A complete rate-dependent constitutive model of thermo-elasto-diffusive coupling and its application in structural dynamic responses analysis of multi-layered laminated sandwich composites subjected to axisymmetric heat and chemical shock loadings

2022 ◽  
Author(s):  
Chenlin Li ◽  
Huili Guo ◽  
Tianhu He ◽  
Xiaogeng Tian
Keyword(s):  
Constitutive Model ◽  
Dynamic Responses ◽  
Sandwich Composites ◽  
Structural Dynamic ◽  
Diffusive Coupling ◽  
Rate Dependent

Wind tunnel tests and dynamic analysis of wind-induced response of a transmission tower on a hill

2021 ◽  
pp. 136943322110339
Author(s):  
Jian Guo ◽  
Changliang Xiao ◽  
Jiantao Li
Keyword(s):  
Wind Tunnel ◽  
Wind Field ◽  
Dynamic Responses ◽  
Interactive Effects ◽  
Induced Response ◽  
Transmission Tower ◽  
Structural Dynamic ◽  
Wind Tunnel Tests ◽  
Hill Slope ◽  
The Hill

A hill with a lattice transmission tower presents complex wind field characteristics. The commonly used computational fluid dynamics (CFD) simulations are difficult to analyze the wind resistance and dynamic responses of the transmission tower due to structural complexity. In this study, wind tunnel tests and numerical simulations are conducted to analyze the wind field of the hill and the dynamic responses of the transmission tower built on it. The hill models with different slopes are investigated by wind tunnel tests to measure the wind field characteristics, such as mean speed and turbulence intensity. The study shows that the existence of a transmission tower reduces the wind speed on the leeward slope significantly but has little effect on the windward slope. To study the dynamic behavior of the transmission tower, a hybrid analysis procedure is used by introducing the measured experimental wind information to the finite element tower model established using ANSYS. The effects of hill slope on the maximum displacement response of the tower are studied. The results show that the maximum value of the response is the largest when the hill slope is 25° compared to those when hill slope is 15° and 35°. The results extend the knowledge concerning wind tunnel tests on hills of different terrain and provide a comprehensive understanding of the interactive effects between the hill and existing transmission tower regarding to the wind field characteristics and structural dynamic responses.

scholarly journals A nonlinear strain-rate dependent constitutive model for uncured rubber materials under large deformation

2020 ◽  
Vol 37 ◽  
pp. 118-125
Author(s):  
Weihua Zhou ◽  
Changqing Fang ◽  
Huifeng Tan ◽  
Huiyu Sun
Keyword(s):  
Constitutive Model ◽  
Large Deformation ◽  
Mechanical Response ◽  
Uniaxial Tensile ◽  
Hysteresis Phenomenon ◽  
Mechanical Behaviors ◽  
Nonlinear Constitutive Model ◽  
Rate Dependent ◽  
Parallel Networks ◽  
Non Gaussian

Abstract Uncured rubber possesses remarkable hyperelastic and viscoelastic properties while it undergoes large deformation; therefore, it has wide application prospects and attracts great research interests from academia and industry. In this paper, a nonlinear constitutive model with two parallel networks is developed to describe the mechanical response of uncured rubber. The constitutive model is incorporated with the Eying model to describe the hysteresis phenomenon and viscous flow criterion, and the hyperelastic properties under large deformation are captured by a non-Gaussian chain molecular network model. Based on the model, the mechanical behaviors of hyperelasticity, viscoelasticity and hysteresis under different strain rates are investigated. Furthermore, the constitutive model is employed to estimate uniaxial tensile, cyclic loading–unloading and multistep tensile relaxation mechanical behaviors of uncured rubber, and the prediction results show good agreement with the test data. The nonlinear mechanical constitutive model provides an efficient method for predicting the mechanical response of uncured rubber materials.

Model Test and Numerical Analysis of an Offshore Bottom Fixed Pentapod Wind Turbine Under Seismic Loads

2016 ◽  
Author(s):  
Wenhua Wang ◽  
Zhen Gao ◽  
Xin Li ◽  
Torgeir Moan ◽  
Bin Wang
Keyword(s):  
Wind Turbine ◽  
Wind Wave ◽  
Seismic Analysis ◽  
Wind Farms ◽  
Dynamic Responses ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Test Model ◽  
Structural Dynamic ◽  
Load Conditions

