scholarly journals Numerical study of the effects of pin geometry and configuration in micro-pin-fin heat sinks for turbulent flows

2021 ◽  
pp. 101243
Author(s):  
Yacine Khetib ◽  
Khaled Sedraoui ◽  
Abdellataif Gari
Keyword(s):  
Turbulent Flows ◽  
Numerical Study ◽  
Heat Sinks ◽  
Pin Fin ◽  
Pin Geometry

Pin-Fin Heat Sink With Horizontal Base and Blocked Edges

2008 ◽  
Author(s):  
D. Sahray ◽  
H. Shmueli ◽  
N. Segal ◽  
G. Ziskind ◽  
R. Letan
Keyword(s):  
Heat Transfer ◽  
Free Convection ◽  
Contact Resistance ◽  
Cross Section ◽  
Heat Input ◽  
Heat Sink ◽  
Numerical Study ◽  
Heat Sinks ◽  
Transfer Enhancement ◽  
Pin Fin

In the present work, horizontal-base pin fin heat sinks exposed to free convection in air are studied. They are made of aluminum, and there is no contact resistance between the base and the fins. For the same base dimensions the fin height and pitch vary. The fins have a constant square cross-section. The edges of the sink are blocked: the surrounding insulation is flush with the fin tips. The effect of fin height and pitch on the performance of the sink is studied experimentally and numerically. In the experiments, the heat sinks are heated using foil electrical heaters. The heat input is set, and temperatures of the base and fins are measured. In the corresponding numerical study, the sinks and their environment are modeled using the Fluent 6 software. The results show that heat transfer enhancement due to the fins is not monotonic. The differences between sparsely and densely populated sinks are analyzed for various fin heights. Also assessed are effects of the blocked edges as compared to the previously studied cases where the sink edges were exposed to the surroundings.

Scale-Up and Generalization of Horizontal-Base Pin-Fin Heat Sinks in Natural Convection and Radiation

2010 ◽  
Vol 132 (11) ◽  
Author(s):  
D. Sahray ◽  
G. Ziskind ◽  
R. Letan
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Characteristic Length ◽  
Numerical Study ◽  
Scale Up ◽  
Heat Sinks ◽  
Transfer Enhancement ◽  
Numerical Investigations ◽  
Pin Fin ◽  
Base Size

This paper provides further insight in heat transfer from horizontal-base pin fin heat-sinks in free convection of air. The main objective is to assess the effect of base size, and this with regard to the effects of fin height and fin population density studied in a previous work (Sahray, D., et al., 2010, “Study and Optimization of Horizontal-Base Pin-Fin Heat Sinks in Natural Convection and Radiation,” ASME J. Heat Transfer, 132(012503), pp. 1–13). To this end, experimental and numerical investigations are performed with sinks of different base sizes. The sinks are made of aluminum, with no contact resistance between the base and the fins, and are heated using foil electrical heaters. In the corresponding numerical study, the sinks and their environment are modeled using the FLUENT 6.3 software. In the experiments, sink bases of 100×100 mm2 and 200×200 mm2 are used, while in the numerical study sinks of 50×50 mm2 are investigated, too. In addition to the sinks with exposed, free edges (Sahray, D., et al., 2010, “Study and Optimization of Horizontal-Base Pin-Fin Heat Sinks in Natural Convection and Radiation,” ASME J. Heat Transfer, 132(012503), pp. 1–13), the same sinks are explored also with their edges blocked. This is done in order to exclude the edge effect, thus making it possible to estimate heat transfer from a sink of an “infinite” base size. Heat-transfer enhancement due to the fins is assessed quantitatively and analyzed for various base sizes and fin heights. The effect of fin location in the array on its contribution to the heat-transfer rate from the sink is analyzed. By decoupling convection from radiation, a dimensional analysis of the results for natural convection is attempted. Interdependence of the base size and fin height effects on the heat transfer is demonstrated. A correlation that encompasses all the cases studied herein is obtained, in which the Nusselt number depends on the Rayleigh number, which uses the “clear” spacing between fins as the characteristic length, and on the dimensions of the fins and the base.

Optimization of Pin-Fin Heat Sinks Using the Two Medium Anisotropic Porous Model

2002 ◽  
Author(s):  
Seo Young Kim ◽  
Andrey V. Kuznetsov
Keyword(s):  
Heat Sink ◽  
Numerical Solutions ◽  
Solid Phase ◽  
Numerical Study ◽  
Heat Sinks ◽  
Thermal Dissipation ◽  
Uniform Heat Flux ◽  
Pin Fin ◽  
Geometric Conditions ◽  
Optimum Porosity

A numerical study has been carried out to optimize the thermal performance of a pin-fin heat sink. A pin-fin heat sink placed horizontally in a channel is modeled as a hydraulically and thermally anisotropic porous medium. A uniform heat flux is prescribed at the bottom of the heat sink. Cold air is supplied from the top opening of the channel and exhausts to the channel outlet. Comprehensive numerical solutions are derived from the governing Navier-Stokes and energy equations, using the Brinkman-Forchheimer extended Darcy model and the local thermal non-equilibrium (LTNE) model for the region of heat sink. Results from this study indicate that the anisotropy in permeability and solid-phase effective thermal conductivity changes substantially with the variation of porosity. The pin-fin heat sinks considered in the present study show an optimum porosity of 0.75<εopt<0.95 for maximum thermal dissipation depending on the flow and geometric conditions. Generally, a thick pin-fin displays a lower optimum porosity.

