Tip air injection to extend stall margin of multi-stage axial flow compressor with inlet radial distortion

2020 ◽  
Vol 96 ◽  
pp. 105554 ◽  
Author(s):  
Jichao Li ◽  
Juan Du ◽  
Shaojuan Geng ◽  
Fan Li ◽  
Hongwu Zhang
Keyword(s):  
Axial Flow ◽  
Air Injection ◽  
Stall Margin ◽  
Axial Flow Compressor ◽  
Radial Distortion ◽  
Multi Stage ◽  
Flow Compressor

Preference-Inspired Multi-Objective Throughflow-Design Optimization Approach of Axial Flow Compressor and its Application

2020 ◽  
Author(s):  
Youwei He ◽  
Jinju Sun ◽  
Peng Song ◽  
Xuesong Wang
Keyword(s):  
Design Optimization ◽  
Optimization Design ◽  
Velocity Ratio ◽  
Axial Flow ◽  
Optimization Approach ◽  
Stall Margin ◽  
Axial Flow Compressor ◽  
Multi Objective ◽  
Multi Stage ◽  
Flow Compressor

Abstract Throughflow design of multi-stage axial flow compressor still takes the upmost importance throughout the compressor whole design procedure as it generally fixes 80%∼90% of the final design. The incorporation of multi-objective evolutionary algorithms (MOEA) into throughflow design has been proven effective. In the existing works, the MOEA commonly uses thousands of objective evaluations to obtain a representative approximation of the complete Pareto front (PF), which usually consists of tens and hundreds of solutions. Once the representative PF is obtained, several typical solutions on the PF (especially the extreme ones and/or compromised ones) will be chosen and then examined by the decision-makers. But the remained considerable solutions on the PF are left behind, leading to a significant waste of computational resources. The preference-inspired MOEA has been suggested to resolve this problem as its focus on obtaining solutions in the region of interests only. In this work, a preference-inspired multi-objective axial flow compressor throughflow design optimization approach is developed through integrating the preference-inspired reference vector guided evolutionary algorithm and the open-source axial flow compressor axisymmetric throughflow design code of T-AXI. In terms of the objective definition for the multi-objective throughflow design, efficiency, stall margin, and blade counts are taken as the focuses. Specifically, the equivalent relative velocity ratio is adopted to form an operability parameter to assess designs with better or worse stall margin of the whole compressor. The developed method is used in the design of a 6-stage axial flow compressor at the throughflow level, which is a 3-objective problem with 58 variables. Preference-inspired and non-preference optimization are compared to verify the cost-saving benefit of incorporating the preferences into multi-objective optimization. Designs in the preferred target regions are obtained which demonstrates the practical ability of the proposed preference-inspired throughflow optimization design method for multi-stage axial flow compressors.

Influence of Rain Ingestion on the Endwall Treatment in an Axial Flow Compressor

2018 ◽  
Vol 140 (8) ◽  
Author(s):  
Jichao Li ◽  
Juan Du ◽  
Mingzhen Li ◽  
Feng Lin ◽  
Hongwu Zhang ◽  
...  
Keyword(s):  
Rotor Blade ◽  
Axial Flow ◽  
Pressure Rise ◽  
Water Film ◽  
Stall Margin ◽  
Axial Flow Compressor ◽  
Water Ingestion ◽  
Blade Row ◽  
Flow Compressor ◽  
The Stability

The effects of water ingestion on the performance of an axial flow compressor are experimentally studied with and without endwall treatment. The background to the work is derived from the assessment of airworthiness for an aero-engine. The stability-enhancing effects with endwall treatments under rain ingestion are not previously known. Moreover, all the endwall treatments are designed under dry air conditions in the compressor. Water ingestion at 3% and 5% relative to the design mass flow proposed in the airworthiness standard are applied to initially investigate the effects on the performance under smooth casing (SC). Results show that the water ingestions are mainly located near the casing wall after they move through the rotor blade row. The pressure rise coefficient increases, efficiency declines, and torque increases under the proposed water ingestion. The increase of the inlet water increases the thickness of the water film downstream the rotor blade row and aggravates the adverse effects on the performances. Subsequently, three endwall treatments, namely circumferential grooves, axial slots, and hybrid slots–grooves, are tested with and without water ingestion. Compared with no water ingestion, the circumferential grooves basically have no resistance to the water ingestion. The axial slots best prevent the drop of the pressure rise coefficient induced by water ingestion, and hybrid slots–grooves are the second-best place owing to the contribution of the front axial slots. Therefore, the hybrid slots–grooves can not only extend the stall margin with less efficiency penalty compared with axial slots, but also prevent rain ingestion from worsening the compressor performance.

