Simulation of a block impacting a reinforced concrete slab with a finite element model and a mass-spring system

2007 ◽  
Vol 29 (11) ◽  
pp. 2844-2852 ◽  
Author(s):  
F. Delhomme ◽  
M. Mommessin ◽  
J.P. Mougin ◽  
P. Perrotin
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Concrete Slab ◽  
Element Model ◽  
Reinforced Concrete Slab ◽  
Spring System ◽  
Mass Spring

scholarly journals Finite element analysis of flexural behavior of textile reinforced concrete slab

2021 ◽  
Vol 261 ◽  
pp. 02042
Author(s):  
Mingqiu Xu ◽  
Jianhua Shao ◽  
Baijian Tang ◽  
Hongming Li
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Concrete Slab ◽  
Element Model ◽  
Flexural Behavior ◽  
Textile Reinforced Concrete ◽  
Reinforced Concrete Slab ◽  
Element Analysis ◽  
Bending Load

Order to investigate the failure effect of textile reinforced concrete (TRC) plate under bending load, the corresponding finite element model is established. By comparing the numerical simulation results with the experimental results, the rationality and feasibility of the finite element model are verified, and then the crack extension of TRC and the ultimate strain of carbon textile are analyzed. The failure mode of the slab under bending load is obtained, and it is found that the carbon textile concrete slab has better reinforcement effect, which greatly improves the safety performance of concrete members.

Uniform loading on the reinforced concrete beam produced by the specific cylinder-shaped rubber bags fully filled with air or water

2020 ◽  
Vol 23 (9) ◽  
pp. 1934-1947
Author(s):  
Dapeng Chen ◽  
Li Chen ◽  
Qin Fang ◽  
Yuzhou Zheng ◽  
Teng Pan
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Element Model ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Uniform Loading ◽  
Air Bag

The bending behavior of reinforced concrete beams under uniform pressure is critical for the research of the blast-resistance performance of structural components under explosive loads. In this study, a bending test of five reinforced concrete beams with the dimensions of 200 mm (width) × 200 mm (depth) × 2500 mm (length) under uniform load produced by a specific cylinder-shaped rubber bag filled with air or water was conducted to investigate their flexural performances. An air bag load was applied to three of the reinforced concrete beams, a water bag load was applied to one reinforced concrete beam, and the remainder beam was subjected to the 4-point bending load. The experimental results highlighted that the air bag and water bag loading methods can be used to effectively apply uniform loads to reinforced concrete beams. Moreover, the stiffness of the air bag was improved by 123% in accordance with the initial pressure increases from 0.15 to 0.45 MPa. In addition, a finite element model of the test loading system was established using ABAQUS/Standard software. Moreover, the critical factors of the air bag loading method were analyzed using the numerical model. The calculated results were found to be in good agreement with the test data. The established finite element model can therefore be used to accurately simulate the action performances of the uniform loading technique using rubber bags filled with air or water.

A materially nonlinear finite element model for the analysis of curved reinforced concrete box-girder bridges

1993 ◽  
Vol 20 (5) ◽  
pp. 754-759 ◽  
Author(s):  
S. F. Ng ◽  
M. S. Cheung ◽  
J. Q. Zhao
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Element Model ◽  
Nonlinear Material ◽  
Box Girder Bridges ◽  
Box Girder ◽  
Girder Bridges ◽  
Concrete Box Girder ◽  
Concrete Box Girder Bridges

A layered finite element model with material nonlinearity is developed to trace the nonlinear response of horizontally curved reinforced concrete box-girder bridges. Concrete is treated as an orthotropic nonlinear material and reinforcement is modeled as an elastoplastic strain-hardening material. Due to the fact that the flanges and webs of the structure are much different both in configuration and in the state of stresses, two types of facet shell elements, namely, the triangular generalized conforming element and the rectangular nonconforming element, are adopted to model them separately. A numerical example of a multi-cell box-girder bridge is given and the results are compared favourably with the experimental results previously obtained. Key words: finite element method, curved box-girder bridges, reinforced concrete, nonlinear analysis.

Calculation of Reinforced Concrete Prismatic Shells by the Finite Element Method Using Variable Elasticity Parameters

2019 ◽  
Vol 945 ◽  
pp. 969-974
Author(s):  
V. Kruglov ◽  
V. Iurchenko
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Elements ◽  
Concrete Slab ◽  
Volume Ratio ◽  
High Strength ◽  
Finite Elements Method ◽  
Software Module ◽  
Reinforced Concrete Slab ◽  
Elastic Characteristics

The paper considers the modification of the generally accepted formulation of the finite elements method by applying in the calculation I.Mileykovski’s refined technical theory of shells that takes into account the deformations of the transverse shear along the thickness of the model. When applying this solution path, it is possible to calculate thick and thin shells (plates) with equal efficiency, taking into account the complex strained state of an anisotropic material. It illustrates the inclusion in the computational algorithm of variable parameters of the elasticity of concrete, allowing more accurate evaluation of the stress-strain state in the finite element under complex (combined) loads. The presence of reinforcement in the material is modeled by dividing the structure into layers and sequentially reduction the elastic characteristics of the material based on the volume ratio of the components. The advantage of the algorithm is the ease of its integration with the conventional finite elements method. All transformations in this case consist in the modification of expressions for determining the elastic characteristics of the construction, calculating the gradient and stiffness matrices, while the sequence of further calculations does not change. This enables to use the proposed algorithm, including as a plug-in software module, expanding the capabilities of existing computing programs. The article demonstrates the application of the method in modeling a reinforced concrete slab made with the use of multi-component high-strength concrete of a heavy class having a prismatic strength under uniaxial compression of more than 110 MPa.

Microcomputer analysis of reinforced concrete slab systems

1993 ◽  
Vol 20 (4) ◽  
pp. 587-601 ◽  
Author(s):  
Pierre Léger ◽  
Patrick Paultre
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Structural Design ◽  
Concrete Slab ◽  
Three Dimensional ◽  
Structural Behaviour ◽  
Reinforced Concrete Slab ◽  
Element Analysis ◽  
Equivalent Frame ◽  
Frame Method

Microcomputer finite element analysis of reinforced concrete slab systems can now be routinely performed to produce realistic numerical simulation of three-dimensional structural behaviour. However, an efficient use of this approach requires an automated integration of design and analysis procedures. Guidelines for proper finite element modelling of slab systems are first presented along with simple post-processing algorithms to perform automatically the design or verifications from the analytical results. Numerical applications on simple slab systems subjected to uniform and concentrated loads are then used to illustrate the relative performance between finite element analyses and the equivalent frame method. Key words: microcomputer, reinforced concrete slab, finite element method, structural design.

Sign in / Sign up

Export Citation Format

Share Document