Mechanical, thermal and morphological characterization of cellulose fiber-reinforced phenolic foams

The objective of this research is to study the feasibility of using fiber obtained from tobacco stalk as reinforcement fiber in the production of fiber cement through hydrothermal methods. The fiber cement samples are made of the mixtures of 50% of ASTM Type I ordinary Portland cement, 35% of milled sand, 10% of calcium carbonate powder and 5% of cellulose fiber (eucalyptus pulp and tobacco stalk pulp). This study include the morphological characterization of the fibers and the study of effects that the use of fiber has on the fiber cement suspensions and on the mechanical and physical properties of the final product. The flexural strength of fiber cement samples using tobacco stalk pulp after curing in an autoclave at 180 °C for 4 hours is 14.21 MPa which is slightly lower than that of the samples using eucalyptus pulp at 17.10 MPa. However, the results obtained in the tests confirmed the high potential of the tobacco stalk as a source of fiber for the fabrication of a fiber cement capable of meeting the requirements of demanding applications.

Download Full-text

Morphological Characterization of Mycobacteriophage R1

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100051281 ◽

1974 ◽

Vol 32 ◽

pp. 254-255

Author(s):

B. L. Soloff ◽

T. A. Rado

Keyword(s):

Carbon Source ◽

Stationary Phase ◽

Growth Phase ◽

Minimal Medium ◽

Morphological Characterization ◽

Logarithmic Growth Phase ◽

Complete Lysis ◽

Lysogenic Culture ◽

Logarithmic Growth

Mycobacteriophage R1 was originally isolated from a lysogenic culture of M. butyricum. The virus was propagated on a leucine-requiring derivative of M. smegmatis, 607 leu−, isolated by nitrosoguanidine mutagenesis of typestrain ATCC 607. Growth was accomplished in a minimal medium containing glycerol and glucose as carbon source and enriched by the addition of 80 μg/ ml L-leucine. Bacteria in early logarithmic growth phase were infected with virus at a multiplicity of 5, and incubated with aeration for 8 hours. The partially lysed suspension was diluted 1:10 in growth medium and incubated for a further 8 hours. This permitted stationary phase cells to re-enter logarithmic growth and resulted in complete lysis of the culture.

Download Full-text

TEM characterization of reaction zone in a SiC fiber-reinforced titanium alloy

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100105758 ◽

1988 ◽

Vol 46 ◽

pp. 738-739

Author(s):

G. Das ◽

R. E. Omlor

Keyword(s):

Titanium Alloys ◽

Reaction Zone ◽

Carbon Layer ◽

Fiber Reinforced ◽

Reaction Products ◽

Sic Fibers ◽

Sic Fiber ◽

The Matrix ◽

Immense Potential

Fiber reinforced titanium alloys hold immense potential for applications in the aerospace industry. However, chemical reaction between the fibers and the titanium alloys at fabrication temperatures leads to the formation of brittle reaction products which limits their development. In the present study, coated SiC fibers have been used to evaluate the effects of surface coating on the reaction zone in the SiC/IMI829 system.IMI829 (Ti-5.5A1-3.5Sn-3.0Zr-0.3Mo-1Nb-0.3Si), a near alpha alloy, in the form of PREP powder (-35 mesh), was used a茸 the matrix. CVD grown AVCO SCS-6 SiC fibers were used as discontinuous reinforcements. These fibers of 142μm diameter contained an overlayer with high Si/C ratio on top of an amorphous carbon layer, the thickness of the coating being ∽ 1μm. SCS-6 fibers, broken into ∽ 2mm lengths, were mixed with IMI829 powder (representing < 0.1vol%) and the mixture was consolidated by HIP'ing at 871°C/0. 28GPa/4h.

Download Full-text

Characterization of interfaces in CVD-coated nicalon fiber-reinforced SiC

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100154755 ◽

1989 ◽

Vol 47 ◽

pp. 556-557

Author(s):

K.L. More ◽

R.A. Lowden

Keyword(s):

Mechanical Properties ◽

Fracture Toughness ◽

Chemical Vapor ◽

Chemical Vapor Infiltration ◽

Frictional Stress ◽

Fiber Reinforced ◽

Pull Out ◽

Carbon Coated ◽

Fiber Matrix

The mechanical properties of fiber-reinforced composites are directly related to the nature of the fiber-matrix bond. Fracture toughness is improved when debonding, crack deflection, and fiber pull-out occur which in turn depend on a weak interfacial bond. The interfacial characteristics of fiber-reinforced ceramics can be altered by applying thin coatings to the fibers prior to composite fabrication. In a previous study, Lowden and co-workers coated Nicalon fibers (Nippon Carbon Company) with silicon and carbon prior to chemical vapor infiltration with SiC and determined the influence of interfacial frictional stress on fracture phenomena. They found that the silicon-coated Nicalon fiber-reinforced SiC had low flexure strengths and brittle fracture whereas the composites containing carbon coated fibers exhibited improved strength and fracture toughness. In this study, coatings of boron or BN were applied to Nicalon fibers via chemical vapor deposition (CVD) and the fibers were subsequently incorporated in a SiC matrix. The fiber-matrix interfaces were characterized using transmission and scanning electron microscopy (TEM and SEM). Mechanical properties were determined and compared to those obtained for uncoated Nicalon fiber-reinforced SiC.

Download Full-text

Morphological Characterization of Rhinacanthus Species of Sri Lanka

Planta Medica ◽

10.1055/s-0030-1251769 ◽

2010 ◽

Vol 76 (05) ◽

Author(s):

APPR Amarasinghe ◽

RP Karunagoda ◽

DSA Wijesundara

Keyword(s):

Sri Lanka ◽

Morphological Characterization

Download Full-text