Flow Studies on a Single Stage Transonic Axial Flow Compressor Retrofitted With Circumferential Grooves and Varied Rotor-Stator Axial Gap

2017 ◽  
Author(s):  
Anand P. Darji ◽  
Dilipkumar Bhanudasji Alone ◽  
Chetan S. Mistry
Keyword(s):  
Numerical Study ◽  
Computational Study ◽  
Axial Flow ◽  
Single Stage ◽  
Experimental Results ◽  
Stall Margin ◽  
Axial Flow Compressor ◽  
Transonic Compressor ◽  
Stall Margin Improvement ◽  
Flow Compressor

A transonic axial flow compressor undergoes severe vibrations due to instabilities like stall and surge when it operates at lower mass flow rate in the absence of any control devices. In present study, the attempt was made to understand the combine impact of circumferential casing grooves (CCG) of constant aspect ratio and different axial spacing between rotor and stator on the operating stability of single stage transonic axial compressor and that of rotor alone using numerical simulation. The optimum rotor-stator gap in the presence of grooved casing treatment was identified. The steady state numerical analysis was performed by using three-dimensional Reynolds Average Navier-Stokes equation adapting shear stress transport (SST) k-ω turbulence model. The study is reported in two sections. First section includes the detailed numerical study on baseline case having smooth casing wall (SCW). The computational results were validated with the experimental results available at Propulsion Division of CSIR-NAL, Bangalore. The computational study shows good agreement with experimental results. The second section comprises the effects of optimum designs of CCG and various axial spacing on the stall margin improvement of transonic compressor. Current computational study shows that the axial spacing between rotor and stator is an important parameter for improvement in stall margin not only for SCW but also for CCG. Therefore, the highest stall margin improvement of 9% has achieved for 75% axial spacing.

Numerical analysis of the effects of circumferential groove casing suction in a counter-rotating axial flow compressor

2020 ◽  
pp. 095765092095169
Author(s):  
Tian Liang ◽  
Bo Liu ◽  
Stephen Spence ◽  
Liying Jiao
Keyword(s):  
Axial Flow ◽  
Main Flow ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Stall Margin ◽  
Tip Leakage ◽  
Axial Flow Compressor ◽  
Circumferential Groove ◽  
Flow Compressor ◽  
The Impact

To extend the current understanding of the circumferential groove casing suction applied to a counter-rotating axial flow compressor, the impact of different axial locations of the circumferential suction groove on the characteristics of the tip leakage flow (TLF) and the corresponding physical mechanisms producing the stability enhancement have been studied based on validated numerical simulations. The results show that the optimal location for the suction groove is at around 20% axial chord, which demonstrated a high potential for reducing additional stall mass flow coefficient with about 8.4% increment in the stall margin. After the casing suction groove was applied, the interface between the incoming main flow and TLF was pushed significantly downstream in the second rotor. The blade loading in the region below the groove, the tip leakage flow angle and the reversed axial momentum flux injected into main flow passage through the tip gap were all reduced, which contributed to the stall margin improvement. Detailed analysis of the tip leakage flow structures showed that the TLF originating from different chord locations played different roles in the stall inception process. It was found to be more effective to improve stall margin and adiabatic efficiency by controlling the front part of the TLF, which was most sensitive.

