Experimentally-based investigation of effects of wave interference on the wave resistance of asymmetric di-hulls

2017 ◽  
Vol 65 ◽  
pp. 142-153 ◽  
Author(s):  
Dongchi Yu ◽  
Pierre Lecointre ◽  
Ronald W. Yeung
2021 ◽  
Vol 932 ◽  
Author(s):  
Simen Å. Ellingsen

Vessels – in the widest sense – travelling on a water surface continuously do work the water surrounding it, causing energy to be radiated in the form of surface waves. The concomitant resistance force, the wave resistance, can account for as much as half the total drag on the vessel, so reducing it to a minimum has been a major part of ship design research for many decades. Whether the ‘vessel’ is an ocean-going ship or a swimming duckling, the physics governing the V-shaped pattern of radiated waves behind it is in essence the same, and just as fuel economy is important for commercial vessels, it is reasonable to assume that also swimming waterfowl seek to minimise their energy expenditure. Using theory and methods from classic marine hydrodynamics, Yuan et al. (J. Fluid Mech., vol. 928, 2021, R2) consider whether, by organising themselves optimally, ducklings in a row behind a mother duck can reduce, eliminate or even reverse their individual wave resistance. They describe two mechanisms which they term ‘wave riding’ and ‘wave passing.’ The former is intuitive: the ducklings closest to the mother can receive a forward push by riding its mother's stern waves. The latter is perhaps a more striking phenomenon: when the interduckling distance is precisely right, every duckling in the row can, in principle, swim without wave resistance due to destructive wave interference. The phenomenon appears to be the same as motivates the recent US military research project Sea Train, a row of unmanned vehicles travelling in row formation.


2020 ◽  
Vol 36 (03) ◽  
pp. 202-212
Author(s):  
W. Sulistyawati ◽  
_ Yanuar ◽  
A. S. Pamitran

This study attempted to investigate the hydrodynamic performance of various pentamaran configurations with a focus on the interference flow around the component hulls. A computer simulation was conducted based on Michell’s thin ship theory alongside a commercial CFD computation as a comparison. Experiments in the towing tank were performed to validate the numerical calculations, resulting in some hydrodynamic characteristics on the far-field wave pattern, wave interference, wave resistance, and total resistance. Analyses on both transversal and divergent waves were performed to assess the magnitude of wave resistance occurring due to the placement of the side hull to the main hull. Analyses on both waves were also conducted to assess the magnitude of wave resistance due to the placement of outriggers. Looking at the results, numerical calculations based on Michell’s theory were in parallel with experimental data, particularly at Fn greater than .4. Michell’s theory was observed as doing a little preferable agreement with the results of experiments than CFD. Besides, flow patterns obtained numerically from Michell’s and CFD analyses appeared as identical to photographs observed in a towing tank. This investigation identified that a configuration with aligning placement of the main to side hull on the formation of arrow tri-hull, near the Kelvin angle, would cancel the wave formed by the leading hull and can be used as a practical setting to reduce the total wave resistance.


1. If a ship is altered by inserting different lengths of parallel middle body between the same bow and stern, the main features of the variation in the wave resistance may be inferred from the principle of wave interference, and may be expressed in terms of a certain length, sometimes called the wave­-making length of the ship. The problem proposed for examination is the alteration in this length with varying length of parallel middle body at the same speed, and, further, its variation for a given ship at different speeds. Recent discussions have attracted renewed attention to this problem. It may be said that there are two approximations based on experimental results of various kinds obtained from ship models. On the one hand the wave-making length is supposed to be approximately independent of speed for a given ship, and to increase directly with the increase of parallel middle body; on the other hand, an empirical formula which agrees with experimental results over a certain range makes the length increase with velocity, the increase being one-quarter of the increase in the wave-length of regular transverse waves. The following contribution to the solution of this problem is mathematical, and necessarily deals with a simplified form of ship. It is true that one cannot compare absolute values of the wave resistance with those of actual ship models; but it has been shown in former studies of the dependence of wave resistance on ship form that one obtains a rather remarkable agreement, at least in the character of the results and in the positions at which changes occur. Leaving detailed discussion of the present extension till later, it may be stated that as regards the two approximate formulæ mentioned above the results are intermediate; after an initial decrease the wave-making length increases until velocity, but not so rapidly as in the quarter wave-length formula.


