A rational formula to predict punching shear capacity at interior columns connections with RC flat slabs reinforced with either steel or FRP bars but without shear reinforcement

Structures ◽  
2022 ◽  
Vol 37 ◽  
pp. 56-68
Author(s):  
Thaer M. Saeed Alrudaini
Keyword(s):  
Shear Capacity ◽  
Punching Shear ◽  
Shear Reinforcement ◽  
Flat Slabs ◽  
Frp Bars

scholarly journals PERILAKU PUNCHING SHEAR PADA HUBUNGAN KOLOM BULAT DENGAN FLAT SLAB AKIBAT BEBAN TEKAN AKSIAL

2019 ◽  
Vol 1 (1) ◽  
pp. 1-14
Author(s):  
Muhammad Zardi
Keyword(s):  
Concrete Strength ◽  
Load Condition ◽  
Maximum Load ◽  
Shear Capacity ◽  
Punching Shear ◽  
Shear Reinforcement ◽  
Eccentric Load ◽  
Flat Slab ◽  
Circular Column ◽  
Flat Slabs

The aim of the tests was to investigate the influence of concrete strength, the eccentricity of the column and the use of shear reinforcement in flat slabs on punching shear. The research specimens are 8 units of flat slabs. Flat slab size 1400 x 1400 mm2 with thickness of 120 mm. Flat slabs were connected with circular column with dimension 225 mm  of diameter and 200 mm of height. Flat slabs were made in to 2 variations of concrete strength, e.i. 30 MPa and 60 MPa, 2 variations of shear reinforcement, e.i. without shear reinforcement and with shear reinforcement and 2 variations of eccentricity that, e.i. without eccentricity and with eccentricity. Each treatment has 1 specimen. Each specimen has 6 cylinder specimens. Cylinder specimens used as a concrete strength control for main specimen (flat slab). The tests showed that the concrete strength had a strong influence on punching shear strength. This is shown by capacity increase of 42.78%; 54.00%; 46.59% and 0.02%. The value is ratio between the maximum load of the specimens with 60 MPa and 30 MPa at the same eccentricity and the same shear reinforcement. The eccentricity of column reduce the capacity of punching shear. This is shown by 3 specimens decrease in capacity of 3.70%; 36.75% and 7.30%. Only 1 specimen that increase in capacity of 9.27%. The value is ratio between the maximum load of the specimens with 40 mm eccentricity and 0 mm eccentricity at the same compressive strenght and the same shear reinforcement. The use of shear reinforcement does not always increase the punching shear capacity. There are 2 observations that increased capacity (52.07% and 65.37% at the centric load) and 2 observations decreased capacity (0.12% and 4.92% at the eccentric load). The value is ratio between the maximum load on the specimens using shear reinforcement with the specimens that do not use shear reinforcement at the same compressive strenght and the same eccentricity.The use of shear reinforcement increase punching shear capacity of flat slab at the centric load condition. The use of shear reinforcement decrease punching shear capacity of flat slab at the eccentric load condition.

scholarly journals New Methods to Resisting Punching Shear Stress in Reinforced Concrete Flat Slabs

2018 ◽  
Vol 8 (02) ◽  
Author(s):  
Fatma M. Eid ◽  
Tayel Magdy ◽  
Ebada Ahmed
Keyword(s):  
Reinforced Concrete ◽  
Shear Failure ◽  
Shear Capacity ◽  
Punching Shear ◽  
Shear Reinforcement ◽  
Reinforcement System ◽  
Strength Concrete ◽  
Flat Slabs ◽  
The Difference ◽  
Compact Strength

Punching shear failure is a major problem encountered in the design of reinforced concrete flat slabs. The utilization of shear reinforcement via shear studs or other means has become a choice for improving the punching shear capacity. In this study, a new alternative of reinforcement modalities were tested and demonstrated the effect of self-compact concrete on the punching shear capacity, beside that compared between the difference codes to identify the suitable one for determining the position of critical section of punching shear. Nevertheless, in this investigation, the proposed reinforcement system is examined for interior columns only. An experimental work consisting of six specimens: five of them were cast with normal reinforced concrete and one was cast with self-compact strength concrete. The obtained results indicate that the proposed shear reinforcement system has a positive effect in the enhancement of the punching shear capacity of interior slab–column connection of self-compact strength concrete.

