Over 1 A/mm drain current density and 3.6 W/mm output power density in 2DHG diamond MOSFETs with highly doped regrown source/drain

Carbon ◽  
2021 ◽  
Author(s):  
Ken Kudara ◽  
Masakazu Arai ◽  
Yukiko Suzuki ◽  
Aoi Morishita ◽  
Jun Tsunoda ◽  
...  
Keyword(s):  
Power Density ◽  
Output Power ◽  
Current Density ◽  
Drain Current

4H-SiC Planar MESFETs on High-Purity Semi-Insulating Substrates

2007 ◽  
Vol 556-557 ◽  
pp. 763-766 ◽  
Author(s):  
Jeong Hyuk Yim ◽  
Ho Keun Song ◽  
Jeong Hyun Moon ◽  
Han Seok Seo ◽  
Jong Ho Lee ◽  
...  
Keyword(s):  
Power Density ◽  
Output Power ◽  
High Purity ◽  
Maximum Output Power ◽  
Drain Current ◽  
Maximum Output ◽  
Power Gain ◽  
Si Substrates ◽  
Class A ◽  
Current Instability

Planar MESFETs were fabricated on high-purity semi-insulating (HPSI) 4H-SiC substrates. The saturation drain current of the fabricated MESFETs with a gate length of 0.5 μm and a gate width of 100 μm was 430 mA/mm, and the transconductance was 25 mS/mm. The maximum oscillation frequency and cut-off frequency were 26.4 GHz and 7.2 GHz, respectively. The power gain was 8.4 dB and the maximum output power density was 2.8 W/mm for operation of class A at CW 2 GHz. MESFETs on HPSI substrates showed no current instability and much higher output power density in comparison to MESFETs on vanadium-doped SI substrates.

scholarly journals Power Density Improvement of Piezoelectric Energy Harvesters via a Novel Hybridization Scheme with Electromagnetic Transduction

Micromachines ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 803
Author(s):  
Zhongjie Li ◽  
Chuanfu Xin ◽  
Yan Peng ◽  
Min Wang ◽  
Jun Luo ◽  
...  
Keyword(s):  
Power Density ◽  
Output Power ◽  
Energy Harvester ◽  
Hybrid Energy ◽  
Energy Harvesters ◽  
Piezoelectric Patch ◽  
Piezoelectric Energy ◽  
Electromagnetic Transduction ◽  
Self Powered ◽  
Power Densities

A novel hybridization scheme is proposed with electromagnetic transduction to improve the power density of piezoelectric energy harvester (PEH) in this paper. Based on the basic cantilever piezoelectric energy harvester (BC-PEH) composed of a mass block, a piezoelectric patch, and a cantilever beam, we replaced the mass block by a magnet array and added a coil array to form the hybrid energy harvester. To enhance the output power of the electromagnetic energy harvester (EMEH), we utilized an alternating magnet array. Then, to compare the power density of the hybrid harvester and BC-PEH, the experiments of output power were conducted. According to the experimental results, the power densities of the hybrid harvester and BC-PEH are, respectively, 3.53 mW/cm3 and 5.14 μW/cm3 under the conditions of 18.6 Hz and 0.3 g. Therefore, the power density of the hybrid harvester is 686 times as high as that of the BC-PEH, which verified the power density improvement of PEH via a hybridization scheme with EMEH. Additionally, the hybrid harvester exhibits better performance for charging capacitors, such as charging a 2.2 mF capacitor to 8 V within 17 s. It is of great significance to further develop self-powered devices.

213 W 500 Mhz 4H-SiC Static Induction Transistor

2011 ◽  
Vol 130-134 ◽  
pp. 3392-3395 ◽  
Author(s):  
Gang Chen ◽  
Peng Wu ◽  
Song Bai ◽  
Zhe Yang Li ◽  
Yun Li ◽  
...  
Keyword(s):  
Current Density ◽  
Drain Current ◽  
Total Power ◽  
Class Ab ◽  
Blocking Voltage ◽  
Finger Width ◽  
Static Induction Transistor ◽  
Recessed Gate ◽  
Total Power Output ◽  
A Current

. Silicon carbide (SiC) SITs were fabricated using home-grown epi structures. The gate is a recessed gate - bottom contact (RG - B). We designed that the mesa space 2.7μm and the gate channel is 1.2μm. One cell has 400 source fingers and each source finger width is 100μm. 1mm SiC SIT yielded a current density of 123mA/mm of drain current at a drain voltage of 20V. A maximum current density of 150 mA/mm was achieved with Vd=40V. The device blocking voltage with a gate bias of-16 V was 200 V. Packaged 24-cm devices were evaluated using amplifier circuits designed for class AB operations. A total power output in excess of 213 W was obtained with a power density of 8.5 W/cm and gain of 8.5 dB at 500 MHz under pulse operation.

