Pretreatment of wastewater from acrylonitrile–butadiene–styrene (ABS) resin manufacturing by microelectrolysis

2012 ◽  
Vol 179 ◽  
pp. 1-7 ◽  
Author(s):  
Bo Lai ◽  
Yuexi Zhou ◽  
Hongke Qin ◽  
Changyong Wu ◽  
Cuicui Pang ◽  
...  
Keyword(s):  
Acrylonitrile Butadiene Styrene ◽  
Abs Resin ◽  
Butadiene Styrene

Structure and properties of heat-resistant ABS resins innovated via MSAMI random copolymer

2021 ◽  
pp. 089270572110441
Author(s):  
BY Hou ◽  
L Ren ◽  
YN Sun ◽  
MY Zhang ◽  
HX Zhang
Keyword(s):  
Mechanical Properties ◽  
Heat Resistance ◽  
Acrylonitrile Butadiene Styrene ◽  
Random Copolymer ◽  
Softening Temperature ◽  
Fracture Morphology ◽  
Structure And Properties ◽  
Heat Resistant ◽  
Abs Resin ◽  
Butadiene Styrene

This work proposed an efficient method to synthesize acrylonitrile-butadiene-styrene (ABS) copolymer and α-Methylstyrene (α-MSt)/N-phenylmaleimide (NPMI)/Acrylonitrile (AN) (MSAMI) random copolymer via emulsion polymerization, aiming to combine the excellent heat resistance of MSAMI and numerous advantages of ABS resin including mechanical properties, processing and recyclability. The effects of the MSAMI content and α-MSt/AN ratio on the thermal performance, mechanical properties and the morphology of heat-resistant ABS were investigated by FITR, dynamic mechanical analyses (DMA), Vicat Softening Temperature (VST), Thermogravimetric Analysis (TGA) and Scanning Electron Microscope (SEM). As a result, the heat-resistant of ABS resin was obviously enhanced by MSAMI, and its glass transition temperature (Tg) could be extended with the increase of NPMI content. The Tg could reach 173°C when NPMI content was 20% at the same trend as the VST. Synthetically, the contradiction between the heat resistance and mechanical properties of ABS resin reached a good balance when the NPMI content was 15% and α-MSt/AN ratio was 69/31. In SEM, the fracture morphology of the heat-resistant ABS resin was gradually tended to be smooth with the increase of the NPMI content. Therefore, the MSAMI random copolymer was successful prepared, which provided insight for the synthesis of heat-resistant modifiers and promoted the potential application of heat-resistant modifiers in automobiles and aircraft.

Preparation and Characterization of Wood-Plastic Nanocomposites Based on Acrylonitrile-Butadiene-Styrene

2021 ◽  
Vol 21 (9) ◽  
pp. 4840-4845
Author(s):  
Guixin Zhang ◽  
Yanyan Zhang ◽  
Jun Yang ◽  
Shijuan Li ◽  
Weihong Guo
Keyword(s):  
Mechanical Properties ◽  
Interfacial Adhesion ◽  
Flexural Modulus ◽  
Acrylonitrile Butadiene Styrene ◽  
High Water ◽  
Abs Resin ◽  
Reactive Compatibilizer ◽  
Butadiene Styrene

The new wood-plastic nanocomposites (WPC) based on acrylonitrile-butadiene-styrene (ABS) resin was successfully blended with ABS and poplar flour (PF) through a HAAKE rheomix. The mechanical properties of nanocomposites, except for flexural modulus, were reduced after increasing the PF content. SEM photos show the reduction resulting from weak interfacial adhesion between the PF phase and ABS phase. Higher PF content leads to a low thermal stability and a high water absorption ratio. Different coupling agents (CA) were employed to improve the compatibility between PF and ABS. The results suggest that ABS-g-MAH is more effective than POE-g-MAH, EVA and SEBS. Maleic anhydride (MA) was blended in situ with PF and ABS as the reactive compatibilizer and mechanical properties of nanocomposites were improved except impact strength.

scholarly journals Study on Exothermic Oxidation of Acrylonitrile-butadiene-styrene (ABS) Resin Powder with Application to ABS Processing Safety

Polymers ◽  
2010 ◽  
Vol 2 (3) ◽  
pp. 174-187 ◽  
Author(s):  
Yih-Shing Duh ◽  
Ta-Cheng Ho ◽  
Jenq-Renn Chen ◽  
Chen-Shan Kao
Keyword(s):  
Acrylonitrile Butadiene Styrene ◽  
Abs Resin ◽  
Exothermic Oxidation ◽  
Butadiene Styrene

scholarly journals Synthesis of Environmentally Friendly Acrylonitrile Butadiene Styrene Resin with Low VOC

