Column Moment Demands from Orthogonal Beam Twisting

2018 ◽  
Vol 763 ◽  
pp. 259-269
Author(s):  
George Webb ◽  
Kanyakon Kosinanonth ◽  
Tushar Chaudhari ◽  
Saeid Alizadeh ◽  
Gregory A. MacRae
Keyword(s):  
Lateral Displacement ◽  
Frame Structure ◽  
Moment Frames ◽  
Steel Moment Frames ◽  
Element Analysis ◽  
Soft Storey ◽  
Simply Supported ◽  
Composite Frame ◽  
Explicit Consideration ◽  
Column Joint

Beam column joint subassemblies in steel moment frames often have simply-supported gravity beams framing into the joint in the perpendicular direction. When these subassemblies undergo lateral displacement, moments enter the column from the beams. Some of these moments are directly applied from the in-plane beam and slab stresses as they contact the column, and additional moments occur as the slab causes the perpendicular simply supported beams to twist. In most design codes around the world, no explicit consideration of these moments is performed even though they may increase the likelihood of column yielding and a soft-storey mechanism. This paper quantifies the magnitude of these perpendicular beam twisting moments in typical subassemblies using inelastic finite element analysis. It is shown that for beam-column-joint-slab subassemblies where the primary and secondary beams are fully welded to the column, the addition of slab effects significantly increases the total stiffness and strength of the composite frame structure. In addition to this, it is also shown the twisting moment demand of the secondary beams increased the frames strength by approximately 2% for an imposed drift of 5% for the subassembly investigated when no gap was provided between slab and the column. It was also shown the twisting moment demand of the secondary beams increased the frames strength by approximately 10% for a maximum imposed drift of 5% for the subassembly investigated when a gap was provided between the slab and the column.

Effect of fully restrained beam-to-column connection on the progressive collapse strength of steel moment frames

2020 ◽  
Vol 23 (8) ◽  
pp. 1656-1668
Author(s):  
Alireza Salmasi ◽  
Mohammad Reza Sheidaii ◽  
Mohammad Saghaie Sahebalzaman ◽  
Saeed Tariverdilo
Keyword(s):  
Structural Integrity ◽  
Progressive Collapse ◽  
Nonlinear Effects ◽  
Frame Structure ◽  
Moment Frames ◽  
Steel Moment Frames ◽  
Plastic Hinges ◽  
Dynamic Increase Factor ◽  
Collapse Strength ◽  
Alternate Path Method

The beam-to-column connection has been identified as a key element for steel frame structures to maintain the structural integrity during progressive collapse phenomenon. In the current study, in order to assess the effects of beam-to-column connection type on the progressive collapse strength of steel moment frames, the progressive collapse behavior of a steel intermediate moment frame structure was evaluated with 10 different types of fully restrained connections. The progressive collapse strength of these buildings against sudden removal of a column was separately studied using nonlinear static alternate path method presented in Unified Facility Criteria progressive collapse guideline. To consider the nonlinear effects in the structural modeling, plastic hinges for beam and column members and connections were defined and modeled according to the ASCE 41 standard. The results of the progressive collapse analyses indicated that if the plastic hinges of connections are separately defined in addition to the plastic hinges of beams and columns, the structure will have lower progressive collapse strength, and the calculated dynamic increase factor will grow. Among the studied types of connections, the free flange connection had the best performance and the highest strength against progressive collapse.

Hysteresis Behavior of Square Tube Columns to H-Beam Connections with Vertical Stiffeners

2005 ◽  
Vol 8 (6) ◽  
pp. 561-572 ◽  
Author(s):  
Jinan Chung ◽  
Seongyon Seo ◽  
Chiaki Matsui ◽  
Sungmo Choi
Keyword(s):  
Test Methods ◽  
Test Results ◽  
Moment Frames ◽  
Steel Moment Frames ◽  
Steel Moment Resisting Frames ◽  
Simply Supported ◽  
Moment Resisting Frames ◽  
Connection Method ◽  
Moment Resisting ◽  
H Beam

This paper deals with confirming the usability of a new connection method for steel moment-resisting frames. The connections are strengthened with vertical stiffeners to connect square tube columns and H-shaped beams. Two test methods were selected with experimental parameters given as details. The first test is performed under symmetrical loading. Beams are simply supported on both ends and test load is applied to the top of the column. The second test is performed under anti-symmetric loading. The shape of test specimens is cruciform, with a beam and a column. The top end and base of the column are simply supported, and load is applied to both ends of the beam. Test results are summarized to investigate structural performances of the connection. Nonlinear FE analysis using ANSYS for moment-resisting frames was performed to confirm the test results. It was found that all specimens had sufficient capacities exceeding the full plastic strength of beam. Therefore, the connections strengthened with vertical stiffeners were successfully verified to have possibility as a new connection method for steel moment-frames.

