A new strain-rate-induced deformation mechanism of Cu nanowire: Transition from dislocation nucleation to phase transformation

2015 ◽  
Vol 85 ◽  
pp. 191-198 ◽  
Author(s):  
Hongxian Xie ◽  
Fuxing Yin ◽  
Tao Yu ◽  
Guanghong Lu ◽  
Yongguang Zhang
Keyword(s):  
Phase Transformation ◽  
Strain Rate ◽  
Deformation Mechanism ◽  
Dislocation Nucleation

scholarly journals The Strain Rate Sensitivity and Creep Behavior for the Tripler Plane of Potassium Dihydrogen Phosphate Crystal by Nanoindentation

Micromachines ◽  
2021 ◽  
Vol 12 (4) ◽  
pp. 369
Author(s):  
Jianhui Mao ◽  
Wenjun Liu ◽  
Dongfang Li ◽  
Chenkai Zhang ◽  
Yi Ma
Keyword(s):  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Creep Deformation ◽  
Potassium Dihydrogen Phosphate ◽  
Rate Sensitivity ◽  
Dislocation Nucleation ◽  
Machining Process ◽  
Dihydrogen Phosphate ◽  
Potassium Dihydrogen ◽  
Kdp Crystals

As an excellent multifunctional single crystal, potassium dihydrogen phosphate (KDP) is a well-known, difficult-to-process material for its soft-brittle and deliquescent nature. The surface mechanical properties are critical to the machining process; however, the characteristics of deformation behavior for KDP crystals have not been well studied. In this work, the strain rate effect on hardness was investigated on the mechanically polished tripler plane of a KDP crystal relying on nanoindentation technology. By increasing the strain rate from 0.001 to 0.1 s−1, hardness increased from 1.67 to 2.07 GPa. Hence, the strain rate sensitivity was determined as 0.053, and the activation volume of dislocation nucleation was 169 Å3. Based on the constant load-holding method, creep deformation was studied at various holding depths at room temperature. Under the spherical tip, creep deformation could be greatly enhanced with increasing holding depth, which was mainly due to the enlarged holding strain. Under the self-similar Berkovich indenter, creep strain could be reduced at a deeper location. Such an indentation size effect on creep deformation was firstly reported for KDP crystals. The strain rate sensitivity of the steady-state creep flow was estimated, and the creep mechanism was qualitatively discussed.

High Temperature Deformation Mechanism Maps of NiAl

2004 ◽  
Vol 449-452 ◽  
pp. 57-60
Author(s):  
I.G. Lee ◽  
A.K. Ghosh
Keyword(s):  
High Temperature ◽  
Strain Rate ◽  
Deformation Mechanism ◽  
Calculation Method ◽  
Deformation Behavior ◽  
Tensile Tests ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Grain Sizes ◽  
Temperature Strain

In order to analyze high temperature deformation behavior of NiAl alloys, deformation maps were constructed for stoichiometric NiAl materials with grain sizes of 4 and 200 µm. Relevant constitute equations and calculation method will be described in this paper. These maps are particularly useful in identifying the location of testing domains, such as creep and tensile tests, in relation to the stress-temperature-strain rate domains experienced by NiAl.

Analysis of Hot Deformation Dynamics of TC18 Titanium Alloy

2013 ◽  
Vol 747-748 ◽  
pp. 878-884 ◽  
Author(s):  
Qing Rui Wang ◽  
Ai Xue Sha ◽  
Xing Wu Li ◽  
Li Jun Huang
Keyword(s):  
Titanium Alloy ◽  
Phase Transformation ◽  
Flow Stress ◽  
Strain Rate ◽  
Hot Deformation ◽  
Deformation Temperature ◽  
Relationship Model ◽  
Deformation Dynamics ◽  
Deformation Mechanics ◽  
Versus Strain

The effect of strain rate and deformation temperature on flow stress of TC18 titanium alloy was studied through heat simulating tests in 760~960 with temperature interval and the strain rate interval in 0.01~10s-1. Relationship model of flow stress versus strain was established and hot deformation mechanics of TC18 titanium alloy was analyzed. The results show that the flow stress reduces obviously as the deformation temperature increases or the strain rate decreases. Dynamic recovery occurs at high strain rate above phase transformation point, while dynamic recrystallization occurs at low strain rate as well as at the temperature below phase transformation point.

scholarly journals An Innovative Approach of Parameter Loading Path Design for Grain Refinement and Its Application in Ni80A Superalloy

Materials ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 6703
Author(s):  
Guo-Zheng Quan ◽  
Yan-Ze Yu ◽  
Xue Sheng ◽  
Kun Yang ◽  
Wei Xiong
Keyword(s):  
Strain Rate ◽  
Grain Refinement ◽  
Deformation Mechanism ◽  
Processing Parameters ◽  
Loading Path ◽  
Processing Parameter ◽  
Compression Process ◽  
Innovative Method ◽  
Path Design ◽  
Loading Path Design

In order to obtain the desired mechanical properties of products, an innovative method of loading parameter designs for acquiring the desired grain refinement is proposed, and it has been applied in the compression process of Ni80A superalloy. The deformation mechanism maps derived from processing maps based on the Dynamic Materials Model (DMM) theory were constructed, since the critical indicator values corresponding to dynamic recrystallization (DRX) and dynamic recovery (DRV) mechanisms were determined. The processing-parameter domains with DRX mechanisms were separated from the deformation mechanism map, while such domains were chaotic and difficult to apply in innovative parameter loading path design. The speed-loading path derived from strain rate-loading path in a compression process was pursued. The grain refinement domains are discretized into a finite series of sub-domains with clear processing parameters, and the optimal strain rate of each sub-domain is determined by step-by-step finite element simulation. A 3D response surface of the innovative optimal loading path of strain rate was fitted by interpolating methods. Finally, the isothermal compression experiments for Ni80A superalloy were conducted, and the microstructure observations indicated that the desired grain refinement was achieved. This innovative method of parameter loading path design contributes to the microstructure adjustment of the alloys with DRX mechanism.

Sign in / Sign up

Export Citation Format

Share Document