Design of high-efficiency turbomachinery blades for energy conversion devices with the three-dimensional prescribed surface curvature distribution blade design (CIRCLE) method

2012 ◽  
Vol 89 (1) ◽  
pp. 215-227 ◽  
Author(s):  
T. Korakianitis ◽  
I.A. Hamakhan ◽  
M.A. Rezaienia ◽  
A.P.S. Wheeler ◽  
E.J. Avital ◽  
...  
Keyword(s):  
Energy Conversion ◽  
High Efficiency ◽  
Circle Method ◽  
Three Dimensional ◽  
Surface Curvature ◽  
Blade Design ◽  
Turbomachinery Blades ◽  
Curvature Distribution ◽  
Energy Conversion Devices

Two- and Three-Dimensional Prescribed Surface Curvature Distribution Blade Design (CIRCLE) Method for the Design of High Efficiency Turbines, Compressors, and Isolated Airfoils

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
T. Korakianitis ◽  
M. A. Rezaienia ◽  
I. A. Hamakhan ◽  
A. P. S. Wheeler
Keyword(s):  
Turbine Blade ◽  
High Efficiency ◽  
Turbine Blades ◽  
Circle Method ◽  
Three Dimensional ◽  
Leading Edge ◽  
Surface Curvature ◽  
Blade Design ◽  
Compressor Blades ◽  
Curvature Distribution

The prescribed surface curvature distribution blade design (CIRCLE) method is presented for the design of two-dimensional (2D) and three-dimensional (3D) blades for axial compressors and turbines, and isolated blades or airfoils. The original axial turbine blade design method is improved, allowing it to use any leading-edge (LE) and trailing-edge (TE) shapes, such as circles and ellipses. The method to connect these LE and TE shapes to the remaining blade surfaces with curvature and slope of curvature continuity everywhere along the streamwise blade length, while concurrently overcoming the “wiggle” problems of higher-order polynomials is presented. This allows smooth surface pressure distributions, and easy integration of the CIRCLE method in heuristic blade-optimization methods. The method is further extended to 2D and 3D compressor blades and isolated airfoil geometries providing smooth variation of key blade parameters such as inlet and outlet flow angles, stagger angle, throat diameter, LE and TE radii, etc. from hub to tip. One sample 3D turbine blade geometry is presented. The efficacy of the method is examined by redesigning select blade geometries and numerically evaluating pressure-loss reduction at design and off-design conditions from the original blades: two typical 2D turbine blades; two typical 2D compressor blades; and one typical 2D isolated airfoil blade geometries are redesigned and evaluated with this method. Further extension of the method for centrifugal or mixed-flow impeller geometries is a coordinate transformation. It is concluded that the CIRCLE method is a robust tool for the design of high-efficiency turbomachinery blades.

Two- and Three-Dimensional Prescribed Surface Curvature Distribution Blade Design (CIRCLE) Method for the Design of High Efficiency Turbines, Compressors, and Isolated Airfoils

2011 ◽  
Author(s):  
T. Korakianitis ◽  
I. A. Hamakhan ◽  
M. A. Rezaienia ◽  
A. P. S. Wheeler
Keyword(s):  
Turbine Blade ◽  
High Efficiency ◽  
Turbine Blades ◽  
Circle Method ◽  
Three Dimensional ◽  
Leading Edge ◽  
Surface Curvature ◽  
Blade Design ◽  
Compressor Blades ◽  
Curvature Distribution

The prescribed surface curvature distribution blade design (CIRCLE) method is presented for the design of two-dimensional (2D) and three-dimensional (3D) blades for axial compressors and turbines, and isolated blades or airfoils. The original axial turbine blade design method is improved, allowing it to use any leading-edge (LE) and trailing-edge (TE) shapes, such as circles and ellipses. The method to connect these LE and TE shapes to the remaining blade surfaces with curvature and slope of curvature continuity everywhere along the streamwise blade length, while concurrently overcoming the “wiggle” problems of higher-order polynomials is presented. This allows smooth surface pressure distributions, and easy integration of the CIRCLE method in heuristic blade-optimization methods. The method is further extended to 2D and 3D compressor blades and isolated airfoil geometries providing smooth variation of key blade parameters such as inlet and outlet flow angles, stagger angle, throat diameter, LE and TE radii etc. from hub to tip. One sample 3D turbine blade geometry is presented. The efficacy of the method is examined by redesigning select blade geometries and numerically evaluating pressure-loss reduction at design and off-design conditions from the original blades: two typical 2D turbine blades; two typical 2D compressor blades; and one typical 2D isolated airfoil blade geometries are redesigned and evaluated with this method. Further extension of the method for centrifugal or mixed-flow impeller geometries is a coordinate transformation. It is concluded that the CIRCLE method is a robust tool for the design of high-efficiency turbomachinery blades.

