scholarly journals Horizontal end crack control and load-bearing capacity performance of hollow-type pretensioned girders through experimentally calibrated finite element models

2021 ◽  
Author(s):  
Bashir Ahmad Aasim ◽  
Abdul Khaliq Karimi ◽  
Jun Tomiyama ◽  
Yuya Suda
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Finite Element Models ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Crack Control ◽  
Capacity Performance

Finite Element Analysis of Lightweight Energy-Saving Composite Floor

2014 ◽  
Vol 665 ◽  
pp. 196-202
Author(s):  
Yi Qing Guo ◽  
Ping Zhou Cao
Keyword(s):  
Finite Element ◽  
Elastic Modulus ◽  
Bearing Capacity ◽  
Energy Saving ◽  
Element Model ◽  
Finite Element Models ◽  
Load Bearing Capacity ◽  
Element Analysis ◽  
Load Bearing ◽  
Thin Panel

In order to study the performance of lightweight energy-saving composite floor, the finite element models of composite floor were established, which was based on the composite floor specimens test research. The finite element models were verified rationally and correctly in the paper, through compared with the composite floor test results. The finite element model can be used to analyze the load-bearing capacity of composite floor. Various influencing factors of composite floor with simply supported end were analyzed, such as the span of self-tapping screw, the diameter of self-tapping screw, the strength of thin panel and the elastic modulus of thin panel, etc. The results show that the load-bearing capacity of composite floor increases with the increase of the number of self-tapping screw, the diameter of self-tapping screw, the strength of thin panel and the elastic modulus of thin panel, etc. The load-bearing capacity calculate formula of composite floor was proposed.

Axial behaviour of slender concrete-filled steel tube square columns strengthened with square concrete-filled steel tube jackets

2019 ◽  
Vol 23 (6) ◽  
pp. 1074-1086 ◽  
Author(s):  
Tao Zhu ◽  
Hongjun Liang ◽  
Yiyan Lu ◽  
Weijie Li ◽  
Hong Zhang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Bearing Capacity ◽  
Element Model ◽  
Steel Tube ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Concrete Filled Steel Tube ◽  
Experimental Parameters ◽  
Modified Formula

This article investigates the behaviour of slender concrete-filled steel tube square columns strengthened by concrete-filled steel tube jacketing. The columns were realised by placing a square outer steel tube around the original slender concrete-filled steel tube column and pouring strengthening concrete into the gap between the inner and outer steel tubes. Three concrete-filled steel tube square columns and seven retrofitted columns ranging from 1200 to 2000 mm were tested to failure under axial compression. The experimental parameters included three length-to-width ( L/ B1) ratios, three width-to-thickness ( B1/ t1) ratios and three strengths of concrete jacket (C50-grade, C60-grade and C70-grade). Experimentally, the retrofitted columns failed in a similar manner to traditional slender concrete-filled steel tube columns. After strengthening, the retrofitted columns benefitted greatly from the component materials, with their load-bearing capacity and ductility notably enhanced. These enhancements were mainly brought about by sectional enlargement and good confinement of concrete. A finite element model was developed using ABAQUS to better understand the axial behaviour of the retrofitted specimens. A parametric study was conducted, with parameters including the length of the column, thickness of the outer steel tube, strength of the concrete jacket, yield strength of the outer steel tube, thickness of the inner steel tube and strength of the inner concrete. Furthermore, the finite element model was adopted to study the behaviour of rust-damaged and post-fire slender concrete-filled steel tube square columns strengthened by square concrete-filled steel tube jacketing. A modified formula was proposed to predict the load-bearing capacity of retrofitted specimens, and the numerical results agreed well with the experiments and the finite element results of undamaged, rust-damaged and post-fire specimens. It could be used as a reference for practical application.

scholarly journals PLASTIC CAPACITY OF BOLTED RHS FLANGE-PLATE JOINTS UNDER AXIAL TENSION

