Characterizing thermal damage of diorite treated by an open-ended microwave antenna

Author(s):  
Zhongjun Ma ◽  
Yanlong Zheng ◽  
Jianchun Li ◽  
Xiaobao Zhao ◽  
Qinhua Zhao ◽  
...  
Author(s):  
Karl Schulmeister ◽  
Bernhard Seiser ◽  
Florian Edthofer ◽  
David J. Lund

2014 ◽  
Vol 1038 ◽  
pp. 75-81
Author(s):  
Bernd Niese ◽  
Philipp Amend ◽  
Uwe Urmoneit ◽  
Stephan Roth ◽  
Michael Schmidt

Embedding stereolithography (eSLA) is an additive, hybrid process, which provides a flexible production of 3D components and the ability to integrate electrical and optical conductive structures and functional components within parts. However, the embedding of conductive circuits in stereolithography (SLA) parts assumes usage of process technologies, which enables their direct integration of conductive circuits during the layer-wise building process. In this context, a promising method for in-situ generation of conductive circuits is dispensing of conductive adhesive on the current surface of the SLA part and its subsequent sintering. In this paper, the laser sintering (λ = 355 nm) of conductive adhesive mainly consisting of silver nanoparticles is investigated. The work intends to evaluate the curing behavior of the conductive adhesive, the beam-matter-interactions and the thermal damage of the SLA substrate. The investigations revealed a fast and flexible laser sintering process for the generation of conductive circuits with sufficient electrical conductivity and sufficient current capacity load. In this context, a characterization of the conductive structures is done by measuring their electrical resistance and their potential current capacity load.


2021 ◽  
Vol 288 ◽  
pp. 123100
Author(s):  
Shanbin Xue ◽  
Peng Zhang ◽  
Junjie Wang ◽  
Jiuwen Bao ◽  
Songbai Han ◽  
...  

Author(s):  
Roberto Rheingantz da Cunha Filho ◽  
Lucas José Quioca ◽  
Graziela Junges Crescente Rastelli ◽  
José Fillus Neto
Keyword(s):  

2020 ◽  
Vol 102 (21) ◽  
Author(s):  
Yoichi Shiota ◽  
Ryusuke Hisatomi ◽  
Takahiro Moriyama ◽  
Teruo Ono

Micromachines ◽  
2021 ◽  
Vol 12 (3) ◽  
pp. 289
Author(s):  
Petr Hauschwitz ◽  
Jan Brajer ◽  
Danijela Rostohar ◽  
Jaromír Kopeček ◽  
Tomáš Mocek ◽  
...  

Reflectivity and surface topography of tempered glass were modified without any thermal damage to the surroundings by utilizing 1.7 ps ultrashort pulsed laser on its fundamental wavelength of 1030 nm. To speed up the fabrication, a dynamic beam shaping unit combined with a galvanometer scanning head was applied to divide the initial laser beam into a matrix of beamlets with adjustable beamlets number and separation distance. By tuning the laser and processing parameters, reflected intensity can be reduced up to 75% while maintaining 90% of transparency thus showing great potential for display functionalization of mobile phones or laptops.


Sensors ◽  
2021 ◽  
Vol 21 (2) ◽  
pp. 643
Author(s):  
Martina De Landro ◽  
Ignacio Espíritu García-Molina ◽  
Manuel Barberio ◽  
Eric Felli ◽  
Vincent Agnus ◽  
...  

This work presents the potential of hyperspectral imaging (HSI) to monitor the thermal outcome of laser ablation therapy used for minimally invasive tumor removal. Our main goal is the establishment of indicators of the thermal damage of living tissues, which can be used to assess the effect of the procedure. These indicators rely on the spectral variation of temperature-dependent tissue chromophores, i.e., oxyhemoglobin, deoxyhemoglobin, methemoglobin, and water. Laser treatment was performed at specific temperature thresholds (from 60 to 110 °C) on in-vivo animal liver and was assessed with a hyperspectral camera (500–995 nm) during and after the treatment. The indicators were extracted from the hyperspectral images after the following processing steps: the breathing motion compensation and the spectral and spatial filtering, the selection of spectral bands corresponding to specific tissue chromophores, and the analysis of the areas under the curves for each spectral band. Results show that properly combining spectral information related to deoxyhemoglobin, methemoglobin, lipids, and water allows for the segmenting of different zones of the laser-induced thermal damage. This preliminary investigation provides indicators for describing the thermal state of the liver, which can be employed in the future as clinical endpoints of the procedure outcome.


Author(s):  
Sundar Marimuthu ◽  
Bethan Smith

This manuscript discusses the experimental results on 300 W picosecond laser machining of aerospace-grade nickel superalloy. The effect of the laser’s energetic and beam scanning parameters on the machining performance has been studied in detail. The machining performance has been investigated in terms of surface roughness, sub-surface thermal damage, and material removal rate. At optimal process conditions, a picosecond laser with an average power output of 300 W can be used to achieve a material removal rate (MRR) of ∼140 mm3/min, with thermal damage less than 20 µm. Shorter laser pulse widths increase the material removal rate and reduce the resultant surface roughness. High scanning speeds improve the picosecond laser machining performance. Edge wall taper of ∼10° was observed over all the picosecond laser machined slots. The investigation demonstrates that high-power picosecond lasers can be used for the macro-machining of industrial components at an acceptable speed and quality.


Sign in / Sign up

Export Citation Format

Share Document