Achieving ultra-high coefficient of performance of two-phase microchannel heat sink with uniform void fraction

2021 ◽  
pp. 122300
Author(s):  
Xingchi Jiang ◽  
Shiwei Zhang ◽  
Yuanjie Li ◽  
Zuankai Wang ◽  
Chin Pan
Keyword(s):  
Void Fraction ◽  
Heat Sink ◽  
Coefficient Of Performance ◽  
Microchannel Heat Sink ◽  
Two Phase ◽  
High Coefficient

Two-Phase Flow in Microchannels

2001 ◽  
Author(s):  
G. Hetsroni ◽  
A. Mosyak ◽  
Z. Segal
Keyword(s):  
Heat Sink ◽  
High Speed ◽  
Single Phase ◽  
Flow Boiling ◽  
Electronics Cooling ◽  
Working Fluid ◽  
Microchannel Heat Sink ◽  
Two Phase ◽  
Infrared Radiometry ◽  
Phase Water

Abstract Experimental investigation of a heat sink for electronics cooling is performed. The objective is to keep the operating temperature at a relatively low level of about 323–333K, while reducing the undesired temperature variation in both the streamwise and transverse directions. The experimental study is based on systematic temperature, flow and pressure measurements, infrared radiometry and high-speed digital video imaging. The heat sink has parallel triangular microchannels with a base of 250μm. According to the objectives of the present study, Vertrel XF is chosen as the working fluid. Experiments on flow boiling of Vertrel XF in the microchannel heat sink are performed to study the effect of mass velocity and vapor quality on the heat transfer, as well as to compare the two-phase results to a single-phase water flow.

Numerical Investigation of Flow Boiling in a Manifold Microchannel Heat Sink With Conjugate Heat Transfer

2019 ◽  
Author(s):  
Zhichuan Sun ◽  
Yang Luo ◽  
Junye Li ◽  
Wei Li ◽  
Jingzhi Zhang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Numerical Investigation ◽  
Heat Sink ◽  
Conjugate Heat Transfer ◽  
Flow Boiling ◽  
High Heat Flux ◽  
Microchannel Heat Sink ◽  
Two Phase ◽  
Boiling Process ◽  
Manifold Microchannel

Abstract The manifold microchannel heat sink receives an increasing number of attention lately due to its high heat flux dissipation. Numerical investigation of boiling phenomena in manifold microchannel (MMC) heat sinks remains a challenge due to the complexity of fluid route and the limitation of numerical accuracy. In this study, a computational fluid dynamics (CFD) approach including subcooled two-phase flow boiling process and conjugate heat transfer effect is performed using a MMC unit cell model. Different from steady-state single phase prediction in MMC heat sink, this type of modeling allows for the transient simulation for two-phase interface evolution during the boiling process. A validation case is conducted to validate the heat transfer phenomenon among three phases. Besides, this model is used for the assessment of the manifold dimensions in terms of inlet and outlet widths at the mass flux of 1300 kg/m2·s. With different ratios of inlet-to-outlet area, the thermal resistances remain nearly stable.

scholarly journals Thermal Resistance and Pressure Drop Minimization for a Micro-gap Heat Sink with Internal Micro-fins by Parametric Optimization of Operating Conditions

CFD Letters ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 100-112
Author(s):  
Shugata Ahmed ◽  
Erwin Sulaeman ◽  
Ahmad Faris Ismail ◽  
Muhammad Hasibul Hasan ◽  
Zahir Hanouf
Keyword(s):  
Heat Flux ◽  
Pressure Drop ◽  
Thermal Resistance ◽  
Void Fraction ◽  
Heat Sink ◽  
Operating Conditions ◽  
Superior Performance ◽  
Pumping Power ◽  
Two Phase ◽  
Total Thermal Resistance

In recent years, researchers are investigating several potential applications of two-phase flow in micro-gap heat sinks; electronic cooling is one of them. Further, internal micro-fins are used to enhance the heat transfer rate. However, the pressure drop penalty due to small gap height and fin surfaces is a major concern. Hence, minimization of thermal resistance and pressure drop is required. In this paper, effects of operating conditions, e.g., wall heat flux, pumping power, and inlet void fraction, on total thermal resistance and pressure drop in a micro-gap heat sink with internal micro-fins of rectangular and triangular profiles have been investigated by numerical analysis for the R-134a coolant. Furthermore, optimization of these parameters has been carried out by response surface methodology. Simulation results show that rectangular micro-fins show superior performance compared to triangular fins in reducing thermal resistance. Finally, for an optimum condition (7.1202×10-5 W pumping power, 1.2×107 Wm-2 heat flux, and 0.03 inlet void fraction), thermal resistance and pressure drop are reduced by 56.3% and 87.2%, respectively.

Two-Phase Performance of a Hybrid Jet Plus Multipass Microchannel Heat Sink

2019 ◽  
Vol 12 (1) ◽  
Author(s):  
Shailesh N. Joshi ◽  
Danny J. Lohan ◽  
Ercan M. Dede
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Rate ◽  
Heat Sink ◽  
Maximum Pressure ◽  
Microchannel Heat Sink ◽  
Large Area ◽  
Two Phase ◽  
Maximum Heat ◽  
Flow Rates

Abstract The heat transfer and fluid flow performance of a hybrid jet plus multipass microchannel heat sink in two-phase operation is evaluated for the cooling of a single large area, 3.61 cm2, heat source. The two-layer branching microchannel heat sink is evaluated using HFE-7100 as the coolant at three inlet volumetric flow rates of 150, 300, and 450 ml/min. The boiling performance is highest for the flow rate of 450 ml/min with the maximum heat flux value of 174 W/cm2. Critical heat flux (CHF) was observed at two of the tested flow rates, 150 and 300 ml/min, before reaching the maximum operating temperature for the serpentine heater. At 450 ml/min, the heater reached the maximum allowable temperature prior to observing CHF. The maximum pressure drop for the heat sink is 34.1 kPa at a heat flux of 164 W/cm2. Further, the peak heat transfer coefficient value of the heat sink is 28,700 W/m2 K at a heat flux value of 174 W/cm2 and a flow rate of 450 ml/min. Finally, a validated correlation of the single device cooler is presented that predicts heat transfer performance and can be utilized in the design of multidevice coolers.

Sign in / Sign up

Export Citation Format

Share Document