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1663
Author(s):  
Licheng Fan ◽  
Lijuan Wei ◽  
Yongfei Zhu ◽  
Yibo Wang ◽  
Jianmin Fei ◽  
...  
Keyword(s):  
Residence Time ◽  
Chain Transfer ◽  
Acrylonitrile Butadiene Styrene ◽  
Extraction Process ◽  
Supercritical Extraction ◽  
Vacuum Degree ◽  
Abs Resin ◽  
Methyl Styrene ◽  
Dodecyl Mercaptan ◽  
Butadiene Styrene

Most acrylonitrile butadiene styrene (ABS) resin is plagued by an unpleasant odor attributed to the high residual volatile organic compound (VOC) content. This paper primarily aimed to solve the odor issue of ABS resin by effectively reducing the VOC content. To that end, a synthesis of ABS resins was optimized through a supercritical extraction process while evaluating multiple novel chain transfer agents (linear dimer of α-methyl-styrene, methyl 3-mercaptopropionate, and dodecyl mercaptan). ABS resin obtained through a α-methyl-styrene chain transfer agent demonstrated the lowest odor. Moreover, it had the least amount of VOC content which was three times lower than when dodecyl mercaptan was employed. To improve the supercritical extraction process, an orthogonal test was designed to optimize four main process parameters: extrusion temperature, residence time, vacuum degree and extractant dosage. The most optimal conditions were found to be 250 °C extrusion temperature, one minute residence time, vacuum degree of minus 99 KPa, and 1.5% CO2 extractant dosage.

scholarly journals Effects of Reprocessing on Acrylonitrile–Butadiene–Styrene and Additives

2021 ◽  
Author(s):  
Xiaojuan Bai ◽  
Pin Liang ◽  
Mei Zhang ◽  
Shiqiong Gong ◽  
Lihua Zhao
Keyword(s):  
Structural Changes ◽  
Acrylonitrile Butadiene Styrene ◽  
Gel Permeation Chromatography ◽  
Processing Parameters ◽  
Gas Chromatography Mass Spectrometry ◽  
Pyrolysis Gas ◽  
Large Size ◽  
Abs Resin ◽  
Engineering Polymers ◽  
Butadiene Styrene

Abstract Acrylonitrile-butadiene-styrene (ABS) is one of the most extensively used engineering polymers and analysing the chemical structure changes during processing and recycling is extremely important. Hence, in this study, an ABS resin was processed using a torque rheometer at different temperatures and for different numbers of cycles. Pyrolysis gas chromatography mass spectrometry (Py-GC/MS) was used to study the effects of the processing parameters on additives. Fourier transform infrared spectroscopy (FTIR), hydrogen nuclear magnetic resonance (1H NMR) spectroscopy, and gel permeation chromatography (GPC) were used to analyse the structural changes in the resin. GPC results showed that after processing at 290 °C using the torque rheometer, large size soluble polymeric components increased. The increase in the large size soluble polymeric components after processing at 290 °C was probably related to the crosslinking reactions in the grafted polybutadiene (PB). Furthermore, chemical analysis of the ABS resin samples after multiple extrusion cycles in a twin-screw extruder indicated that reprocessing considerably affected the ABS resin.

Flame Retardant ABS with a Novel Polyphosphate Derived from Biomass

2011 ◽  
Vol 284-286 ◽  
pp. 187-192 ◽  
Author(s):  
Yan Zhang ◽  
Xiao Ling Chen ◽  
Zheng Ping Fang
Keyword(s):  
Thermal Stability ◽  
Thermogravimetric Analysis ◽  
Flame Retardant ◽  
Cone Calorimeter ◽  
Fire Retardant ◽  
Acrylonitrile Butadiene Styrene ◽  
Cone Calorimeter Test ◽  
Abs Resin ◽  
Intumescent System ◽  
Butadiene Styrene

Acrylonitrile-butadiene-styrene (ABS) was treated with various formulations containing an intumescent fire retardant, which consists of ammonium polyphosphate (APP) and a novel char-forming agent, poly(diphenolic phenyl phosphate)(poly(DPA-PDCP)). The behaviour of this intumescent system was investigated by thermogravimetric analysis (TGA), LOI test and cone calorimeter test, respectively. The results showed that the addition of poly(DPA-PDCP) enhanced the thermal stability and flame retardancy of ABS/APP. The weight of residues improved with the addition of poly(DPA-PDCP) . SEM investigations of residual char burning after cone calorimeter test revealed that poly(DPA-PDCP) plays an stimulative role in the process of carbonization. The intumescent chars formed from ABS/APP/ poly(DPA-PDCP) composites were intact and strong. It is confirmed that the poly(DPA-PDCP) is an efficient char-forming agent for flame retardant ABS resin.

Sign in / Sign up

Export Citation Format

Share Document