Effects of advanced injection timing and inducted gaseous fuel on performance, combustion and emission characteristics of a diesel engine operated in dual-fuel mode

Fuel ◽  
2022 ◽  
Vol 310 ◽  
pp. 122232
Author(s):  
Swarup Kumar Nayak ◽  
Anh Tuan Hoang ◽  
Sandro Nižetić ◽  
Xuan Phuong Nguyen ◽  
Tri Hieu Le
Keyword(s):  
Diesel Engine ◽  
Gaseous Fuel ◽  
Dual Fuel ◽  
Injection Timing ◽  
Emission Characteristics

scholarly journals Hydrogen Injection in a Dual Fuel Engine Fueled with Low-Pressure Injection of Methyl Ester of Thevetia Peruviana (METP) for Diesel Engine Maintenance Application

Energies ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 5663 ◽  
Author(s):  
Mahantesh Marikatti ◽  
N. R. Banapurmath ◽  
V. S. Yaliwal ◽  
Y.H. Basavarajappa ◽  
Manzoore Elahi M Soudagar ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Gas Flow ◽  
Engine Performance ◽  
Gaseous Fuel ◽  
Dual Fuel ◽  
Injection Timing ◽  
Thevetia Peruviana ◽  
Oil Source ◽  
Engine Maintenance

The present work is mapped to scrutinize the consequence of biodiesel and gaseous fuel properties, and their impact on compression-ignition (CI) engine combustion and emission characteristics in single and dual fuel operation. Biodiesel prepared from non-edible oil source derived from Thevetia peruviana belonging to the plant family of Apocynaceaeis. The fuel has been referred as methyl ester of Thevetia peruviana (METP) and adopted as pilot fuel for the effective combustion of compressed gaseous fuel of hydrogen. This investigation is an effort to augment the engine performance of a biodiesel-gaseous fueled diesel engine operated under varied engine parameters. Subsequently, consequences of gas flow rate, injection timing, gas entry type, and manifold gas injection on the modified dual-fuel engine using conventional mechanical fuel injections (CMFIS) for optimum engine performance were investigated. Fuel consumption, CO, UHC, and smoke formations are spotted to be less besides higher NOx emissions compared to CMFIS operation. The fuel burning features such as ignition delay, burning interval, and variation of pressure and heat release rates with crank angle are scrutinized and compared with base fuel. Sustained research in this direction can convey practical engine technology, concerning fuel combinations in the dual fuel mode, paving the way to alternatives which counter the continued fossil fuel utilization that has detrimental impacts on the climate.

Experimental Studies of Biogas in a Single Cylinder Diesel Engine by Dual Fuel Mode of Operation

2019 ◽  
Vol 895 ◽  
pp. 109-114 ◽  
Author(s):  
C. Jagadish ◽  
Gumtapure Veershetty
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Experimental Studies ◽  
Experimental Result ◽  
Dual Fuel ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Single Cylinder ◽  
Full Load ◽  
Injection Water

The aim of this work is to examine the performance, combustion as well as emission characteristics of diesel engine performed for various mixtures of methane-enriched biogas (95% CH4). Experiments were performed on a single cylinder, four-stroke constant speed, direct injection, water-cooled diesel engine. The engine is operated by means of dual fuel mode using diesel and different mixtures of methane-enriched biogas (BG) like BG10, BG20, BG30, and BG40 mixed with the air (i.e. BG40-40% of CH4 by volume respectively) for different loads and at injection timing of 27.5° before top dead centre (bTDC). The performance, combustion and emission characteristics of the engine operated by dual fuel mode were experimentally analyzed, and compared with respect to diesel mode. The experimental result reveals that better performance and lower emissions were observed for BG40 compared to other mixtures. The brake thermal efficiency of BG40 is lower by 2.43% compared to diesel at full load. The cylinder peak pressure for dual fuel mode is higher by 6.55% when compared with diesel mode. NOx emission reduced by 2.6 % and CO emission increased by 3.3% compared to diesel at full load respectively. Keywords: Biogas, Energy, Combustion, Emission, Injection timing, dual fuel mode

scholarly journals A Numerical Study on the Combustion Process and Emission Characteristics of a Natural Gas-Diesel Dual-Fuel Marine Engine at Full Load

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1342
Author(s):  
Van Chien Pham ◽  
Jae-Hyuk Choi ◽  
Beom-Seok Rho ◽  
Jun-Soo Kim ◽  
Kyunam Park ◽  
...  
Keyword(s):  
Natural Gas ◽  
Combustion Process ◽  
Simulation Software ◽  
Dual Fuel ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Cylinder Pressure ◽  
Marine Engine ◽  
Full Load ◽  
Simulation Results