Effects of Fling Step and Forward Directivity on Seismic Response of Buildings

2006 ◽  
Vol 22 (2) ◽  
pp. 367-390 ◽  
Author(s):  
Erol Kalkan ◽  
Sashi K. Kunnath
Keyword(s):  
Seismic Response ◽  
Ground Motions ◽  
High Amplitude ◽  
Moment Frames ◽  
Steel Moment Frames ◽  
Damage Potential ◽  
Near Fault ◽  
Forward Directivity ◽  
Fling Step ◽  
Far Fault

This paper investigates the consequences of well-known characteristics of near-fault ground motions on the seismic response of steel moment frames. Additionally, idealized pulses are utilized in a separate study to gain further insight into the effects of high-amplitude pulses on structural demands. Simple input pulses were also synthesized to simulate artificial fling-step effects in ground motions originally having forward directivity. Findings from the study reveal that median maximum demands and the dispersion in the peak values were higher for near-fault records than far-fault motions. The arrival of the velocity pulse in a near-fault record causes the structure to dissipate considerable input energy in relatively few plastic cycles, whereas cumulative effects from increased cyclic demands are more pronounced in far-fault records. For pulse-type input, the maximum demand is a function of the ratio of the pulse period to the fundamental period of the structure. Records with fling effects were found to excite systems primarily in their fundamental mode while waveforms with forward directivity in the absence of fling caused higher modes to be activated. It is concluded that the acceleration and velocity spectra, when examined collectively, can be utilized to reasonably assess the damage potential of near-fault records.

Experimental Research and Finite Element Analysis on Behavior of Steel Frame with Semi-Rigid Connections

2010 ◽  
Vol 168-170 ◽  
pp. 553-558
Author(s):  
Feng Xia Li ◽  
Bu Xin
Keyword(s):  
Architectural Design ◽  
Plastic Hinge ◽  
Steel Frames ◽  
Seismic Energy ◽  
Internal Force ◽  
Steel Frame ◽  
Frame Structure ◽  
Element Analysis ◽  
Rigid Deformation ◽  
Steel Frame Structure

Most steel beam-column connections actually show semi-rigid deformation behavior that can contribute substantially to overall displacements of the structure and to the distribution of member forces. Steel frame structure with semi-rigid connections are becoming more and more popular due to their many advantages such as the better satisfaction with the flexible architectural design, low inclusive cost and environmental protect as well. So it is very necessary that studying the behavior of those steel frame under cyclic reversal loading. On the basics of connections experiments the experiment research on the lateral resistance system of steel frame structure has been completed. Two one-second scale, one-bay, two-story steel frames with semi-rigid connections under cyclic reversal loading. The seismic behavior of the steel frames with semi-rigid connections, including the failure pattern, occurrence order of plastic hinge, hysteretic property and energy dissipation, etc, was investigated in this paper. Some conclusions were obtained that by employing top-mounted and two web angles connections, the higher distortion occurred in the frames, and the internal force distributing of beams and columns was changed, and the ductility and the absorbs seismic energy capability of steel frames can be improved effectively.

ANSYS Simply Supported Deep Beams Based on the Study of Mechanical Properties

2013 ◽  
Vol 351-352 ◽  
pp. 782-785
Author(s):  
Yong Bing Liu ◽  
Xiao Zhong Zhang
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Mechanical Model ◽  
Work Performance ◽  
Deep Beam ◽  
Analysis Software ◽  
Deep Beams ◽  
Element Analysis ◽  
Simply Supported ◽  
Force Characteristics

Established the mechanical model of simply supported deep beam, calculation and analysis of simple supported deep beams by using finite element analysis software ANSYS, simulated the force characteristics and work performance of the deep beam. Provides the reference for the design and construction of deep beams.

Sign in / Sign up

Export Citation Format

Share Document