Wind and gravity mechanical effects on leaf inclination angles

2014 ◽  
Vol 341 ◽  
pp. 9-16 ◽  
Author(s):  
Loïc Tadrist ◽  
Marc Saudreau ◽  
Emmanuel de Langre
2021 ◽  
Vol 13 (7) ◽  
pp. 1405
Author(s):  
Jun Geng ◽  
Gang Yuan ◽  
J. M. Chen ◽  
Chunguang Lyu ◽  
Lili Tu ◽  
...  

As a widely used ground-based optical instrument, the LAI-2000 or LAI-2200 plant canopy analyzer (PCA) (Li-Cor, Inc., Lincoln, NE) is designed to measure the plant effective leaf area index (Le) by measuring the canopy gap fraction at several limited or discrete view zenith angles (VZAs) (usually five VZAs: 7, 23, 38, 53, and 68°) based on Miller’s equation. Miller’s equation requires the probability of radiative transmission through the canopy to be measured over the hemisphere, i.e., VZAs in the range from 0 to 90°. However, the PCA view angle ranges are confined to several limited ranges or discrete sectors. The magnitude of the error produced by the discretization of VZAs in the leaf area index measurements remains difficult to determine. In this study, a theoretical deduction was first presented to definitely prove why the limited or discrete VZAs or ranges can affect the Le measured with the PCA, and the specific error caused by the limited or discrete VZAs was described quantitatively. The results show that: (1) the weight coefficient of the last PCA ring is the main cause of the error; (2) the error is closely related to the leaf inclination angles (IAs)—the Le measured with the PCA can be significantly overestimated for canopies with planophile IAs, whereas it can be underestimated for erectophile IAs; and (3) the error can be enhanced with the increment of the discrete degree of PCA rings or VZAs, such as using four or three PCA rings. Two corrections for the error are presented and validated in three crop canopies. Interestingly, although the leaf IA type cannot influence the Le calculated by Miller’s equation in the hemispheric space, it affects the Le measured with the PCA using the discrete form of Miller’s equation for several discrete VZAs.


Forests ◽  
2020 ◽  
Vol 12 (1) ◽  
pp. 30
Author(s):  
Jie Zou ◽  
Peihong Zhong ◽  
Wei Hou ◽  
Yong Zuo ◽  
Peng Leng

The leaf inclination angle distribution function is a key determinant that influences radiation penetration through forest canopies. In this study, the needle and shoot inclination angle distributions of five contrasting Larix principis-rupprechtii plots were obtained via the frequently used leveled digital camera photography method. We also developed a quasi-automatic method to derive the needle inclination angles based on photographs obtained using the leveled digital camera photography method and further verified using manual measurements. Then, the variations of shoot and needle inclination angle distributions due to height levels, plots, and observation years were investigated. The results showed that the developed quasi-automatic method is effective in deriving needle inclination angles. The shoot and needle inclination angle distributions at the whole-canopy scale tended to be planophile and exhibited minor variations with plots and observation years. The small variations in the needle inclination angle distributions with height level in the five plots might be caused by contrasting light conditions at different height levels. The whole-canopy and height level needle projection functions also tended to be planophile, and minor needle projection function variations with plots and observation years were observed. We attempted to derive the shoot projection functions of the five plots by using a simple and applicable method and further evaluated the performance of the new method.


2018 ◽  
Vol 75 (2) ◽  
Author(s):  
Francesco Chianucci ◽  
Jan Pisek ◽  
Kairi Raabe ◽  
Luca Marchino ◽  
Carlotta Ferrara ◽  
...  

2020 ◽  
pp. 116-122
Author(s):  
Emre Öztürk ◽  
Mehmet Aktaş ◽  
Tunç Şenyüz

The purpose of this research is to reach good correlation between sun load simulation and solar focusing test for exterior automotive lighting products. Light coming from sun is highly collimated (parallel rays) and focusable from lenses with concave structure. Focusing incidence leads to a hot spot on lens surrounding plastic parts which may cause melting failures at high temperature zones. Sun load simulation is performing to eliminate risk of discoloration, deformation, out gassing, coating failures and fire with prolonged exposure from field. Irradiance values in W/m2 defined in simulation as heat source depending of an angle of incidence of the sun radiation. At first step, simulation is performing with 5 degree intervals to define the critical zones then intervals decreased to 2 degree to detect the critical azimuth and inclination angles. Critical azimuth and inclination angles is checking with ray trace analysis to check the bouncing of sun rays and possible solution to eliminate focuses with design solutions. After numerical analysis to release and validate the automotive lighting products regarding the sun load test, measurement with first parts is necessary. Measurement is performing for all critical angles which have been detected at simulation with thermal camera under ultra high-collimation solar simulator. Measured temperatures are settled according to environment conditions and correlation is checking with simulations.


Sign in / Sign up

Export Citation Format

Share Document