scholarly journals Analysis of blockage and wrapping by leaves in the cutting mechanism of a sugarcane leaf shredder

2021 ◽  
Vol 211 ◽  
pp. 152-166
Author(s):  
Zhiguo Qiu ◽  
Yuxing Wang ◽  
Yanqin Tang ◽  
Wenhui Luo ◽  
Zilong Ye
Keyword(s):  
Cutting Mechanism

scholarly journals Studies on Orthogonal Cutting Mechanism with Pb-Sn Alloy

1969 ◽  
Vol 35 (275) ◽  
pp. 1557-1564
Author(s):  
Yoshiya FUJII ◽  
Kiyoshi TAGAMI ◽  
Masaru MATSUNO ◽  
Katsuhide MIURA
Keyword(s):  
Orthogonal Cutting ◽  
Cutting Mechanism

Near-infrared luminescence and quantum cutting mechanism in CaWO4:Nd3+, Yb3+

2013 ◽  
Vol 111 (3) ◽  
pp. 367-371 ◽  
Author(s):  
Jiayue Sun ◽  
Yining Sun ◽  
Chun Cao ◽  
Zhiguo Xia ◽  
Haiyan Du
Keyword(s):  
Near Infrared ◽  
Cutting Mechanism ◽  
Infrared Luminescence ◽  
Quantum Cutting

scholarly journals Comparison of cutting mechanism when machining micro and nano-particles reinforced SiC/Al metal matrix composites

2018 ◽  
Vol 203 ◽  
pp. 636-647 ◽  
Author(s):  
Xiangyu Teng ◽  
Wanqun Chen ◽  
Dehong Huo ◽  
Islam Shyha ◽  
Chao Lin
Keyword(s):  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Nano Particles ◽  
Matrix Composites ◽  
Cutting Mechanism

Cutting Mechanism Investigation in Vibration-Assisted Machining

2018 ◽  
Vol 1 (4) ◽  
pp. 268-276 ◽  
Author(s):  
Wanqun Chen ◽  
Lu Zheng ◽  
Xiangyu Teng ◽  
Kai Yang ◽  
Dehong Huo
Keyword(s):  
Cutting Mechanism

Dynamic analysis of a cutting mechanism

2000 ◽  
Vol 35 (10) ◽  
pp. 1391-1411 ◽  
Author(s):  
L. Cveticanin ◽  
R. Maretic
Keyword(s):  
Dynamic Analysis ◽  
Cutting Mechanism

Research on arc cutting mechanism and procedure of flux-cored cutting wire in water

2018 ◽  
Vol 98 (9-12) ◽  
pp. 2895-2904 ◽  
Author(s):  
Wenhang Li ◽  
Jingyu Zhao ◽  
Jiayou Wang ◽  
Jianxin Wang ◽  
Haifeng Jia ◽  
...  
Keyword(s):  
Cutting Mechanism

scholarly journals Cutting Mechanism of Sulfrized Free-Machining Steel

2009 ◽  
Vol 407-408 ◽  
pp. 416-419 ◽  
Author(s):  
Junsuke Fujiwara ◽  
Tsubasa Kawazoe ◽  
Naoki Matsui
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Deformation Behavior ◽  
Environmental Problem ◽  
Orthogonal Cutting ◽  
Machining Performance ◽  
Cutting Mechanism ◽  
Deformation Behaviors ◽  
Production Industry ◽  
Scanning Electron

Leaded free-machining steel is used in production industry. However the use of the leaded free-machining steel is limited from an environmental problem. So sulfurized free-machining steel, not include lead, has been researched widely. In order to improve the machining performance of the sulfurized free-machining steel, it is necessary to find out the behavior of inclusion. The experiment was carried out to find out the mechanism of the surfurized inclusion on the machinability, using some kinds of materials which were changed the size of the inclusion. In orthogonal cutting, the deformation behaviors of the sulfurized inclusion in the work materials were observed in the vicinity of tool face. Cutting forces were also measured and finished surfaces were observed. Besides, low speed orthogonal cutting in Scanning Electron Microscope (SEM) which was mounted a small cutting device was carried out in order to observe the deformation behavior more microscopically. As a result, it is clear that some inclusions creates voids around them and some broke to several pieces depending on their conditions. Moreover, in order to investigate the formation and growth of BUE, a quick stop experiment was done during turning. As a result, it is clear that the larger inclusions can reduce the formation of BUE.

scholarly journals Studies on the Draft-Cutting Mechanism

1954 ◽  
Vol 10 (6) ◽  
pp. 261-265
Author(s):  
Shoichi Ishikawa ◽  
Masaaki Tabata
Keyword(s):  
Cutting Mechanism

scholarly journals 622 Cutting Mechanism of Sulfurized Free-Machining Steel

2009 ◽  
Vol 2009.84 (0) ◽  
pp. _6-26_
Author(s):  
Junsuke FUJIWARA ◽  
Tsubasa KAWAZOE
Keyword(s):  
Cutting Mechanism
Sign in / Sign up

Export Citation Format

Share Document