Effect of Fin Pitch and Height on Pin-Fin Heat Sink Performance

2008 ◽  
Author(s):  
D. Sahray ◽  
H. Shmueli ◽  
N. Segal ◽  
G. Ziskind ◽  
R. Letan
Keyword(s):  
Heat Transfer ◽  
Free Convection ◽  
Contact Resistance ◽  
Cross Section ◽  
Heat Input ◽  
Heat Sink ◽  
Numerical Study ◽  
Heat Sinks ◽  
Transfer Enhancement ◽  
Pin Fin

In the present work, horizontal-base pin fin heat sinks exposed to free convection in air are studied. They are made of aluminum, and there is no contact resistance between the base and the fins. The sinks have the same base dimensions whereas the fin height and pitch vary. The fins have a constant square cross-section. The effect of fin height and pitch on the performance of the sink is studied experimentally and numerically. In the experiments, the heat sinks are heated using foil electrical heaters. The heat input is set, and temperatures of the base and fins are measured. In the corresponding numerical study, the sinks and their environment are modeled using the Fluent 6.3 software. The results show that heat transfer enhancement due to the fins is not monotonic. The differences between sparsely and densely populated sinks are analyzed for various fin heights.

Implementations of Deflectors to Improve the Performance of Heat Sinks

2012 ◽  
Author(s):  
J. P. Ramirez-Vazquez ◽  
A. Hernandez-Guerrero ◽  
J. L. Zuñiga-Cerroblanco ◽  
J. C. Rubio-Arana
Keyword(s):  
Heat Sink ◽  
Numerical Study ◽  
Electronic Devices ◽  
Constant Heat Flux ◽  
Heat Fluxes ◽  
Heat Sinks ◽  
Hydrodynamic Behavior ◽  
Constant Heat ◽  
Pin Fin ◽  
Global Performance

This work presents a numerical study of the thermal and hydrodynamic behavior of a pin-fin heat sink where deflectors are placed along the flow of the coolant air; the effect of the arrangement of the fins and deflectors in the global performance of the heat sink is investigated. The fin geometry analyzed is rectangular, and the arrangement of the fins is inline. The heat sink is placed in a channel in which air flows, and a constant heat flux is applied at the bottom wall of the heat sink with values equivalent to the heat fluxes generated by current electronic devices. Deflectors are placed in the top of the channel in order to drive the air flow into the front and end of the heat sink. The results for the Nusselt number and for the pressure drop along the heat sink are reported. The best dimension of deflectors and pitch for the arrangement based on the thermal and hydraulic performance is attained.

Study of Horizontal-Base Pin-Fin Heat Sinks in Natural Convection

2007 ◽  
Author(s):  
D. Sahray ◽  
R. Magril ◽  
V. Dubovsky ◽  
G. Ziskind ◽  
R. Letan
Keyword(s):  
Heat Transfer ◽  
Transfer Rate ◽  
Characteristic Length ◽  
Numerical Study ◽  
Heat Sinks ◽  
Transfer Enhancement ◽  
Total Heat Transfer ◽  
Pin Fin ◽  
Relative Contribution ◽  
Fin Spacing

The present paper deals with horizontal-base pin fin heat sinks in free convection. The sinks have the same base dimensions and variable fin pitch. They are made of aluminum, and there is no contact resistance between the base and the fins. The fins have a constant square cross-section. The effect of fin pitch on the performance of the sink is studied experimentally and numerically. In the experiments, the heat sinks are heated using foil electrical heaters. The heat input is set, and temperatures of the base and fins are measured. In the corresponding numerical study, the sinks are modeled using the Fluent 6 software. The results show that heat transfer enhancement due to the fins is not monotonic. The differences between sparsely and densely populated sinks are analyzed. Also analyzed are the effects of the sink edges on the total heat transfer. A relative contribution of outer and inner fin rows in the sink is assessed, together with the effect of fin location in the array on the heat transfer rate from an individual fin. Dimensional analysis of the results is attempted, and a correlation presenting the Nusselt number vs. the Rayleigh number is suggested, where the inter-fin spacing serves as the characteristic length.

Study and Optimization of Horizontal-Base Pin-Fin Heat Sinks in Natural Convection and Radiation

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
D. Sahray ◽  
H. Shmueli ◽  
G. Ziskind ◽  
R. Letan
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Flux Distribution ◽  
Characteristic Length ◽  
Numerical Study ◽  
Heat Sinks ◽  
Heat Flux Distribution ◽  
Transfer Enhancement ◽  
Pin Fin ◽  
Relative Contribution

This paper aims at deeper understanding of heat transfer from horizontal-base pin-fin heat sinks with exposed edges in free convection of air. The effects of fin height and fin population density are studied experimentally and numerically. The sinks are made of aluminum, and there is no contact resistance between the base and the fins. All the sinks studied have the same base dimensions and are heated using foil electrical heaters. The fins have a constant square cross section, whereas the fin height and pitch vary. The heat input is set, and temperatures of the base and fins are measured. In the corresponding numerical study, the sinks and their environment are modeled using the FLUENT 6.3 software. The results show that heat-transfer enhancement due to the fins is not monotonic. The differences between sparsely and densely populated sinks are assessed quantitatively and analyzed for various fin heights. Also analyzed is the heat flux distribution at the edges and center of the sink. A relative contribution of outer and inner fin rows in the sink is assessed, together with the effect of fin location in the array on the heat-transfer rate from an individual fin. By decoupling convection from radiation, a dimensional analysis of the results for natural convection is attempted. A correlation presenting the Nusselt number versus the Rayleigh number is suggested, where the “clear” spacing between fins serves as the characteristic length.

Sign in / Sign up

Export Citation Format

Share Document