scholarly journals Theoretical prediction of punching shear capacity of flat slabs without shear reinforcement strengthened by concrete topping

2021 ◽  
Vol 1203 (2) ◽  
pp. 022108
Author(s):  
Daniel Čereš ◽  
Katarína Gajdošová
Keyword(s):  
Shear Resistance ◽  
Design Guidelines ◽  
Shear Capacity ◽  
Reinforcement Ratio ◽  
Punching Shear ◽  
Shear Reinforcement ◽  
Model Code ◽  
Flat Slabs ◽  
Eurocode 2 ◽  
Model Code 2010

Abstract The main reasons for strengthening flat slabs are the change of the use of a building, increase in the value of loads, degradation of the concrete cover layer, or insufficient reinforcement. This paper is focused on the assessment of punching shear capacity of the strengthened flat slabs without shear reinforcement. One of the possibilities how to enhance punching shear capacity is the addition of reinforced concrete topping. The main goal of this paper is to compare the possibilities for calculation of the increase in the punching shear capacity by investigation of the influence of different thicknesses of concrete toppings and different reinforcement ratio. A reference specimen is represented by a fragment of a flat slab with the thickness of h = 200 mm supported by circular column with the diameter of 250 mm. Three different thicknesses (50 mm, 100 mm, 150 mm) of concrete toppings were considered together with three different reinforcement ratios for each thickness of concrete overlay. Theoretical predictions of the punching shear resistance of flat slabs were evaluated by design guidelines according to the relevant standards: Eurocode 2 (EN 1992-1-1), Model Code 2010 and draft of the second generation of Eurocode 2 (prEN 1992-1-1). The differences in the influence of reinforcement ratio are significant. In Model Code 2010 the reinforcement ratio in concrete topping was considered in equation of moment of resistance. This is unlike in both of the mentioned Eurocodes, where the reinforcement ratio was assumed as a geometric average value of the original reinforcement ratio in the slab before strengthening and of the reinforcement ratio of concrete topping. All the predicted theoretical calculations are based on the perfect connection and bond between the original and new layer of concrete. These predictions should be verified by experimental investigation, which is going to be prepared shortly. By the additional increase in the thickness of concrete topping or in the amount of added reinforcement the attention should be payed to the limitation of the punching shear resistance by the value of the maximum punching shear resistance in the compression concrete strut.

scholarly journals Performance of Shear Reinforcement against Punching Shear Loads

2019 ◽  
Vol 9 (2) ◽  
pp. 841-850
Keyword(s):  
Numerical Study ◽  
Shear Capacity ◽  
Punching Shear ◽  
Slab Thickness ◽  
Test Results ◽  
Shear Reinforcement ◽  
Concentrated Load ◽  
Flat Slab ◽  
Flat Slabs ◽  
Strength Formula

This research targets to maximize the ductility and strength of the reinforced concrete flat slabs. However, to be efficient, the shear reinforcement must be anchored well in the tension and compression zones of the slab. The test results on the slab-column connection models which provided with shear reinforcement are introduced in this study. The benefits of using shear reinforcement are to reduce the slab thickness, and to minimize both the cost and the total weight of the structure. Twelve flat slab specimens have been tested to study the effect of different types of steel RFT on the punching shear of the flat slab. The experimental parameters include no shear reinforcement which study the advantage of using tension RFT ONLY against punching shear, no shear reinforcement which study the advantage of using compression RFT against punching shear, shear RFT (Vertical Stirrups) which study the effect of using shear RFT with constant distribution 0.5d, and a new distribution of shear stirrups which study the effect of using new different width & spacing of vertical stirrups. The twelve specimens were loaded with concentrated load at the mid span until failure. The general behavior of the deformation of the tested slab specimens was examined and recorded (cracking, deflection, and strain in both steel and concrete). A comparison established between the experimental and the numericaltheoretical results obtained from applying the punching shear strength formula given in design codes, and finite element modeling analysis; ABAQUS 2017 software package was used for this analysis. A total of six building codes were examined with regard to their provisions concerning the punching shear. A comparison had been made between the research test results and the codes equations to improve the methods of the analysis about the flat slabs. This study aimed to improve the punching shear capacity of flat slab which leads to more accurate results compared with the codes predictions. To achieve this aim, an experimental and numerical study was carried out for this investigation.