Aerodynamic Improvements of Wind-Turbine Airfoil Geometries With the Prescribed Surface Curvature Distribution Blade Design (CIRCLE) Method

2011 ◽  
Author(s):  
T. Korakianitis ◽  
M. A. Rezaienia ◽  
I. A. Hamakhan ◽  
E. Avital ◽  
J. J. R. Williams
Keyword(s):  
Wind Turbine ◽  
Stagnation Point ◽  
Surface Pressure ◽  
Turbine Blades ◽  
Circle Method ◽  
Aerodynamic Performance ◽  
Surface Curvature ◽  
Blade Design ◽  
Drag Coefficients ◽  
Curvature Distribution

The prescribed surface curvature distribution blade design (CIRCLE) method can be used for the design of two-dimensional (2D) and three-dimensional (3D) turbomachinery blade rows with continuous curvature and slope of curvature from leading edge (LE) stagnation point to trailing edge (TE) stagnation point and back to the LE stagnation point. This feature results in smooth surface pressure distribution airfoils with inherently good aerodynamic performance. In this paper the CIRCLE blade design method is modified for the design of 2D isolated airfoils. As an illustration of the capabilities of the method, it is applied to the redesign of two representative airfoils used in wind turbine blades: the Eppler 387 airfoil; and the NREL S814 airfoil. Computational fluid dynamic analysis is used to investigate the design point and off-design performance of the original and modified airfoils, and compare with experiments on the original ones. The computed aerodynamic advantages of the modified airfoils are discussed. The surface pressure distributions, drag coefficients, and lift-to-drag coefficients of the original and redesigned airfoils are examined. It is concluded that the method can be used for the design of wind turbine blade geometries of superior aerodynamic performance.

Aerodynamic Improvements of Wind-Turbine Airfoil Geometries With the Prescribed Surface Curvature Distribution Blade Design (CIRCLE) Method

2012 ◽  
Vol 134 (8) ◽  
Author(s):  
T. Korakianitis ◽  
M. A. Rezaienia ◽  
I. A. Hamakhan ◽  
E. J. Avital ◽  
J. J. R. Williams
Keyword(s):  
Wind Turbine ◽  
Stagnation Point ◽  
Surface Pressure ◽  
Turbine Blades ◽  
Circle Method ◽  
Aerodynamic Performance ◽  
Surface Curvature ◽  
Blade Design ◽  
Drag Coefficients ◽  
Curvature Distribution

The prescribed surface curvature distribution blade design (CIRCLE) method can be used for the design of two-dimensional (2D) and three-dimensional (3D) turbomachinery blade rows with continuous curvature and slope of curvature from leading edge (LE) stagnation point to trailing edge (TE) stagnation point and back to the LE stagnation point. This feature results in smooth surface pressure distribution airfoils with inherently good aerodynamic performance. In this paper the CIRCLE blade design method is modified for the design of 2D isolated airfoils. As an illustration of the capabilities of the method, it is applied to the redesign of two representative airfoils used in wind turbine blades: the Eppler 387 airfoil and the NREL S814 airfoil. Computational fluid dynamic analysis is used to investigate the design point and off-design performance of the original and modified airfoils, and compare with experiments on the original ones. The computed aerodynamic advantages of the modified airfoils are discussed. The surface pressure distributions, drag coefficients, and lift-to-drag coefficients of the original and redesigned airfoils are examined. It is concluded that the method can be used for the design of wind turbine blade geometries of superior aerodynamic performance.

Non-Dimensional Parameters for Comparing Conventional and Counter-Rotating Turbomachines

2019 ◽  
Author(s):  
J. J. Waldren ◽  
C. J. Clark ◽  
S. D. Grimshaw ◽  
G. Pullan
Keyword(s):  
High Efficiency ◽  
Three Dimensional ◽  
Relative Performance ◽  
Design Parameters ◽  
Blade Design ◽  
Finite Radius ◽  
Counter Rotation ◽  
Dimensional Parameters ◽  
Conventional Machine ◽  
Stage Efficiency

Abstract Counter-rotating turbomachines have the potential to be high efficiency, high power density devices. Comparisons between conventional and counter-rotating turbomachines in the literature make multiple and often contradicting conclusions about their relative performance. By adopting appropriate non-dimensional parameters, based on relative blade speed, the design space of conventional machines can be extended to include those with counter-rotation. This allows engineers familiar with conventional turbomachinery to transfer their experience to counter-rotating machines. By matching appropriate non-dimensional parameters the loss mechanisms directly affected by counter-rotation can be determined. A series of computational studies are performed to investigate the relative performance of conventional and counter-rotating turbines with the same non-dimensional design parameters. Each study targets a specific loss source, highlighting which phenomena are directly due to counter-rotation and which are solely due to blade design. The studies range from two-dimensional blade sections to three-dimensional finite radius stages. It is shown that, at hub-to-tip ratios approaching unity, with matched non-dimensional design parameters, the stage efficiency and work output are identical for both types of machine. However, a counter-rotating turbine in the study is shown to have an efficiency advantage over a conventional machine of up to 0.35 percentage points for a hub-to-tip ratio of 0.65. This is due to differences in absolute velocity producing different spanwise blade designs.