Fabrication and Characterization of Anode-Supported SDC Film Electrolyte and its Single Cell

2010 ◽  
Vol 177 ◽  
pp. 407-410
Author(s):  
Xi Bao Li ◽  
Jian Wang ◽  
Xiao Hua Yu ◽  
Hong Xing Gu ◽  
Gang Qin Shao
Keyword(s):  
Single Cell ◽  
Power Density ◽  
Flow Rate ◽  
Current Density ◽  
Tape Casting ◽  
Threshold Value ◽  
Interface Layer ◽  
Open Circuit ◽  
Discharge Performance ◽  
Film Electrolyte

NiO-YSZ (NiO-yttria stabilized zirconia, 3:2, wt.%) and samaria doped ceria (SDC) tapes were prepared by aqueous tape casting. NiO-YSZ anode-supported SDC film electrolyte half-cell was fabricated by laminating and co-sintering at 1400°C for 2 h. The single cell was prepared after LSCF-SDC (lanthanum strontium cobalt ferrite-SDC, 1:1, wt.%) cathode was coated on the electrolyte surface and sintered at 1300 °C for 2 h. The discharge performance of the single cell was tested from 500 °C to 800 °C at different H2 flow rate. Results showed that the relationship between current (I) of and H2 flow rate (ν) was I = 8 × 106 ν. Before reaching the threshold value of H2 flow rate, the current density of single cell increased with the increasing of H2 flow rate. However, the current density did not change with increasing of H2 flow rate over the threshold value. The open circuit voltage (OCV) of single cell at 500°C, 600°C, 700°C, 800°C was 0.978, 0.921, 0.861, 0.803 V, respectively. The maximum power density reached 93.03 mW/cm2 at 800°C. The resistance of interface layer between Ni-YSZ anode and SDC electrolyte was the key impact on the power density.

A 4.69-W/mm output power density InAlN/GaN HEMT grown on sapphire substrate

2011 ◽  
Vol 32 (12) ◽  
pp. 124003 ◽  
Author(s):  
Bo Liu ◽  
Zhihong Feng ◽  
Sen Zhang ◽  
Shaobo Dun ◽  
Jiayun Yin ◽  
...  
Keyword(s):  
Power Density ◽  
Output Power ◽  
Sapphire Substrate ◽  
Gan Hemt

Thermoelectric module design to improve lifetime and output power density

2021 ◽  
Vol 18 ◽  
pp. 100391
Author(s):  
W. Sun ◽  
R. Sui ◽  
G. Yuan ◽  
H. Zheng ◽  
Z. Zeng ◽  
...  
Keyword(s):  
Power Density ◽  
Output Power ◽  
Thermoelectric Module ◽  
Module Design

The Effect of Inlet Parameters on Fluid Flow and Cell Performance at Cathode of a Proton Exchange Membrane Fuel Cell

2010 ◽  
Vol 7 (4) ◽  
Author(s):  
Utku Gulan ◽  
Hasmet Turkoglu ◽  
Irfan Ar
Keyword(s):  
Reynolds Number ◽  
Fuel Cell ◽  
Power Density ◽  
Current Density ◽  
Proton Exchange Membrane ◽  
Catalyst Layer ◽  
Pem Fuel Cell ◽  
Proton Exchange ◽  
Exchange Membrane ◽  
Oxygen Mole Fraction

In this study, the fluid flow and cell performance in cathode side of a proton exchange membrane (PEM) fuel cell were numerically analyzed. The problem domain consists of cathode gas channel, cathode gas diffusion layer, and cathode catalyst layer. The equations governing the motion of air, concentration of oxygen, and electrochemical reactions were numerically solved. A computer program was developed based on control volume method and SIMPLE algorithm. The mathematical model and program developed were tested by comparing the results of numerical simulations with the results from literature. Simulations were performed for different values of inlet Reynolds number and inlet oxygen mole fraction at different operation temperatures. Using the results of these simulations, the effects of these parameters on the flow, oxygen concentration distribution, current density and power density were analyzed. The simulations showed that the oxygen concentration in the catalyst layer increases with increasing Reynolds number and hence the current density and power density of the PEM fuel cell also increases. Analysis of the data obtained from simulations also shows that current density and power density of the PEM fuel cell increases with increasing operation temperature. It is also observed that increasing the inlet oxygen mole fraction increases the current density and power density.

Sign in / Sign up

Export Citation Format

Share Document