scholarly journals Energy efficiency and transient-steady state performance comparison of a resistance infant incubator and an improved thermoelectric infant incubator

2021 ◽  
Author(s):  
Osman Yeler ◽  
Mehmet Fevzi Koseoglu
Keyword(s):  
Energy Efficiency ◽  
Steady State ◽  
Performance Comparison ◽  
Infant Incubator ◽  
Steady State Performance

A novel design of optimal intelligent fuzzy TID controller employing GA for nonlinear level control problem subject to actuator and system component fault

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Himanshukumar R. Patel ◽  
Sejal K. Raval ◽  
Vipul A. Shah
Keyword(s):  
Steady State ◽  
Pid Controller ◽  
Absolute Error ◽  
Performance Comparison ◽  
System Component ◽  
Content Type ◽  
Transient And Steady State ◽  
Steady State Performance ◽  
A Performance

PurposeThe purpose of this article is about the design of controllers for conical two-tank noninteracting level (CTTNL) system in simulation. Local linearization around the equilibrium point has been done for the nonlinear CTTNL system to obtain a linearized model transfer function.Design/methodology/approachThis article deals with the design of novel optimal fractional-order tilt-integral-derivative (TID) controller using type-1 fuzzy set for the CTTNL prototype system. In this study, type-1 fuzzy TID controller parameters have been optimized through genetic algorithm (GA) and those set of values have been employed for the design of proportional-integral-derivative (PID) controller.FindingsA performance comparison between FTID and PID controller is then investigated. The analysis shows the superiority of FTID controller over PID controller in terms of integral absolute error (IAE), integral square error (ISE), integral of time multiplied absolute error (ITAE) and integral of time multiplied squared error (ITSE) integral errors. The transient and steady state performance of the FTID controller are superior as compared to conventional PID controller. In future, the FTID controller fault-tolerance capability tested on CTTNL system subject to actuator and system component (leak) faults. The detailed study of robustness in presence of model uncertainties will be incorporated as a scope of further research.Originality/valueA performance comparison between FTID and PID controller is then investigated. The analysis shows the superiority of FTID controller over PID controller in terms of IAE, ISE, ITAE and ITSE integral errors. Additionally, fault-tolerant performance of the proposed controller evaluated with fault-recovery time (Frt) parameter. The transient and steady state performance of the FTID controller are superior as compared to conventional PID controller.

scholarly journals Dynamic and steady state performance comparison of line-start permanent magnet synchronous motors with interior and surface rotor magnets

2016 ◽  
Vol 65 (1) ◽  
pp. 105-116 ◽  
Author(s):  
Cosmas Ogbuka ◽  
Cajethan Nwosu ◽  
Marcel Agu
Keyword(s):  
Steady State ◽  
Permanent Magnet ◽  
Permanent Magnet Synchronous Motor ◽  
Synchronous Motor ◽  
Performance Comparison ◽  
Permanent Magnet Synchronous Motors ◽  
Synchronous Motors ◽  
Synchronous Mode ◽  
Interior Permanent Magnet ◽  
Steady State Performance

Abstract A comprehensive comparison of the dynamic and steady state performance characteristics of permanent magnet synchronous motors (PMSM) with interior and surface rotor magnets for line-start operation is presented. The dynamic model equations of the PMSM, with damper windings, are utilized for dynamic studies. Two typical loading scenarios are examined: step and ramp loading. The interior permanent magnet synchronous motor (IPMSM) showed superior asynchronous performance under no load, attaining faster synchronism compared to the surface permanent magnet synchronous motor (SPMSM). With step load of 10 Nm at 2 s the combined effect of the excitation and the reluctance torque forced the IPMSM to pull into synchronism faster than the SPMSM which lacks saliency. The ability of the motors to withstand gradual load increase, in the synchronous mode, was examined using ramp loading starting from zero at 2 s. SPMSM lost synchronism at 12 s under 11 Nm load while the IPMSM sustained synchronism until 41 seconds under 40 Nm load. This clearly suggests that the IPMSM has superior load-withstand capability. The superiority is further buttressed with the steady state torque analysis where airgap torque in IPMSM is enhanced by the reluctance torque within 90° to 180° torque angle.

Quasi-steady-state performance of a heat pipe subjected to transient acceleration loadings

10.2514/3.895 ◽  
1997 ◽  
Vol 11 ◽  
pp. 306-309 ◽  
Author(s):  
Edwin H. Olmstead ◽  
Edward S. Taylor ◽  
Meng Wang ◽  
Parviz Moin ◽  
Scott K. Thomas ◽  
...  
Keyword(s):  
Steady State ◽  
Heat Pipe ◽  
Quasi Steady State ◽  
Steady State Performance

A Novel Control Scheme for PWM Boost Converter based on Sliding Mode Control using Particle Swarm Optimization

2020 ◽  
Vol 14 ◽  
Author(s):  
Gang Liu ◽  
Dong Qiu ◽  
Xiuru Wang ◽  
Ke Zhang ◽  
Huafeng Huang ◽  
...  
Keyword(s):  
Particle Swarm Optimization ◽  
Steady State ◽  
Sliding Mode ◽  
Particle Swarm ◽  
Mathematic Model ◽  
Absolute Error ◽  
Boost Converter ◽  
Sliding Mode Controller ◽  
Swarm Optimization ◽  
Steady State Performance

Background: The PWM Boost converter is a strongly nonlinear discrete system, especially when the input voltage or load varies widely, therefore, tuning the control parameters of which is a challenge work. Objective: In order to overcome the issues, particle swarm optimization (PSO) is employed for tuning the parameters of a sliding mode controller of a boost converter. Methods: Based on the analysis of the Boost converter model and its non-linear characteristics, a mathematic model of a boost converter with a sliding mode controller is built firstly. Then, the parameters of the Boost controller are adjusted based on the integrated time and absolute error (ITAE), integral square error (ISE) and integrated absolute error (IAE) indexes by PSO. Results: Simulation verification was performed, and the results show that the controllers tuned by the three indexes all have excellent robust stability. Conclusion: The controllers tuned by ITAE and ISE indexes have excellent steady-state performance, but the overshoot is large during the startup. The controller tuned by IAE index has better startup performance and slightly worse steady-state performance.

Sign in / Sign up

Export Citation Format

Share Document