This paper presents research on the combustion and emission characteristics of a four-stroke Natural gas–Diesel dual-fuel marine engine at full load. The AVL FIRE R2018a (AVL List GmbH, Graz, Austria) simulation software was used to conduct three-dimensional simulations of the combustion process and emission formations inside the engine cylinder in both diesel and dual-fuel mode to analyze the in-cylinder pressure, temperature, and emission characteristics. The simulation results were then compared and showed a good agreement with the measured values reported in the engine’s shop test technical data. The simulation results showed reductions in the in-cylinder pressure and temperature peaks by 1.7% and 6.75%, while NO, soot, CO, and CO2 emissions were reduced up to 96%, 96%, 86%, and 15.9%, respectively, in the dual-fuel mode in comparison with the diesel mode. The results also show better and more uniform combustion at the late stage of the combustions inside the cylinder when operating the engine in the dual-fuel mode. Analyzing the emission characteristics and the engine performance when the injection timing varies shows that, operating the engine in the dual-fuel mode with an injection timing of 12 crank angle degrees before the top dead center is the best solution to reduce emissions while keeping the optimal engine power.

A phenomenological combustion analysis of a dual-fuel natural-gas diesel engine

2016 ◽  
Vol 231 (1) ◽  
pp. 66-83 ◽  
Author(s):  
Shuonan Xu ◽  
David Anderson ◽  
Mark Hoffman ◽  
Robert Prucka ◽  
Zoran Filipi
Keyword(s):  
Diesel Engine ◽  
Natural Gas ◽  
Heat Release ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Dual Fuel ◽  
Injection Timing ◽  
Heavy Duty ◽  
Engine System ◽  
Wiebe Function

Energy security concerns and an abundant supply of natural gas in the USA provide the impetus for engine designers to consider alternative gaseous fuels in the existing engines. The dual-fuel natural-gas diesel engine concept is attractive because of the minimal design changes, the ability to preserve a high compression ratio of the baseline diesel, and the lack of range anxiety. However, the increased complexity of a dual-fuel engine poses challenges, including the knock limit at a high load, the combustion instability at a low load, and the transient response of an engine with directly injected diesel fuel and port fuel injection of compressed natural gas upstream of the intake manifold. Predictive simulations of the complete engine system are an invaluable tool for investigations of these conditions and development of dual-fuel control strategies. This paper presents the development of a phenomenological combustion model of a heavy-duty dual-fuel engine, aided by insights from experimental data. Heat release analysis is carried out first, using the cylinder pressure data acquired with both diesel-only and dual-fuel (diesel and natural gas) combustion over a wide operating range. A diesel injection timing correlation based on the injector solenoid valve pulse widths is developed, enabling the diesel fuel start of injection to be detected without extra sensors on the fuel injection cam. The experimental heat release trends are obtained with a hybrid triple-Wiebe function for both diesel-only operation and dual-fuel operation. The ignition delay period of dual-fuel operation is examined and estimated with a predictive correlation using the concept of a pseudo-diesel equivalence ratio. A four-stage combustion mechanism is discussed, and it is shown that a triple-Wiebe function has the ability to represent all stages of dual-fuel combustion. This creates a critical building block for modeling a heavy-duty dual-fuel turbocharged engine system.

Emission Characteristics from Diesel Engine with Emulsion Fuel and Natural Gas Dual Fuel

2021 ◽  
Vol 25 (5) ◽  
pp. 22-28
Author(s):  
Suk-Ho Jung ◽  
Ji-Ho Kim ◽  
Sang-Won Kim ◽  
Jeong-Min Cheon
Keyword(s):  
Diesel Engine ◽  
Natural Gas ◽  
Dual Fuel ◽  
Emission Characteristics

scholarly journals Effect of Partially Premixed Fuel on Performance and Emission Characteristics of Compression Ignition (CI) Engine

2019 ◽  
Vol 8 (4S2) ◽  
pp. 163-166
Keyword(s):  
Diesel Engine ◽  
New Technology ◽  
Control Unit ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Compression Ignition ◽  
Fuel Injector ◽  
Si Engine ◽  
Performance And Emission ◽  
Partially Premixed

In this world, the population is increased and the number of vehicles increased. Not only population the pollution is increased lot by vehicles in the world harmful pollutant is realized from the vehicles like CO, HC, NOx and smoke particulates. It is inevitable to find some new technology, which increases the better performance and emission characteristics. Partially premixed compression ignition (PCCI) is the best technology for the reducing of harmful pollution in the vehicle, which uses the diesel as fuel it, gives the advantages of both CI and SI engine. This paper investigates the performance and emission characteristics of partially premixed diesel engine. Diesel engine has two injectors of port fuel injector (PFI) and direct injector (DI) to inject the fuel in different timing and electrical control unit (ECU) passes the power to PFI; it can control the injection timing and increases the fuel content from the fuel pump. The main aim in this paper is studied is effect of partially premixed ratio, performance of engine and emission characteristics of diesel engine

Sign in / Sign up

Export Citation Format

Share Document