Effects of cooling rate on mechanical properties and corrosion resistance of vacuum sintered powder injection molded 316L stainless steel

2012 ◽  
Vol 212 (1) ◽  
pp. 164-170 ◽  
Author(s):  
M. Rafi Raza ◽  
Faiz Ahmad ◽  
M.A. Omar ◽  
R.M. German
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Cooling Rate ◽  
316L Stainless Steel ◽  
Powder Injection ◽  
Sintered Powder ◽  
Injection Molded ◽  
Mechanical Properties And Corrosion

Effects of Sintering Temperature and Cooling Rate on Mechanical Properties of Powder Injection Molded 316L Stainless Steel

2012 ◽  
Vol 185 ◽  
pp. 102-105
Author(s):  
Muhammad Rafi Raza Malik ◽  
Faiz Ahmad ◽  
Othman Mamat ◽  
Mohd Afian Omar ◽  
R.M. German ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Cooling Rate ◽  
316L Stainless Steel ◽  
Sintered Density ◽  
Steel Powder ◽  
Powder Injection ◽  
Heating And Cooling ◽  
Injection Molded ◽  
Effects Of Temperature

This research presents the effects of temperature and cooling rate on mechanical properties of powder injection molded 316L Stainless steel. Steel powder and binder were mixed together to produce the feedstock. The green samples were produced by injection molding and debinded. Brown test samples were sintered in vacuum at 1325°C, 1360°C and 1380°C for 2h with two heating and cooling rates 5°C/min and 10°C/ min. The test samples sintered at 1325°C achieved maximum sintered density. The higher cooling rate improved the strength of the sintered test samples. The maximum sintered density of 96% and tensile strength of 503MPa was achieved and these results are comparable to the wrought 316L stainless steel (according to ASTM standard).

Role of Debinding to Control Mechanical Properties of Powder Injection Molded 316L Stainless Steel

2013 ◽  
Vol 699 ◽  
pp. 875-882 ◽  
Author(s):  
Muhammad Rafi Raza ◽  
Faiz Ahmad ◽  
M.A. Omar ◽  
R.M. German ◽  
Ali S. Muhsan
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Injection Molding ◽  
316L Stainless Steel ◽  
Low Cost ◽  
Microstructural Analysis ◽  
Powder Injection ◽  
Laboratory Furnace ◽  
Injection Molded

316L stainless steel is widely used in various industries due to low cost, ease of availability and exceptional combination of mechanical properties along with corrosion resistance as compared to the other available metal alloys. In powder injection molding, debinding is very critical step and improper debinding can change the final properties dramatically. In the present study, affects of debinding on mechanical properties of powder injection molded 316L stainless steel were studied. The prepared feedstocks were molded according to MPIF 50 standard using vertical injection molding machine (KSA100). The plastic binder was removed at 450°C from the molded test samples using two different furnaces i.e. commercial and laboratory furnace followed by the sintering in vacuum, hydrogen, mixture of H2 and N2 (9:1) and nitrogen at 1325°C for 2hr with post sintering cooling rate 3°C/min . Test samples debound in commercially available furnace showed 97% densification and higher mechanical properties. The corrosion resistance was reduced due to presence of residual carbon during thermal debinding. The presence of carbon and formation of carbides and nitrides were confirmed by XRD and microstructural analysis. The results showed that the test samples debound in commercial furnace showed brittle behavior due to the presence of carbides and nitrides. Test samples sintered in N2 showed 96.3% density and tensile strength 751MPa. This value of strength is twice as compared to the sample debound in laboratory furnace followed by the sintering in vacuum. The achieved mechanical properties in vacuum sintered samples were comparable to the wrought 316L stainless steel (according to ASTM standard).

Preparation and Properties of Cu-10Sn Alloy Infiltrated 316L Stainless Steel Composites

2012 ◽  
Vol 503-504 ◽  
pp. 552-555 ◽  
Author(s):  
Xia Yang ◽  
Ying Long Bai ◽  
Meng Xu ◽  
Shi Ju Guo
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Powder Metallurgy ◽  
Matrix Composite ◽  
316L Stainless Steel ◽  
Corrosion Potential ◽  
Steel Matrix ◽  
Mechanical Properties And Corrosion ◽  
Steel Matrix Composite

A new method to produce powder metallurgy (P/M) 316L stainless steel matrix composite by pressureless infiltrating Cu-10Sn alloy was studied. The effect of various compaction pressures and infiltrating temperatures on the microstructure, mechanical properties and corrosion resistance was investigated. The results show that high density P/M 316L stainless steel matrix composite could be achieved by infiltration. A maximum relative density of 98% was achieved, provided that the porosity of the skeleton was controlled at 18%~22%. After infiltration, hardness of the samples increased from 49 HRB to 89 HRB. Moreover, the critical corrosion potential reached -212 mV, close to the level of as cast 316L stainless steel. The hardness of infiltrated composite of the same density decreased with increase in initial skeleton density. It was necessary to prevent the egregious grain growth while the infiltrating temperature was too high.

A Study on the Optimization of Solvent Debinding Process for Powder Injection Molded 316L Stainless Steel Parts

2016 ◽  
Vol 1133 ◽  
pp. 324-328 ◽  
Author(s):  
Muhammad Aslam ◽  
Faiz Ahmad ◽  
P.S.M. Bm-Yousoff ◽  
Khurram Altaf ◽  
Afian Omar ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
316L Stainless Steel ◽  
Research Work ◽  
Powder Injection ◽  
Blade Mixer ◽  
Injection Molded ◽  
Debinding Process ◽  
Scanning Electron

Optimization of solvent debinding process parameters for powder injection molded 316L stainless steel (SS) has been reported in this research work. Powder gas atomized (PGA) 316L SS was blended with a multicomponent binder in Z-blade mixer at 170°C ± 5°C for 90 minutes. Feedstock was successfully injected at temperature 170 ± 5°C. Injection molded samples were immersed in n-heptane for 2h, 4h, 6h and 8h at temperatures 50°C ,55°C and 60°C to extract the soluble binder components. Scanning electron microscope (SEM) results attested that soluble binder components were completely extracted from injection molded samples at temperature 55°C after 6h.

ATI 201 HP

Alloy Digest ◽  
2021 ◽  
Vol 70 (3) ◽  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Austenitic Stainless Steel ◽  
Physical Properties ◽  
Tensile Properties ◽  
Heat Treating ◽  
Mechanical Properties And Corrosion ◽  
Transportation Applications

Abstract ATI 201 HP is a 200-series, Cr-Mn-Ni austenitic stainless steel. It is comparable to the Cr-Ni stainless steel types 301, 304, and 304L in many respects, and can even provide some advantages over the 18-8 grades in certain applications. Because it possess a very desirable combination of economy plus good mechanical properties and corrosion resistance, it has been used in a wide variety of consumer and transportation applications. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, and joining. Filing Code: SS-1332. Producer or source: ATI.

Sign in / Sign up

Export Citation Format

Share Document