Hydrocarbon emission control of a hydrocarbon adsorber and converter under cold start of the gasoline engine

Energy ◽  
2022 ◽  
Vol 239 ◽  
pp. 122138
Author(s):  
Changling Feng ◽  
Yuanwang Deng ◽  
Lehan Chen ◽  
Wei Han ◽  
Jiaqiang E ◽  
...  
2016 ◽  
Vol 41 (40) ◽  
pp. 18273-18281 ◽  
Author(s):  
Lijun Hao ◽  
Xiaoliu Xu ◽  
Xiaonian Guo ◽  
Changwei Ji ◽  
Xin Wang ◽  
...  

Energy ◽  
2019 ◽  
Vol 183 ◽  
pp. 869-879 ◽  
Author(s):  
Yuanwang Deng ◽  
Changling Feng ◽  
Jiaqiang E ◽  
Kexiang Wei ◽  
Bin Zhang ◽  
...  

Fuel ◽  
2021 ◽  
pp. 122661
Author(s):  
Changling Feng ◽  
Yuanwang Deng ◽  
Yan Tan ◽  
Wei Han ◽  
Jiaqiang E ◽  
...  

2021 ◽  
pp. 1-11
Author(s):  
Dominik Appel ◽  
Fabian P. Hagen ◽  
Uwe Wagner ◽  
Thomas Koch ◽  
Henning Bockhorn ◽  
...  

Abstract To comply with future emission regulations for internal combustion engines, system-related cold-start conditions in short-distance traffic constitute a particular challenge. Under these conditions, pollutant emissions are seriously increased due to internal engine effects and unfavorable operating conditions of the exhaust aftertreatment systems. As a secondary effect, the composition of the exhaust gases has a considerable influence on the deposition of aerosols via different deposition mechanisms and on fouling processes of exhaust gas-carrying components. Also, the performance of exhaust gas aftertreatment systems may be affected disadvantageously. In this study, the exhaust gas and deposit composition of a turbocharged three-cylinder gasoline engine is examined in-situ upstream of the catalytic converter at ambient and engine starting temperatures of -22 °C to 23 °C using a Fourier-transform infrared spectrometer and a particle spectrometer. For the cold start investigation, a modern gasoline engine with series engine periphery is used. In particular, the investigation of the behavior of deposits in the exhaust system of gasoline engines during cold start under dynamic driving conditions represents an extraordinary challenge due to an average lower soot concentration in the exhaust gas compared to diesel engines and so far, has not been examined in this form. A novel sampling method allows ex-situ analysis of formed deposits during a single driving cycle. Both, particle number concentration and the deposition rate are higher in the testing procedure of Real Driving Emissions (RDE) than in the inner-city part of the Worldwide harmonized Light vehicles Test Cycle (WLTC). In addition, reduced ambient temperatures increase the amount of deposits, which consist predominantly of soot and to a minor fraction of volatile compounds. Although the primary particle size distributions of the deposited soot particles do not change when boundary conditions change, the degree of graphitization within the particles increases with increasing exhaust gas temperature.


2021 ◽  
Vol 11 (1) ◽  
pp. 425-434
Author(s):  
Jacek Pielecha ◽  
Kinga Skobiej ◽  
Karolina Kurtyka

Abstract In order to better reflect the actual ecological performance of vehicles in traffic conditions, both the emission standards and the applied emission tests are being developed, for example by considering exhaust emissions for a cold engine start. This article presents the research results on the impact of ambient temperature during the cold start of a gasoline engine in road emission tests. The Real Driving Emissions (RDE) tests apply to passenger cars that meet the Euro 6 emissions norm and they are complementary to their type approval tests. A portable emissions measurement system was used to record the engine and vehicle operating parameters, as well as to measure the exhaust emissions during tests. This allowed for parameters such as engine load, engine speed and vehicle speed to be monitored. The cold start conditions for two different temperatures (8°C and 25°C) were compared in detail. Moreover, the engine operating parameters, exhaust concentration values and road emissions for the 300 s time interval, were compared. The summary of the article presents the share of a passenger car’s cold start phase for each exhaust compound in the urban part of the test and in the entire Real Driving Emissions test depending on the ambient temperature.


2004 ◽  
Vol 2004.79 (0) ◽  
pp. _6-1_-_6-2_
Author(s):  
Masahito SUGAWARA ◽  
Fumiteru AKAMATSU ◽  
Masashi KATSUKI ◽  
Takeshi SERIZAWA

2011 ◽  
Vol 378-379 ◽  
pp. 401-404
Author(s):  
Xiang Ming Qiao ◽  
An Xu

To analyse and research the idle hydrocarbon emission regularity of passenger car gasoline engine, based on large sample detected data of different type cars, parameter estimation and hypothesis test are carried on by statistical tools and neans, and the optimum distribution parameters of idle hydrocarbon emission of different type engines are also got. Then the optimum distribution models of these engines are established. The calculating result shows that the maximum error between model calculating and sample detecting certification rates is only 0.526 8%, and the established models have very high calculating precision and practical value. On the other hand, the research also shows that the inspect and maintenance program should be strengthen in order to control vehicle emission pollution effectively.


2012 ◽  
Vol 433-440 ◽  
pp. 6390-6396
Author(s):  
Pei Yong Ni ◽  
Xiang Li Wang

The reduction of sauter mean diameter (SMD) of droplets means the percent of the evaporated fuel, which is important to the formation of the combustible mixture in a port-injection gasoline engine during cold-start. Three-dimensional numerical simulation of SMD of the droplets in the inlet port of a gasoline engine was employed using the CFD software. This paper presented the effect of multi-parameters on SMD of the droplets including initial droplet velocity, intake temperature, fuel temperature, injection timing and engine speed. The simulation results show that the most influential parameters on SMD of the droplets are intake temperature and fuel temperature. The fuel evaporation rates increase approximately linearly with the intake air temperature and fuel temperature increasing. The initial droplet velocity and injection timing have a little effect on the fuel evaporation. As engine speed increases, SMD of the droplets firstly decreases and then increases. After intake-valve-open (IVO), back flow of gas in cylinders results in steep reduction of droplet diameter.


Sign in / Sign up

Export Citation Format

Share Document