Building Heating and Cooling

Solar Energy ◽  
1975 ◽  
pp. 232-255
Keyword(s):  
Heating And Cooling

Exergoeconomic analysis of renewable multi-generation system

2020 ◽  
pp. 99-111
Author(s):  
Vontas Alfenny Nahan ◽  
Audrius Bagdanavicius ◽  
Andrew McMullan
Keyword(s):  
Capital Investment ◽  
Combined Cycle ◽  
Asian Countries ◽  
Generation System ◽  
Integrated Gasification Combined Cycle ◽  
Heating And Cooling ◽  
Integrated Gasification ◽  
Exergoeconomic Analysis ◽  
Main Components ◽  
The Cost

In this study a new multi-generation system which generates power (electricity), thermal energy (heating and cooling) and ash for agricultural needs has been developed and analysed. The system consists of a Biomass Integrated Gasification Combined Cycle (BIGCC) and an absorption chiller system. The system generates about 3.4 MW electricity, 4.9 MW of heat, 88 kW of cooling and 90 kg/h of ash. The multi-generation system has been modelled using Cycle Tempo and EES. Energy, exergy and exergoeconomic analysis of this system had been conducted and exergy costs have been calculated. The exergoeconomic study shows that gasifier, combustor, and Heat Recovery Steam Generator are the main components where the total cost rates are the highest. Exergoeconomic variables such as relative cost difference (r) and exergoeconomic factor (f) have also been calculated. Exergoeconomic factor of evaporator, combustor and condenser are 1.3%, 0.7% and 0.9%, respectively, which is considered very low, indicates that the capital cost rates are much lower than the exergy destruction cost rates. It implies that the improvement of these components could be achieved by increasing the capital investment. The exergy cost of electricity produced in the gas turbine and steam turbine is 0.1050 £/kWh and 0.1627 £/kWh, respectively. The cost of ash is 0.0031 £/kg. In some Asian countries, such as Indonesia, ash could be used as fertilizer for agriculture. Heat exergy cost is 0.0619 £/kWh for gasifier and 0.3972 £/kWh for condenser in the BIGCC system. In the AC system, the exergy cost of the heat in the condenser and absorber is about 0.2956 £/kWh and 0.5636 £/kWh, respectively. The exergy cost of cooling in the AC system is 0.4706 £/kWh. This study shows that exergoeconomic analysis is powerful tool for assessing the costs of products.

Optimization of the time the chromatograph thermostats exit to a given temperature

2020 ◽  
pp. 40-45
Author(s):  
Nadezhda O. Vzduleva ◽  
Valery B. Gitlin
Keyword(s):  
Heating Rate ◽  
Entire Range ◽  
Gas Chromatograph ◽  
Heating And Cooling ◽  
Operating Temperatures ◽  
The Stability

The problems of ensuring the stability of the temperature of the chromatographic experiment carried out using a serial gas chromatograph LGH-3000 are considered. Limiting the permissible heating rate of the chromatograph thermostats does not allow a quick transition to the new conditions of the chromatographic experiment in accordance with the requirements of the technical conditions. The processes of heating and cooling the thermostat are analyzed. It is shown that the ratio of the duration of the interval equal to the sum of the durations of the heating and cooling intervals to the duration of the heating interval is inversely proportional to the temperature of the chromatographic experiment. Based on this situation, an empirical algorithm is proposed for heating the thermostat to a given temperature, which made it possible to reduce the time it takes to reach a given temperature in the entire range of operating temperatures.

INFLUENCE THE QUENCHING AND TEMPERING ON THE MICROSTRUCTURE, MECHANICAL PROPERTIES AND SURFACE ROUGHNESS, OF MEDIUM CARBON STEEL

2018 ◽  
Vol 18 (1) ◽  
pp. 125-135
Author(s):  
Sattar H A Alfatlawi
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Surface Roughness ◽  
Carbon Steel ◽  
Cold Water ◽  
Medium Carbon Steel ◽  
Medium Carbon ◽  
Heating And Cooling ◽  
Treatment Processes ◽  
Quenching And Tempering

One of ways to improve properties of materials without changing the product shape toobtain the desired engineering applications is heating and cooling under effect of controlledsequence of heat treatment. The main aim of this study was to investigate the effect ofheating and cooling on the surface roughness, microstructure and some selected propertiessuch as the hardness and impact strength of Medium Carbon Steel which treated at differenttypes of heat treatment processes. Heat treatment achieved in this work was respectively,heating, quenching and tempering. The specimens were heated to 850°C and left for 45minutes inside the furnace as a holding time at that temperature, then quenching process wasperformed in four types of quenching media (still air, cold water (2°C), oil and polymersolution), respectively. Thereafter, the samples were tempered at 200°C, 400°C, and 600°Cwith one hour as a soaking time for each temperature, then were all cooled by still air. Whenthe heat treatment process was completed, the surface roughness, hardness, impact strengthand microstructure tests were performed. The results showed a change and clearimprovement of surface roughness, mechanical properties and microstructure afterquenching was achieved, as well as the change that took place due to the increasingtoughness and ductility by reducing of brittleness of samples.

Heat Gains, Heating and Cooling in Nordic Housing with Electrical Space Heating

2015 ◽  
Vol 10 (5) ◽  
pp. 599
Author(s):  
Cristina E. Molina ◽  
Matti Lehtonen ◽  
Merkebu Degefa
Keyword(s):  
Space Heating ◽  
Heating And Cooling

Mine water as a resource: space heating and cooling via use of heat pumps

2003 ◽  
Vol 11 (2) ◽  
pp. 191-198 ◽  
Author(s):  
David Banks ◽  
Helge Skarphagen ◽  
Robin Wiltshire ◽  
Chris Jessop
Keyword(s):  
Mine Water ◽  
Heat Pumps ◽  
Space Heating ◽  
Heating And Cooling ◽  
Resource Space

POTOMAC

Alloy Digest ◽  
1975 ◽  
Vol 24 (8) ◽  
Keyword(s):  
Fracture Toughness ◽  
High Temperature ◽  
Heat Treating ◽  
General Purpose ◽  
Low Carbon ◽  
Repeated Heating ◽  
Temperature Changes ◽  
Heating And Cooling ◽  
Temperature Performance ◽  
Heat Checking

Abstract POTOMAC is a general-purpose, low-carbon, chromium-molybdenum-tungsten hot-work steel. It has excellent resistance to shock and heat checking after repeated heating and cooling. Potomac is suitable for hot-work applications involving severe conditions of shock and sudden temperature changes. This datasheet provides information on composition, physical properties, hardness, and tensile properties as well as fracture toughness. It also includes information on high temperature performance as well as forming, heat treating, and machining. Filing Code: TS-290. Producer or source: Allegheny Ludlum Corporation.

Sign in / Sign up

Export Citation Format

Share Document