scholarly journals Microstructure development in a high-nickel austenitic stainless steel using EBSD during in situ tensile deformation

2018 ◽  
Vol 135 ◽  
pp. 228-237 ◽  
Author(s):  
K. Yvell ◽  
T.M. Grehk ◽  
P. Hedström ◽  
A. Borgenstam ◽  
G. Engberg
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Tensile Deformation ◽  
Microstructure Development ◽  
High Nickel

In-situ EBSD study of the degradation behavior in a type 316 Austenitic Stainless Steel during plastic deformation

2021 ◽  
pp. 030932472098493
Author(s):  
Xiao Wang ◽  
Yuetao Zhang ◽  
Huaying Li ◽  
Ming-yu Huang
Keyword(s):  
Plastic Deformation ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Tensile Deformation ◽  
Target Surface ◽  
Local Orientation ◽  
Deformation Degree ◽  
Band Contrast

Type 316 steels have been heavily utilized as the structural material in many construction equipment and infrastructures. This paper reports the characterization of degradation in 316 austenitic stainless steel during the plastic deformation. The in-situ EBSD results revealed that, with the increase of plastic strain, the band contrast (BC) value progressively decreased in both grain and grain boundaries, and the target surface becomes uneven after the plastic tensile, which indicates that the increase of surface roughness. Meanwhile, the KAM and ρGND values are low in the origin specimen but increased significantly after the in-situ tensile. The results indicated that the KAM and ρGND are closely related to the deformation degree of the materials, which can be used as the indicator for assessing the degradation of 316 steel. Besides, the re-orientation of grain occurred after the tensile deformation, which can be recognized from the lattice orientation and local orientation maps.

scholarly journals In Situ studies of the dynamics of strain fields in welded joints of austenitic stainless steel under tensile loads

2020 ◽  
Vol 30 ◽  
pp. 53-58
Author(s):  
Kirill Kurgan ◽  
Anatoliy Klopotov ◽  
Vasiliy Klimenov ◽  
Michael Slobodyan ◽  
Artem Ustinov ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Welded Joints ◽  
Strain Fields ◽  
In Situ Studies

Effects of Deformation Mode on Resistivity Curve Used for Estimating Martensite Induced in Stainless Steel

2010 ◽  
Vol 638-642 ◽  
pp. 2992-2997 ◽  
Author(s):  
Hidefumi Date
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Linear Relation ◽  
Volume Fraction ◽  
Tensile Deformation ◽  
Deformation Mode ◽  
Transformation Process ◽  
Martensite Formation ◽  
Austenitic Phase ◽  
Ε Phase

The martensite induced in three types of austenitic stainless steel, which indicate the different stability of the austenitic phase (γ), were estimated by the resistivity measured during the tensile deformation or compressive deformation at the temperatures 77, 187 and 293 K. The resistivity curves were strongly dependent on the deformation mode. The volume fraction of the martensite (α’) was also affected by the deformation mode. The ε phase, which is the precursor of the martensite and is induced from the commencement of the deformation, decreased the resistivity. However, lots of defects generated by the deformation-induced martensite increased the resistivity. The experimental facts and the results shown by the modified parallelepiped model suggested a complicated transformation process depending on each deformation mode. The results shown by the model also suggested a linear relation between the resistivity and the martensite volume at the region of the martensite formation. The fact denoted that the resistivity is mostly not controlled by the austenite, ε phase and martensite, but by the defects induced due to the deformation-induced martensite.

METHODS FOR THE IN-SITU CHARACTERIZATION OF CAST AUSTENITIC STAINLESS STEEL MICROSTRUCTURES

2011 ◽  
Author(s):  
P. Ramuhalli ◽  
M. S. Good ◽  
R. J. Harris ◽  
L. J. Bond ◽  
C. O. Ruud ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
In Situ Characterization
Sign in / Sign up

Export Citation Format

Share Document