Activation model for various punching shear reinforcement types in flat slabs and column bases optimized for design

2021 ◽  
Vol 249 ◽  
pp. 113310
Author(s):  
Philipp Schmidt ◽  
Michel Pleim ◽  
Jan Bielak ◽  
Josef Hegger
Keyword(s):  
Punching Shear ◽  
Shear Reinforcement ◽  
Activation Model ◽  
Flat Slabs ◽  
Column Bases

Numerische Untersuchungen zur Durchstanztragfähigkeit von Flachdeckensystemen/Numerical investigations on punching shear capacity of continuous flat slabs

Bauingenieur ◽  
2018 ◽  
Vol 93 (04) ◽  
pp. 141-151
Author(s):  
D. Kueres ◽  
P. Schmidt ◽  
S. Bosbach ◽  
M. Classen ◽  
M. Herbrand ◽  
...  
Keyword(s):  
Shear Capacity ◽  
Punching Shear ◽  
Numerical Investigations ◽  
Flat Slabs ◽  
Finite Elemente

Das Durchstanztragverhalten von Stahlbetonplatten wird seit mehreren Jahrzehnten experimentell erforscht. Aufgrund des hohen Kosten- und Arbeitsaufwandes von Durchstanzversuchen an Flachdeckensystemen wurde der Großteil der vorhandenen Durchstanzversuche an isolierten Flachdeckenausschnitten durchgeführt. Die Geometrie der Versuchskörper wurde dabei mit dem Ziel gewählt, den Stützmomentbereich um die jeweils betrachtete Decke-Stütze-Verbindung zu simulieren. Günstige Einflüsse, die sich in Flachdeckensystemen zum Beispiel aus Momentenumlagerungen oder Druckmembrantragwirkung ergeben, können in diesen Versuchen nicht auftreten. Daher eignen sich die vorhandenen Versuche in erster Linie zur sicheren Abschätzung der Durchstanztragfähigkeit.   Aufbauend auf theoretischen und experimentellen Untersuchungen aus der Literatur, wird in diesem Beitrag die Durchstanztragfähigkeit von Flachdeckensystemen anhand von nicht-linearen Finite-Elemente-Simulationen genauer untersucht. Das verwendete numerische Modell wird zunächst anhand von Durchstanzversuchen validiert. Nachfolgend wird das Modell für weiterführende Parameterstudien verwendet, um die Unterschiede zwischen Flachdeckensystemen und –ausschnitten genauer zu analysieren. Die Ergebnisse der numerischen Untersuchungen werden abschließend dafür genutzt, einen praxistauglichen Ansatz zur Bestimmung der Durchstanztragfähigkeit von Flachdeckensystemen im Bereich von Innenstützen abzuleiten.

Punching shear behaviour of flat slabs with different reinforcement schemes: openings and rectangularity effects

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Donia Salman ◽  
Rabab Allouzi ◽  
Nasim Shatarat
Keyword(s):  
Structural Engineering ◽  
Experimental Tests ◽  
Shear Capacity ◽  
Punching Shear ◽  
Shear Behaviour ◽  
Cross Sectional ◽  
Content Type ◽  
Flat Slabs ◽  
Reinforced Concrete Slabs ◽  
Rectangular Columns