1971 ◽  
Vol 15 (01) ◽  
pp. 22-32
Author(s):  
Bohyun Yim

In an attempt to identify ways to reduce the peak wave resistance of surface effect ships, calculations of wave resistance are made for combinations of several singularity distributions with various parameters. Analyses are performed especially for the following components and parameters: various pressure planforms, the effect of sidewalls, the influence of sidewall camber, and the wave interference between the rectangular pressure planform with thin sidewalls and the front and rear skis. The result shows that, in general, the rectangular pressure planform is better than planforms of V-shaped bows and sterns. A gradual decrement of the sidewall displacement with the increasing Froude number is favorable, since not only the large buoyancy of sidewalls but also the low resistance helps the power reduction of SES for low-speed operations. Front and rear skis are helpful to reduce wave resistance for certain Froude numbers, although they may increase the drag for other Froude numbers. The camber of sidewall is not a good means for reducing the wave resistance of a rectangular pressure planform.


2014 ◽  
Vol 1 ◽  
pp. 324-327 ◽  
Author(s):  
Keisuke Nagata ◽  
Wataru Nakashima ◽  
Hisato Fujisaka ◽  
Takeshi Kamio ◽  
Kazuhisa Haeiwa

1955 ◽  
Vol 1955 (77) ◽  
pp. 1-28
Author(s):  
Masao Kinoshita ◽  
Atsushi Abe ◽  
Shojiro Okada
Keyword(s):  

1989 ◽  
Vol 25 (11) ◽  
pp. 728-730 ◽  
Author(s):  
K. Tsubaki ◽  
Y. Tokura ◽  
T. Fukui ◽  
H. Saito ◽  
N. Susa

2020 ◽  
Vol 10 (19) ◽  
pp. 6885
Author(s):  
Sahar Ujan ◽  
Neda Navidi ◽  
Rene Jr Landry

Radio Frequency Interference (RFI) detection and characterization play a critical role in ensuring the security of all wireless communication networks. Advances in Machine Learning (ML) have led to the deployment of many robust techniques dealing with various types of RFI. To sidestep an unavoidable complicated feature extraction step in ML, we propose an efficient Deep Learning (DL)-based methodology using transfer learning to determine both the type of received signals and their modulation type. To this end, the scalogram of the received signals is used as the input of the pretrained convolutional neural networks (CNN), followed by a fully-connected classifier. This study considers a digital video stream as the signal of interest (SoI), transmitted in a real-time satellite-to-ground communication using DVB-S2 standards. To create the RFI dataset, the SoI is combined with three well-known jammers namely, continuous-wave interference (CWI), multi- continuous-wave interference (MCWI), and chirp interference (CI). This study investigated four well-known pretrained CNN architectures, namely, AlexNet, VGG-16, GoogleNet, and ResNet-18, for the feature extraction to recognize the visual RFI patterns directly from pixel images with minimal preprocessing. Moreover, the robustness of the proposed classifiers is evaluated by the data generated at different signal to noise ratios (SNR).


Shock Waves ◽  
2021 ◽  
Author(s):  
C. Garbacz ◽  
W. T. Maier ◽  
J. B. Scoggins ◽  
T. D. Economon ◽  
T. Magin ◽  
...  

AbstractThe present study aims at providing insights into shock wave interference patterns in gas flows when a mixture different than air is considered. High-energy non-equilibrium flows of air and $$\hbox {CO}_2$$ CO 2 –$$\hbox {N}_2$$ N 2 over a double-wedge geometry are studied numerically. The impact of freestream temperature on the non-equilibrium shock interaction patterns is investigated by simulating two different sets of freestream conditions. To this purpose, the SU2 solver has been extended to account for the conservation of chemical species as well as multiple energies and coupled to the Mutation++ library (Multicomponent Thermodynamic And Transport properties for IONized gases in C++) that provides all the necessary thermochemical properties of the mixture and chemical species. An analysis of the shock interference patterns is presented with respect to the existing taxonomy of interactions. A comparison between calorically perfect ideal gas and non-equilibrium simulations confirms that non-equilibrium effects greatly influence the shock interaction patterns. When thermochemical relaxation is considered, a type VI interaction is obtained for the $$\hbox {CO}_2$$ CO 2 -dominated flow, for both freestream temperatures of 300 K and 1000 K; for air, a type V six-shock interaction and a type VI interaction are obtained, respectively. We conclude that the increase in freestream temperature has a large impact on the shock interaction pattern of the air flow, whereas for the $$\hbox {CO}_2$$ CO 2 –$$\hbox {N}_2$$ N 2 flow the pattern does not change.


2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Asghar Askarian

Abstract In this study, we are going to design all optical 1-bit comparator by combining wave interference and threshold switching methods. The final structure composed of two nonlinear ring resonators and seven waveguides. The functionality of the suggested logical structure is analyzed and simulated by using plane wave expansion (PWE) and finite difference time domain (FDTD) methods. According to results, the proposed all optical 1-bit comparator has faster response and smaller footprint than all previous works. The maximum ON-OFF contrast ratio, delay time and area of the suggested optical comparator are about 16.67 dB, 1.8 ps, and 513 µm2, respectively.


Sign in / Sign up

Export Citation Format

Share Document