Robustness of steel moment frames in multi-column-removal scenarios

2020 ◽  
Vol 175 ◽  
pp. 106325
Author(s):  
Jing-Zhou Zhang ◽  
Bin-Hui Jiang ◽  
Ran Feng ◽  
Rui Chen
Keyword(s):  
Moment Frames ◽  
Steel Moment Frames ◽  
Column Removal

Performance of Precast Concrete Moment Frames Subjected to Column Removal: Part 1, Experimental Study

PCI Journal ◽  
2017 ◽  
Vol 62 (5) ◽  
Author(s):  
H. S. Lew ◽  
Joseph A. Main ◽  
Yihai Bao ◽  
Fahim Sadek ◽  
Vincent P. Chiarito ◽  
...  
Keyword(s):  
Experimental Study ◽  
Precast Concrete ◽  
Moment Frames ◽  
Column Removal

Effects of Fling Step and Forward Directivity on Seismic Response of Buildings

2006 ◽  
Vol 22 (2) ◽  
pp. 367-390 ◽  
Author(s):  
Erol Kalkan ◽  
Sashi K. Kunnath
Keyword(s):  
Seismic Response ◽  
Ground Motions ◽  
High Amplitude ◽  
Moment Frames ◽  
Steel Moment Frames ◽  
Damage Potential ◽  
Near Fault ◽  
Forward Directivity ◽  
Fling Step ◽  
Far Fault

This paper investigates the consequences of well-known characteristics of near-fault ground motions on the seismic response of steel moment frames. Additionally, idealized pulses are utilized in a separate study to gain further insight into the effects of high-amplitude pulses on structural demands. Simple input pulses were also synthesized to simulate artificial fling-step effects in ground motions originally having forward directivity. Findings from the study reveal that median maximum demands and the dispersion in the peak values were higher for near-fault records than far-fault motions. The arrival of the velocity pulse in a near-fault record causes the structure to dissipate considerable input energy in relatively few plastic cycles, whereas cumulative effects from increased cyclic demands are more pronounced in far-fault records. For pulse-type input, the maximum demand is a function of the ratio of the pulse period to the fundamental period of the structure. Records with fling effects were found to excite systems primarily in their fundamental mode while waveforms with forward directivity in the absence of fling caused higher modes to be activated. It is concluded that the acceleration and velocity spectra, when examined collectively, can be utilized to reasonably assess the damage potential of near-fault records.

Column Moment Demands from Orthogonal Beam Twisting

2018 ◽  
Vol 763 ◽  
pp. 259-269
Author(s):  
George Webb ◽  
Kanyakon Kosinanonth ◽  
Tushar Chaudhari ◽  
Saeid Alizadeh ◽  
Gregory A. MacRae
Keyword(s):  
Lateral Displacement ◽  
Frame Structure ◽  
Moment Frames ◽  
Steel Moment Frames ◽  
Element Analysis ◽  
Soft Storey ◽  
Simply Supported ◽  
Composite Frame ◽  
Explicit Consideration ◽  
Column Joint

Beam column joint subassemblies in steel moment frames often have simply-supported gravity beams framing into the joint in the perpendicular direction. When these subassemblies undergo lateral displacement, moments enter the column from the beams. Some of these moments are directly applied from the in-plane beam and slab stresses as they contact the column, and additional moments occur as the slab causes the perpendicular simply supported beams to twist. In most design codes around the world, no explicit consideration of these moments is performed even though they may increase the likelihood of column yielding and a soft-storey mechanism. This paper quantifies the magnitude of these perpendicular beam twisting moments in typical subassemblies using inelastic finite element analysis. It is shown that for beam-column-joint-slab subassemblies where the primary and secondary beams are fully welded to the column, the addition of slab effects significantly increases the total stiffness and strength of the composite frame structure. In addition to this, it is also shown the twisting moment demand of the secondary beams increased the frames strength by approximately 2% for an imposed drift of 5% for the subassembly investigated when no gap was provided between slab and the column. It was also shown the twisting moment demand of the secondary beams increased the frames strength by approximately 10% for a maximum imposed drift of 5% for the subassembly investigated when a gap was provided between the slab and the column.

Numerical Analysis of Collapse Behavior for Steel Moment Frames

2015 ◽  
Vol 104 (1) ◽  
pp. 1-8
Author(s):  
Seiji Mukaide ◽  
Motohide Tada
Keyword(s):  
Numerical Analysis ◽  
Moment Frames ◽  
Steel Moment Frames ◽  
Collapse Behavior
Sign in / Sign up

Export Citation Format

Share Document