Orientation distribution of polyvinyl alcohol fibers and its influence on bridging capacity and mechanical performances for high ductility cementitious composites

2020 ◽  
Vol 247 ◽  
pp. 118491 ◽  
Author(s):  
Cong Ding ◽  
Liping Guo ◽  
Bo Chen
Keyword(s):  
Polyvinyl Alcohol ◽  
Orientation Distribution ◽  
Cementitious Composites ◽  
High Ductility ◽  
Mechanical Performances

scholarly journals Polyvinyl Alcohol Fiber Length Optimization for High Ductility Cementitious Composites with Different Compressive Strength Grades

2021 ◽  
Vol 2021 ◽  
pp. 1-20
Author(s):  
Ding Cong ◽  
Guo Liping ◽  
Ren Jinming ◽  
Wang Yongming ◽  
Li Xinyu ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fiber Length ◽  
Interfacial Bonding ◽  
Cementitious Composites ◽  
High Ductility ◽  
Complementary Energy ◽  
Fiber Bridging ◽  
Bonding Properties ◽  
Fiber Matrix ◽  
Mechanical Performances

The fiber length has a significant impact on the fiber bridging capacity and the mechanical properties of high ductility cementitious composites (HDCCs), which is related to fiber/matrix interfacial bonding. However, this fundamental knowledge of HDCCs design has rarely been investigated systematically. To this end, this study deeply investigates the effect of the fiber length on the bridging stress and the complementary energy with various fiber/matrix interfacial bonds in theory. Then, the mechanical performances of HDCCs with various fiber lengths and compressive strengths were evaluated experimentally. In micromechanical design, longer fibers can achieve stronger bridging stress and more sufficient complementary energy regardless of the fiber/matrix interfacial bonding properties. However, it should be noted that the increase in bridging capacity was quite slow for the overlong fibers and excessive interfacial bonding. The experiments indicated that overlong fibers (18 mm and 24 mm) easily twined on the mixer blade and were hard to disperse evenly. The HDCCs with shorter fibers displayed better workability. The compressive strength was less affected by the fiber length, and most striking differences were less than 5.0%, while the flexural properties and the tensile properties first increased and then decreased when the fiber length ranged from 6 mm to 24 mm. Consequently, the fibers with lengths of 9 mm and the fibers with lengths of 12 mm were better candidates for the HDCCs with compressive strengths of 30 MPa to 80 MPa, and fibers with lengths of 9 mm caused the HDCCs to exhibit higher ductility properties in general.

scholarly journals Influence of polyvinyl alcohol fiber and fly ash content on compressive creep properties of high ductility cementitious composites

2021 ◽  
Vol 272 ◽  
pp. 02014
Author(s):  
Bo Chen ◽  
Liping Guo ◽  
Lihui Zhang ◽  
Wenxiao Zhang ◽  
Yin Bai ◽  
...  
Keyword(s):  
Fly Ash ◽  
Polyvinyl Alcohol ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Ash Content ◽  
Creep Model ◽  
High Ductility ◽  
Fiber Volume ◽  
Leading Role ◽  
Pva Fiber

The influence of polyvinyl alcohol (PVA) fiber volume fraction and fly ash content on the creep behavior of high ductility cementitious composites (HDCC) under compression was investigated. For this investigation, the creep behavior of four HDCC groups with cube compressive strength of 30–50 MPa, PVA fiber volume fraction of 1.5% and 2.0%, and fly ash content of 60% and 80% at 7 d and 28 d loading periods, respectively, were evaluated. A compressive creep model, which reflects the loading age and holding time, was established. The results revealed that when the load was applied at 7 d and 28 d, and then maintained for 245 d, the specific creep of HDCC ranged from 95×10-6/ MPa to 165×10-6/ MPa and from 59×10-6/ MPa to 135 × 10−6/ MPa, respectively. The corresponding creep coefficients ranged from 1.48 to 2.25 and from 1.10 to 1.94, respectively. The PVA fiber volume fraction and fly ash content were the main factors affecting the specific creep of HDCC, which increased with increasing fiber fraction and fly ash content. Under short-term loading, the fiber volume fraction played a leading role in the specific creep, and the fly ash content played the leading role during long-term loading. Furthermore, the specific creep and creep coefficient decreased significantly with increasing loading age. The classical creep model described by a power exponent function is suitable for HDCC.

Sign in / Sign up

Export Citation Format

Share Document