In the last decade the wind energy industry has developed rapidly in China, especially offshore. For a water depth less than 20m, monopile and multi-pile substructures (tripod, pentapod) are applied widely in offshore wind farms. Some wind farms in China are located in high seismicity regions, thus, the earthquake load may become the dominant load for offshore wind turbines. This paper deals with the seismic behavior of an offshore wind turbine (OWT) consisting of the NREL 5MW baseline wind turbine, a pentapod substructure and a pile foundation of a real offshore wind turbine in China. A test model of the OWT is designed based on the hydro-elastic similarity. Test cases of different load combinations are performed with the environmental conditions generated by the Joint Earthquake, Wave and Current Simulation System and the Simple Wind Field Generation System at Dalian University of Technology, China, in order to investigate the structural dynamic responses under different load conditions. In the tests, a circular disk is used to model the rotor-nacelle system, and a force gauge is fixed at the center of the disk to measure the wind forces during the tests. A series of accelerometers are arranged along the model tower and the pentapod piles, and strain gauges glued on the substructure members are intended to measure the structural dynamic responses. A finite element model of the complete wind turbine is also established in order to compare the theoretical results with the test data. The hydro-elastic similarity is validated based on the comparison of the measured dynamic characteristics and the results of the prototype modal analysis. The numerical results agree well with the experimental data. Based on the comparisons of the results, the effect of the wind and sea loads on the structural responses subjected to seismic is demonstrated, especially the influence on the global response of the structure. It is seen that the effect of the combined seismic, wind, wave and current load conditions can not be simply superimposed. Hence the interaction effect in the seismic analysis should be considered when the wind, wave and current loads have a non-negligible effect.

The usage of hermite polynomial in the calculation of structural dynamic responses

1988 ◽  
Vol 9 (3) ◽  
pp. 241-251
Author(s):  
Zhang Yi-song ◽  
Xu Yin-ge ◽  
Gao Dc-ping
Keyword(s):  
Hermite Polynomial ◽  
Dynamic Responses ◽  
Structural Dynamic

Energy absorption behaviour of different grades of steel sheets using a strain rate dependent constitutive model

2017 ◽  
Vol 111 ◽  
pp. 9-18 ◽  
Author(s):  
Pundan K. Singh ◽  
Anindya Das ◽  
S. Sivaprasad ◽  
Pinaki Biswas ◽  
Rahul K. Verma ◽  
...  
Keyword(s):  
Constitutive Model ◽  
Strain Rate ◽  
Energy Absorption ◽  
Steel Sheets ◽  
Rate Dependent

scholarly journals Extension of Flow Behaviour and Damage Models for Cast Iron Alloys with Strain Rate Effect

2020 ◽  
Author(s):  
Chuang Liu ◽  
Dongzhi Sun ◽  
Xianfeng Zhang ◽  
Florence Andrieux ◽  
Tobias Gerster
Keyword(s):  
Cast Iron ◽  
Constitutive Model ◽  
Strain Rate ◽  
Mechanical Behavior ◽  
Damage Model ◽  
Iron Alloys ◽  
Strain Rate Range ◽  
Strain Rates ◽  
Damage Models ◽  
Rate Dependent

Abstract Cast iron alloys with low production cost and quite good mechanical properties are widely used in the automotive industry. To study the mechanical behavior of a typical ductile cast iron (GJS-450) with nodular graphite, uni-axial quasi-static and dynamic tensile tests at strain rates of 10− 4, 1, 10, 100, and 250 s− 1 were carried out. In order to investigate the effects of stress state, specimens with various geometries were used in the experiments. Stress–strain curves and fracture strains of the GJS-450 alloy in the strain-rate range of 10− 4 to 250 s− 1 were obtained. A strain rate-dependent plastic flow law based on the Voce model is proposed to describe the mechanical behavior in the corresponding strain-rate range. The deformation behavior at various strain rates is observed and analyzed through simulations with the proposed strain rate-dependent constitutive model. The available damage model from Bai and Wierzbicki is extended to take the strain rate into account and calibrated based on the analysis of local fracture strains. The validity of the proposed constitutive model including the damage model was verified by the corresponding experimental results. The results show that the strain rate has obviously nonlinear effects on the yield stress and fracture strain of GJS-450 alloys. The predictions with the proposed constitutive model and damage models at various strain rates agree well with the experimental results, which illustrates that the rate-dependent flow rule and damage models can be used to describe the mechanical behavior of cast iron alloys at elevated strain rates.

Three-dimensional constitutive model for shape-memory polymers considering temperature-rate dependent behavior

2021 ◽  
Vol 30 (3) ◽  
pp. 035030
Author(s):  
Jinsu Kim ◽  
Seung-Yeol Jeon ◽  
Seokbin Hong ◽  
Yongsan An ◽  
Haedong Park ◽  
...  
Keyword(s):  
Constitutive Model ◽  
Shape Memory ◽  
Three Dimensional ◽  
Shape Memory Polymers ◽  
Rate Dependent ◽  
Dependent Behavior ◽  
Temperature Rate
Sign in / Sign up

Export Citation Format

Share Document