Characterization of the soft zone in dissimilar welds joint of 2.25Cr-1Mo and lean duplex LDX2101 steel

The aim of this investigation is to study the fracture location as well as mechanical properties of weldments from elevated temperature tensile test in T22/T91 dissimilar joining by GTAW process. Two configurations of welding procedures are used: ER90S-B9 and ER90S-B3. Postweld heat treatment (PWHT) is carried out at 760°C for 30 minutes. The results demonstrate that the higher tested temperature, the lower the strength of welded sample; nevertheless, the greater the ductility of welded sample, except ER90S-B9 welded samples tested at 650°C. The fracture of both configurations tested at 550°C and 750°C occurs at T22 BM and T91 HAZ, respectively. At these temperatures, the fracture surfaces mainly reveal dimple ductile mode corresponding to mechanical properties’ results. On the contrary, the failure tested at 650°C occurs at T22 HAZ (Soft zone) and T91 HAZ of ER90S-B9 and ER90S-B3 welded samples, respectively. The mechanical properties’ results at this temperature are relatively different. The combination of brittle and dimple mode at the edge of samples is observed on the ER90S-B9 welded samples corresponding to low ductility at this temperature. Whereas samples welded by ER90S-B3 show only dimple ductile mode. The results exhibit that the fracture location could be affected by the configuration of T22/T91 dissimilar welding.

Download Full-text

Morphological Characterization of Mycobacteriophage R1

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100051281 ◽

1974 ◽

Vol 32 ◽

pp. 254-255

Author(s):

B. L. Soloff ◽

T. A. Rado

Keyword(s):

Carbon Source ◽

Stationary Phase ◽

Growth Phase ◽

Minimal Medium ◽

Morphological Characterization ◽

Logarithmic Growth Phase ◽

Complete Lysis ◽

Lysogenic Culture ◽

Logarithmic Growth

Mycobacteriophage R1 was originally isolated from a lysogenic culture of M. butyricum. The virus was propagated on a leucine-requiring derivative of M. smegmatis, 607 leu−, isolated by nitrosoguanidine mutagenesis of typestrain ATCC 607. Growth was accomplished in a minimal medium containing glycerol and glucose as carbon source and enriched by the addition of 80 μg/ ml L-leucine. Bacteria in early logarithmic growth phase were infected with virus at a multiplicity of 5, and incubated with aeration for 8 hours. The partially lysed suspension was diluted 1:10 in growth medium and incubated for a further 8 hours. This permitted stationary phase cells to re-enter logarithmic growth and resulted in complete lysis of the culture.

Download Full-text

AEM analysis of crystallization in Ti-based amorphous alloys

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100075142 ◽

1983 ◽

Vol 41 ◽

pp. 270-271

Author(s):

A.R. Pelton ◽

A.F. Marshall ◽

Y.S. Lee

Keyword(s):

Magnetic Properties ◽

Amorphous Alloys ◽

Amorphous Materials ◽

Isothermal Annealing ◽

Amorphous Matrix ◽

Nucleation And Growth ◽

Current Interest ◽

Amorphous Films ◽

Electrical And Magnetic Properties

Amorphous materials are of current interest due to their desirable mechanical, electrical and magnetic properties. Furthermore, crystallizing amorphous alloys provides an avenue for discerning sequential and competitive phases thus allowing access to otherwise inaccessible crystalline structures. Previous studies have shown the benefits of using AEM to determine crystal structures and compositions of partially crystallized alloys. The present paper will discuss the AEM characterization of crystallized Cu-Ti and Ni-Ti amorphous films.Cu60Ti40: The amorphous alloy Cu60Ti40, when continuously heated, forms a simple intermediate, macrocrystalline phase which then transforms to the ordered, equilibrium Cu3Ti2 phase. However, contrary to what one would expect from kinetic considerations, isothermal annealing below the isochronal crystallization temperature results in direct nucleation and growth of Cu3Ti2 from the amorphous matrix.

Download Full-text

Characterization of Coherent, Ordered Precipitates in Nickel-Base Alloys

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100071168 ◽

1973 ◽

Vol 31 ◽

pp. 144-145

Author(s):

B. H. Kear ◽

J. M. Oblak

Keyword(s):

Stable Phase ◽

Nickel Base Superalloy ◽

Alloy 718 ◽

Commercial Alloy ◽

Precipitate Morphology ◽

Continuous Precipitation ◽

Nickel Base ◽

Base Superalloy ◽

Strengthening Precipitate

A nickel-base superalloy is essentially a Ni/Cr solid solution hardened by additions of Al (Ti, Nb, etc.) to precipitate a coherent, ordered phase. In most commercial alloy systems, e.g. B-1900, IN-100 and Mar-M200, the stable precipitate is Ni3 (Al,Ti) γ′, with an LI2structure. In A lloy 901 the normal precipitate is metastable Nis Ti3 γ′ ; the stable phase is a hexagonal Do2 4 structure. In Alloy 718 the strengthening precipitate is metastable γ″, which has a body-centered tetragonal D022 structure.Precipitate MorphologyIn most systems the ordered γ′ phase forms by a continuous precipitation re-action, which gives rise to a uniform intragranular dispersion of precipitate particles. For zero γ/γ′ misfit, the γ′ precipitates assume a spheroidal.

Download Full-text

The Use of Advanced Analytical Techniques for Characterization of the Chemical, Physical, and Crystallographic Nature of a Surface

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100071107 ◽

1973 ◽

Vol 31 ◽

pp. 132-133 ◽

Cited By ~ 1

Author(s):

R. E. Herfert

Keyword(s):

Surface Characterization ◽

Analytical Techniques ◽

X Ray Diffraction ◽

Depth Of Penetration ◽

X Ray ◽

The Past ◽

Transmission Electron ◽

Scanning Electron

Studies of the nature of a surface, either metallic or nonmetallic, in the past, have been limited to the instrumentation available for these measurements. In the past, optical microscopy, replica transmission electron microscopy, electron or X-ray diffraction and optical or X-ray spectroscopy have provided the means of surface characterization. Actually, some of these techniques are not purely surface; the depth of penetration may be a few thousands of an inch. Within the last five years, instrumentation has been made available which now makes it practical for use to study the outer few 100A of layers and characterize it completely from a chemical, physical, and crystallographic standpoint. The scanning electron microscope (SEM) provides a means of viewing the surface of a material in situ to magnifications as high as 250,000X.

Download Full-text