Stability of Multi-Stage Axial Flow Compressors

1964 ◽  
Vol 15 (4) ◽  
pp. 328-356 ◽  
Author(s):  
W. T. Howell
Keyword(s):  
Axial Flow ◽  
Rotational Frequency ◽  
Oscillatory Instability ◽  
Operating Point ◽  
Axial Flow Compressor ◽  
Multi Stage ◽  
Wide Range ◽  
Surge Line ◽  
Flow Compressor ◽  
The Stability

SummaryThe following theoretical investigation is concerned with the stability of the flow through a system composed of a multi-stage axial flow compressor followed by a throttle.Such an investigation was carried out by Pearson and Bowmer in 1949. In 1962 Pearson’s work on the analysis of axial flow compressor characteristics, and the accumulation of empirical data regarding factors affecting the surge line, re-awakened interest in the possibility of predicting the surge line of a multi-stage axial flow compressor-throttle system.In this paper the equations governing the stability of flow at any operating point in such a system are obtained by applying Kirchhoff’s laws to the associated electric circuit at that operating point, and the analysis is applied to a wide range of flows of the calculated characteristics of a seven-stage axial flow compressor.A study of the simplest compressor-throttle system is given, in which the equations of motion of the system are derived mechanically and electrically, and the range of validity of the equations and their stability are discussed in order to bring out the relation between the mathematics and physics of the simple system before applying these methods to multi-stage axial flow compressors.For the relatively simple electrical representation used in this paper for an axial compressor of n stages, there are shown to be 2n possible values of p, the transient rotational frequency, and these are determined over a sufficiently wide range of flows on the seven-stage compressor studied.As a result, a region of the compressor characteristic map can be marked out in which all the values of the transient rotational frequency have their real parts less than zero, corresponding to stability of operation, a region where at least one of the values of p is real and positive corresponding to non-oscillatory instability of operation, and an intermediate region where some of the values of the rotational frequency p are complex with positive real part, corresponding to oscillatory instability of operation.It is suggested that the non-oscillatory instability found here is associated with the surge and the line of inception of non-oscillatory instability with the surge line.

Numerical Investigations of the Coupled Flow Through a Subsonic Compressor Rotor and Axial Skewed Slot

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
Xingen Lu ◽  
Wuli Chu ◽  
Junqiang Zhu ◽  
Yangfeng Zhang
Keyword(s):  
Axial Flow ◽  
Tip Clearance ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Casing Treatment ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Flow Through ◽  
Flow Compressor

In order to advance the understanding of the fundamental mechanisms of axial skewed slot casing treatment and their effects on the subsonic axial-flow compressor flow field, the coupled unsteady flow through a subsonic compressor rotor and the axial skewed slot was simulated with a state-of-the-art multiblock flow solver. The computational results were first compared with available measured data, that showed the numerical procedure calculates the overall effect of the axial skewed slot correctly. Then, the numerically obtained flow fields were interrogated to identify the physical mechanism responsible for improvement in stall margin of a modern subsonic axial-flow compressor rotor due to the discrete skewed slots. It was found that the axial skewed slot casing treatment can increase the stall margin of subsonic compressor by repositioning of the tip clearance flow trajectory further toward the trailing of the blade passage and retarding the movement of the incoming∕tip clearance flow interface toward the rotor leading edge plane.

Numerical Simulation of Steady Air Injection Flow Control Effects on a Transonic Axial Flow Compressor

2012 ◽  
Vol 224 ◽  
pp. 352-357
Author(s):  
Islem Benhegouga ◽  
Ce Yang
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Leading Edge ◽  
Air Injection ◽  
Axial Flow Compressor ◽  
Blade Tip ◽  
Flow Compressor

In this work, steady air injection upstream of the blade leading edge was used in a transonic axial flow compressor, NASA rotor 37. The injectors were placed at 27 % upstream of the axial chord length at blade tip, the injection mass flow rate is 3% of the chock mass flow rate, and 3 yaw angles were used, respectively -20°, -30°, and -40°. Negative yaw angles were measured relative to the compressor face in opposite direction of rotational speeds. To reveal the mechanism, steady numerical simulations were performed using FINE/TURBO software package. The results show that the stall mass flow can be decreased about 2.5 %, and an increase in the total pressure ratio up to 0.5%.

Sign in / Sign up

Export Citation Format

Share Document