scholarly journals Growth, yield and arsenic accumulation by wheat grown in a pressmud amended salt-affected soil irrigated with arsenic contaminated water

2021 ◽  
Vol 224 ◽  
pp. 112692
Author(s):  
Muhammad Imran ◽  
Muhammad Ashraf ◽  
Abdul Rasul Awan
2016 ◽  
Vol 28 (2) ◽  
pp. 171-180 ◽  
Author(s):  
Sharmin Sultana ◽  
Md Harunur Rashid ◽  
SM Imamul Huq

A pot experiment was conducted to study the transfer of arsenic (As) from soil to plant and to know the relation between arsenic accumulation and water requirement. The plants BR-29, BR-28, Red amaranthus (Lalshak) and Ipomoea aquatica (Kalmishak) were selected for this experiment. The control pots were irrigated with tap water and the treatment pots were irrigated with arsenic contaminated water. Different plant parts such as roots, straw, leaf and seeds of rice and roots, shoots, leaves of Lalshak and Kalmishak were analyzed. It was found that arsenic concentration was higher in the plants that were irrigated with arsenic contaminated water. Maximum arsenic concentration was found in roots and the minimum in leaves. The arsenic accumulation depended on the type of crops and varieties. The present study revealed that arsenic accumulation is higher in those plants that have higher water requirement. BR-29 needs more water than BR-28 and as a result BR-29 accumulated more arsenic than BR-28. Similarly Ipomoea aquatica accumulated more arsenic than Red amaranthus. From the experiment it was concluded that if irrigation is continued with arsenic contaminated water for a long time, arsenic may enter into the food chain beyond permissible limit and may cause human health risk.Bangladesh J. Sci. Res. 28(2): 171-180, Dec-2015


2021 ◽  
Author(s):  
Muhammad Awais Piracha ◽  
Muhammad Ashraf ◽  
Sher Muhammad Shahzad ◽  
Muhammad Saleem Arif ◽  
Muhammad Shahid Rizwan ◽  
...  

Abstract Being analogue to arsenic (As), phosphorus (P) may affect As dynamics in soil and toxicity to plants depending upon many soil and plant factors. Two sets of experiments were conducted to determine the effect of P on As fractionation in soils, its accumulation by plants and subsequent impact on growth, yield and physiological characteristics of sunflower (Helianthus annuus L.). Experimental plan comprised of two As levels (60 and 120 mg As kg-1 soil), four P (0-5-10-20 g phosphate rock kg-1 soil) and three textural types (sandy, loamy and clayey) with three replications. Among different As fractions determined, labile, calcium-bound, organic matter-bound and residual As increased while iron-bound and aluminum-bound As decreased with increasing P in all the three textural types. Labile-As percentage increased in the presence of P by 16.9-48.0% at As60 while 36.0-68.1% at As120 in sandy, 19.1-64.0% at As60 while 11.5-52.3% at As120 in loamy, and 21.8-58.2% at As60 while 22.3-70.0% at As120 in clayey soil compared to respective As treatment without P. Arsenic accumulation in plant tissues at both contamination levels declined with P addition as evidenced by lower bioconcentration factor. Phosphorus mitigated the As-induced oxidative stress expressed in term of reduced hydrogen peroxide, malondialdehyde while increased glutathione, and consequently improved the achene yield. Although, P increased As solubility in soil but restricted its accumulation in plant tissues, leading to reversal of oxidative damage and improved sunflower growth and yield in all the three soil textural types, more profound effect in sandy texture.


2020 ◽  
pp. 15-27

In order to study the effect of phosphogypsum and humic acids in the kinetic release of salt from salt-affected soil, a laboratory experiment was conducted in which columns made from solid polyethylene were 60.0 cm high and 7.1 cm in diameter. The columns were filled with soil so that the depth of the soil was 30 cm inside the column, the experiment included two factors, the first factor was phosphogypsum and was added at levels 0, 5, 10 and 15 tons ha-1 and the second-factor humic acids were added at levels 0, 50, 100 and 150 kg ha-1 by mixing them with the first 5 cm of column soil and one repeater per treatment. The continuous leaching method was used by using an electrolytic well water 2.72 dS m-1. Collect the leachate daily and continue the leaching process until the arrival of the electrical conductivity of the filtration of leaching up to 3-5 dS m-1. The electrical conductivity and the concentration of positive dissolved ions (Ca, Mg, Na) were estimated in leachate and the sodium adsorption ratio (SAR) was calculated. The results showed that the best equation for describing release kinetics of the salts and sodium adsorption ratio in soil over time is the diffusion equation. Increasing the level of addition of phosphogypsum and humic acids increased the constant release velocity (K) of salts and the sodium adsorption ratio. The interaction between phosphogypsum and humic acids was also affected by the constant release velocity of salts and the sodium adsorption ratio. The constant release velocity (K) of the salts and the sodium adsorption ratio at any level of addition of phosphogypsum increased with the addition of humic acids. The highest salts release rate was 216.57 in PG3HA3, while the lowest rate was 149.48 in PG0HA0. The highest release rate of sodium adsorption ratio was 206.09 in PG3HA3, while the lowest rate was 117.23 in PG0HA0.


Author(s):  
Seroor Atalah Khaleefa Alia ◽  
Dr. Mohammed Ibrahimb ◽  
Hussein Ali Hussein

Adsorption is most commonly applied process for the removal of pollutants such as dyes and heavy metals ions from wastewater. The present work talks about preparing graphenic material attached sand grains called graphene sand composite (GSC) by using ordinary sugar as a carbon source. Physical morphology and chemical composition of GSC was examined by using (FTIR, SEM, EDAX and XRD). Efficiency of GSC in the adsorption of organic dyes from water was investigated using reactive green dye with different parameters such as (ph, temperature, contact time and dose). Adsorption isotherm was also studied and the results showed that the maximum adsorption capacity of dye is 28.98 mg/g. This fast, low-cost process can be used to manufacture commercial filters to treat contaminated water using appropriate engineering designs.


Sign in / Sign up

Export Citation Format

Share Document