2016 ◽  
Vol 8 (3) ◽  
pp. 85-93
Author(s):  
Andrej Mudrov ◽  
Gintas Šaučiuvėnas ◽  
Antanas Sapalas ◽  
Ivar Talvik
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Load Bearing Capacity ◽  
Finite Element Program ◽  
Load Bearing ◽  
Axial Tension ◽  
Flange Thickness ◽  
Element Program ◽  
Two Sides ◽  
Ansys Workbench

This article considers the calculation of load-bearing capacity of flange-plate joints with bolts along two sides of rectangular hollow sections (RHS) under axial tension. It provides a review and comparison of various calculation methodologies for establishing the load-bearing capacity of RHS flange-plate joints, such as suggested in EN 1993-1-8:2005 and STR 2.05.08:2005 as well as those proposed in different countries and by other authors. Common design principles and derived results for load-bearing capacity of flange-plate joints have been analysed and compared. Following the numerical modelling, which has been done using ANSYS Workbench finite element program, the derived results for load-bearing capacity have been compared with analytical load-bearing capacity results for flange-plate joints of the same structure. The analysis has focused on one type of flange-plate joints with bolts – both preloaded and non-preloaded – along two opposite sides of the tube, with the flange thickness of 15 mm and 25 mm.

Research on Deflection Calculation of Laminated Glass Simply Supported on Four Sides

2011 ◽  
Vol 341-342 ◽  
pp. 833-837
Author(s):  
Xun Wang ◽  
Qi Lin Zhang ◽  
Jun Chen ◽  
Zhi Xiong Tao ◽  
Jun Chen
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Correction Coefficient ◽  
Laminated Glass ◽  
Load Bearing Capacity ◽  
Equivalent Thickness ◽  
Curtain Wall ◽  
Load Bearing ◽  
Simply Supported ◽  
Finite Element Software

Combining with load bearing capacity tests, the laminated glass simply supported on four sides subjected to bending is analyzed using the finite element software ANSYS. Based on the theoretical and experimental deflection results, the accurate calculation model is established. In order to calculate the deflection of laminated glass subjected to short-time loading such as wind load based on different codes, the equivalent thickness of laminated glass based on Chinese code 2003 and European code is calculated, respectively. Finally, on the basis of many finite element analyses, load bearing capacity tests and code values, the formulas for calculating maximum deflectiont of four-sides supported laminated glass is revised in “Technical code for glass curtain wall engineering” (China) and corresponding correction coefficient is given.

scholarly journals Method of Calculation Flexural Stiffness Over Natural Oscillations Frequencies

2018 ◽  
Vol 64 (4) ◽  
pp. 89-103
Author(s):  
A. Nesterenko ◽  
G. Stolpovskiy ◽  
M. Nesterenko
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Bearing Capacity ◽  
Flexural Stiffness ◽  
The Finite Element Method ◽  
Load Bearing Capacity ◽  
Natural Oscillations ◽  
Load Bearing ◽  
Resonance Frequencies ◽  
Element Method

AbstractThe actual load-bearing capacity of elements of a building system can be calculated by dynamic parameters, in particular by resonant frequency and compliance. The prerequisites for solving such a problem by the finite element method (FEM) are presented in the article. First, modern vibration tests demonstrate high accuracy in determination of these parameters, which reflects reliability of the diagnosis. Secondly, most modern computational complexes do not include a functional for calculating the load-bearing capacity of an element according to the input values of resonance frequencies. Thirdly, FEM is the basis for development of software tools for automating the computation process. The article presents the method for calculating flexural stiffness and moment of inertia of a beam construction system by its own frequencies. The method includes calculation algorithm realizing the finite element method.

scholarly journals Analysis of Load-Bearing Capacity of Initial lining in Tunnels

2021 ◽  
Vol 9 (VII) ◽  
pp. 3954-3960
Author(s):  
MD Waquar Alam
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Bearing Capacity ◽  
Element Model ◽  
Time Dependent ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Full Face ◽  
Ground Condition ◽  
Drill And Blast

