Share Document