Numerical Investigation of Surface Curvature Effects on Aerofoil Aerodynamic Performance

2015 ◽  
Vol 798 ◽  
pp. 589-595 ◽  
Author(s):  
Xiang Shen ◽  
Theodosios Korakianitis ◽  
Eldad Avital
Keyword(s):  
Separation Bubble ◽  
Circle Method ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Aerodynamic Performance ◽  
Surface Curvature ◽  
Operating Conditions ◽  
Curvature Effects ◽  
Curvature Continuity ◽  
Curvature Distribution

The prescribed surface curvature distribution blade design (CIRCLE) method optimises aerofoils and blades by controlling curvature continuity and slope of curvature distribution along their surfaces. The symmetrical NACA0012 exhibits a surface curvature discontinuity at the leading edge point, and the non-symmetrical E387 exhibits slope-of-curvature discontinuities in the surface. The CIRCLE method is applied to both aerofoils to remove both surface curvature and slope-of-curvature discontinuities. Computational fluid dynamics analyses are used to investigate the curvature effects on aerodynamic performance of the original and modified aerofoils. These results are compared with experimental data obtained from tests on the original aerofoil geometry. The computed aerodynamic advantages of the modified aerofoil are analysed in different operating conditions. The leading edge singularity of NACA0012 is removed and it is shown that the surface curvature discontinuity affects the aerodynamic performance near the stalling angle of attack. The discontinuous slope-of-curvature distribution of E387 influences the size of the laminar separation bubble at lower Reynolds numbers, and it affects the inherent profile of the aerofoil at higher Reynolds numbers. It is concluded that the surface curvature distribution of aerofoils has a significant effect on aerofoil aerodynamic performance, which can be improved by redesigning the surface curvature distribution of the original aerofoil geometry.

An Optimum Aero-Design Process of Turbine Blades

2002 ◽  
Author(s):  
C. Xu ◽  
R. S. Amano
Keyword(s):  
Design Process ◽  
High Efficiency ◽  
Pressure Ratio ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Optimization Procedure ◽  
Compressor Blade ◽  
Advanced Technology ◽  
Test Case ◽  
Blade Design

With the development of the advanced technology, the combustion temperature is raised for increased efficiencies. At the same time, the turbine and compressor pressure ratio and the mass flow rate rise; thus causing turbine and compressor blades turning and blade lengths increase. Moreover, the high efficiency requirements had made the turbine and compressor blade design difficult. A turbine airfoil has been custom designed for many years, but an optimization for the section design in a three-dimensional consideration is still a challenge. For a compressor blade design, standard section cannot meet the modern compressor requirements. Modern compressor design has not only needs a custom designed section according to flow situation, but also needs three-dimensional optimizations. Therefore, a good blade design process is critical to the turbines and compressors. A blade design of the turbomachines is one of the important steps for a good turbomachine design. A blade design process not only directly influences the overall machine efficiency but also dramatically impact the design time and cost. In this study, a blade design and optimization procedure was proposed for both turbine and compressor blade design. A compressor blade design was used as a test case. It was shown that the current design process had more advantages than conventional design methodology.

Graphene-supported 2D transition metal oxide heterostructures

2018 ◽  
Vol 6 (28) ◽  
pp. 13509-13537 ◽  
Author(s):  
Jalal Azadmanjiri ◽  
Vijay K. Srivastava ◽  
Parshant Kumar ◽  
James Wang ◽  
Aimin Yu
Keyword(s):  
Energy Storage ◽  
Transition Metal ◽  
Metal Oxide ◽  
Energy Conversion ◽  
High Efficiency ◽  
Transition Metal Oxide ◽  
Oxide Heterostructures ◽  
Energy Conversion Devices

New emerging graphene-supported 2D transition metal oxide heterostructures are attracting interest for high-efficiency energy storage and energy conversion devices.

A Turbomachinery Blade Design and Optimization Procedure

2002 ◽  
Author(s):  
C. Xu ◽  
R. S. Amano
Keyword(s):  
Design Process ◽  
High Efficiency ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Optimization Procedure ◽  
Compressor Blade ◽  
Advanced Technology ◽  
Test Case ◽  
Blade Design ◽  
Design And Optimization

With the development of the advanced technology, the combustion temperature is raised for increased efficiencies. At the same time, the turbine and compressor pressure ratio and the mass flow rate rise; thus causing turbine and compressor blades turning and blade lengths increase. Moreover, the high efficiency requirements had made the turbine and compressor blade design difficult. A turbine airfoil has been custom designed for many years, but an optimization for the section design in a three-dimensional consideration is still a challenge. For a compressor blade design, standard section cannot meet the modern compressor requirements. Modern compressor design has not only needs a custom designed section according to flow situation, but also needs three-dimensional optimizations. Therefore, a good blade design process is critical to the turbines and compressors. A blade design of the turbomachines is one of the important steps for a good turbomachine design. A blade design process not only directly influences the overall machine efficiency but also dramatically impact the design time and cost. In this study, a blade design and optimization procedure was proposed for both turbine and compressor blade design. A compressor blade design was used as a test case. It was shown that the current design process had more advantages than conventional design methodology.

Sign in / Sign up

Export Citation Format

Share Document