Large displacements during excavation are regularly observed in Squeezing ground condition and Rock-burst condition with high overburden. The expected displacement has to be estimated prior to excavation to provide enough allowance for the displacements. The support system need to be well-suited through the estimated imposed strains. As the estimated displacements and thus the strains in the support depend upon the load-bearing capacity of support. The ratio of uniaxial compressive strength of rock mass to maximal insitu stress determines tunnel integrity in the weak region.This ratio estimates the requirements of initial lining to control strain to a stipulated level. The elasto-plastic theory may deliver definitive forecasts providing the strength limitations of rock masses are identified accurately. With the help of empirical analysis, the development of displacements for diverse advance rates and supports can be concluded. As a consequence, a quantitative finite element model based on an advanced built-in model is designed to analyse the load-bearing efficiency of initial lining although taking into consideration the time-dependent and non-linear material behaviour of initial lining. The time-dependent excavation mechanism of the drill-and-blast approach for tunnels guided by full face excavation is considered in the finite element model. The material parameters for the initial lining were computed based on case studies- (A Chibro-Khodri Hydropower Tunnel).

Simulation of Performance of CFST Elements Containing Differentiated Profile Tubes Filled with Reinforced Concrete

2019 ◽  
Vol 968 ◽  
pp. 281-287 ◽  
Author(s):  
Glib Vatulia ◽  
Alexey Lobiak ◽  
Vitaliy Chernogil ◽  
Mariia Novikova
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Accurate Method ◽  
Iteration Algorithm ◽  
Stress Strain ◽  
Load Bearing Capacity ◽  
Limiting State ◽  
Load Bearing ◽  
The Core

The approach to calculating CFST elements is considered in which physical non-linearity of materials, geometric non-linearity of the tube and the effect of increasing the strength of the core are taken into account. Finite element models are developed and proposed as the basis for more accurate method of calculating concrete-filled steel elements consisting of differentiated profile tubes filled with reinforced concrete. The technique uses a step iteration algorithm involving analytical dependencies and finite element simulation. The criterion for determining the load bearing capacity of CFST elements was the achievement of the stresses in the tube of the characteristic strength. The possibility of estimating the load bearing capacity of elements by limiting stresses in the core concrete is also implemented. The result of the calculations was obtaining the stress-strain and limiting state of the differentiated profile tubes with CFST elements, and graphic analysis of the regularities of stress redistribution at different stages of performance of columns. In general, with the accepted problem statement we could establish the exact stress-strain state, take into account the elastic-plastic deformations of concrete, its cracking and destruction, and geometric nonlinearity of the tube. The effect of performance of the corrugated sheet as a tube was established.

Experimental Research and Finite Element Analysis on the Axial Pressure Bearing Capacity of Steel skeleton-Steel Pipe Reinforced Composite Concrete Columns

2012 ◽  
Vol 204-208 ◽  
pp. 995-998
Author(s):  
Yun Yun Li ◽  
Bao Sheng Yang
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Concrete Columns ◽  
Steel Pipe ◽  
Axial Pressure ◽  
Load Bearing Capacity ◽  
Element Analysis ◽  
Load Bearing ◽  
Finite Element Software ◽  
Reinforced Composite

This paper studies the working mechanism, ductility, and ultimate load bearing capacity of the composite columns through axial load bearing capacity experiments on eight steel skeleton-steel pipes reinforced composite concrete columns. The results show that the collaborative work between the steel pipe, steel skeleton and concrete can effectively improve the bearing capacity of the column, delay or inhibit the spread of shear diagonal cracks in the concrete and improve the ductility of the column. In addition, the finite element software ANSYS is used to digitally simulate the whole process of axial pressure test, and the resulting load-displacement curves and experimental curves agree fairly well.

Sign in / Sign up

Export Citation Format

Share Document