PurposeThe main goal is to investigate the effect of size and location of opening and column size on the punching shear strength. Openings are often needed in order to install mechanical and electrical services. This process takes away part of the concrete volume which is responsible for resisting the shear forces and any unbalanced moment. Furthermore, the application of rectangular columns in flat slabs is commonly used in practice as they provide lateral stiffness to the building. They are also utilised in garages and multi-storey buildings where these elongated cross-sectional columns reduce the effective span length between adjacent columns.Design/methodology/approachThis research is a numerical-based investigation that is calibrated based on a thirteen previously tested and numerically calibrated slab specimens with no openings. A parametric study is conducted in this study to consider the effect of other parameters, which are the size and location of opening and the rectangularity ratio of column in order to evaluate their effect on the punching shear capacity. A total of 156 models are developed to study these factors. Additionally, the predicted shear carrying capacity of the simulated slabs is calculated using the ACI318–19 and Eurocode (EC2-04) equation.FindingsThe presence of openings reduced the punching shear capacity. The small opening's location and orientation have almost no effect except for one slab. For slabs of large openings, the presence of openings reduced the punching capacity. The punching capacity is higher when the openings are farther from the column. The numerically obtained results of slabs with rectangular columns show lower punching capacity compared to slabs of squared columns with the same length of the punching shear control perimeter. The punching capacity for all slabs is predicted by ACI318–19 and Eurocode (EC2-04) and it is found that Eurocode (EC2-04) provided a closer estimation.Originality/valueThe slabs considered for calibration were reinforced with four different punching shear reinforcement configurations, namely; ordinary closed rectangular stirrups, rectangular spiral stirrups, advanced rectangular spiral stirrups and circular spiral. Generally, there has been limited research on concrete flat slabs with openings in comparison with other subjects related to structural engineering (Guan, 2009) and no research on punching shear with openings of slabs reinforced with these reinforcement schemes. The available research focussed on the effects of openings on the flexural behaviour of reinforced concrete slabs includes Casadei et al. (2003), Banu et al. (2012) and Elsayed et al. (2009). In addition, experimental tests that examined slabs supported on rectangular columns are very limited.

Punching shear behavior of reinforced concrete flat slabs with a varying amount of shear reinforcement

2019 ◽  
Vol 21 (1) ◽  
pp. 235-246 ◽  
Author(s):  
Philipp Schmidt ◽  
Dominik Kueres ◽  
Josef Hegger
Keyword(s):  
Reinforced Concrete ◽  
Shear Behavior ◽  
Punching Shear ◽  
Shear Reinforcement ◽  
Flat Slabs

scholarly journals A Novel Feature Selection Approach Based on Tree Models for Evaluating the Punching Shear Capacity of Steel Fiber-Reinforced Concrete Flat Slabs

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3902 ◽  
Author(s):  
Shasha Lu ◽  
Mohammadreza Koopialipoor ◽  
Panagiotis G. Asteris ◽  
Maziyar Bahri ◽  
Danial Jahed Armaghani
Keyword(s):  
Feature Selection ◽  
Reinforced Concrete ◽  
Predictive Models ◽  
Steel Fiber ◽  
Shear Capacity ◽  
Fiber Reinforced Concrete ◽  
Punching Shear ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Flat Slabs

When designing flat slabs made of steel fiber-reinforced concrete (SFRC), it is very important to predict their punching shear capacity accurately. The use of machine learning seems to be a great way to improve the accuracy of empirical equations currently used in this field. Accordingly, this study utilized tree predictive models (i.e., random forest (RF), random tree (RT), and classification and regression trees (CART)) as well as a novel feature selection (FS) technique to introduce a new model capable of estimating the punching shear capacity of the SFRC flat slabs. Furthermore, to automatically create the structure of the predictive models, the current study employed a sequential algorithm of the FS model. In order to perform the training stage for the proposed models, a dataset consisting of 140 samples with six influential components (i.e., the depth of the slab, the effective depth of the slab, the length of the column, the compressive strength of the concrete, the reinforcement ratio, and the fiber volume) were collected from the relevant literature. Afterward, the sequential FS models were trained and verified using the above-mentioned database. To evaluate the accuracy of the proposed models for both testing and training datasets, various statistical indices, including the coefficient of determination (R2) and root mean square error (RMSE), were utilized. The results obtained from the experiments indicated that the FS-RT model outperformed FS-RF and FS-CART models in terms of prediction accuracy. The range of R2 and RMSE values were obtained as 0.9476–0.9831 and 14.4965–24.9310, respectively; in this regard, the FS-RT hybrid technique demonstrated the best performance. It was concluded that the three hybrid techniques proposed in this paper, i.e., FS-RT, FS-RF, and FS-CART, could be applied to predicting SFRC flat slabs.

Sign in / Sign up

Export Citation Format

Share Document