scholarly journals Numerical Study of the Aggregate Contact Effect on the Complex Modulus of Asphalt Concrete

2021 ◽  
pp. 110342
Author(s):  
Zhifei Tan ◽  
Zhen Leng ◽  
Jiwang Jiang ◽  
Peng Cao ◽  
Denis Jelagin ◽  
...  
Keyword(s):  
Asphalt Concrete ◽  
Complex Modulus ◽  
Numerical Study ◽  
Contact Effect

The Viscoelastic Characteristics of the Asphalt Concrete Modified with Different Synthetic Waxes Using a Modified Huet- Sayegh Model

2017 ◽  
Author(s):  
Grzegorz Mazurek
Keyword(s):  
Asphalt Concrete ◽  
Dynamic Modulus ◽  
Complex Modulus ◽  
Model Parameters ◽  
Fischer Tropsch ◽  
Stiffness Modulus ◽  
Molecular Weights ◽  
Cole Diagram ◽  
Sinusoidal Load ◽  
Viscoelastic Characteristics

The article presents the results of dynamic modulus tests carried on the asphalt concrete (AC16W). The sinusoidal load was applied to the samples in accordance with DTC-CY method. The neat bituminous binder (penetration grade 35/50) was modified by means two synthetic waxes, coming from the Fischer-Tropsch raction, with various molecular weights and softening point temperature results (hard and softer). The relaxation phenomenon in terms of changes in complex modulus and phase angle was evaluated using the modified Huet-Sayegh (2S2P1D). Estimated model parameters pointed out that the addition of the synthetic wax with the high (hard wax) and the low (softer wax) molecular weight raised the stiffness of the bituminous binder in relation to the reference bitumen 35/50. The application of the modified Huet-Sayegh model showed that the presence of the synthetic wax in the bitumen significantly affected the stiffness modulus of considered asphalt concretes. Basing analysis on Cole-Cole diagram it was found significant differences in the viscoelastic behaviour between the reference asphalt concrete and the asphalt concretes with synthetic waxes. In contrast, there were no significant differences between viscoelastic properties of tested asphalt concretes modified, used in the experiment, synthetic waxes. Furthermore, the sensitivity to the loading time of asphalt concretes containing both synthetic waxes was marginal.

scholarly journals Characterizing the Complex Modulus of Asphalt Concrete Using a Scanning Laser Doppler Vibrometer

Materials ◽  
2019 ◽  
Vol 12 (21) ◽  
pp. 3542
Author(s):  
Navid Hasheminejad ◽  
Cedric Vuye ◽  
Alexandros Margaritis ◽  
Wim Van den bergh ◽  
Joris Dirckx ◽  
...  
Keyword(s):  
Asphalt Concrete ◽  
Master Curve ◽  
Complex Modulus ◽  
Optical Measurement ◽  
Laser Doppler Vibrometer ◽  
Beam Theory ◽  
Asphalt Mixtures ◽  
Laser Doppler ◽  
Bending Test ◽  
High Frequencies

Asphalt mixtures are the most common types of pavement material used in the world. Characterizing the mechanical behavior of these complex materials is essential in durable, cost-effective, and sustainable pavement design. One of the important properties of asphalt mixtures is the complex modulus of elasticity. This parameter can be determined using different standardized methods, which are often expensive, complex to perform, and sensitive to the experimental setup. Therefore, recently, there has been considerable interest in developing new, easier, and more comprehensive techniques to investigate the mechanical properties of asphalt. The main objective of this research is to develop an alternative method based on an optical measurement technique (laser Doppler vibrometry). To do this, a frequency domain system identification technique based on analytical formulas (Timoshenko’s beam theory) is used to determine the complex modulus of asphalt concrete at its natural frequencies and to form their master curve. The master curve plotted by this method is compared with the master curve obtained from the standard four-point bending test, and it is concluded that the proposed method is able to produce a master curve similar to the master curve of the standard method. Therefore, the proposed method has the potential to replace the standard stiffness tests. Furthermore, the standard stiffness methods usually conduct experiments up to the maximum frequency of 30 Hz. However, the proposed method can provide accurate complex modulus at high frequencies. This makes an accurate comparison between the properties of the asphalt mixtures in high frequencies and the development of more accurate theoretical models for simulation of specimens possible.

Specimen Geometry Study for Direct Tension Test Based on Mechanical Tests and Air Void Variation in Asphalt Concrete Specimens Compacted by Superpave Gyratory Compactor

2000 ◽  
Vol 1723 (1) ◽  
pp. 125-132 ◽  
Author(s):  
Ghassan R. Chehab ◽  
Emily O’Quinn ◽  
Y. Richard Kim
Keyword(s):  
Asphalt Concrete ◽  
Tensile Testing ◽  
Complex Modulus ◽  
Specimen Geometry ◽  
Uniaxial Tensile ◽  
Void Content ◽  
Uniaxial Tensile Testing ◽  
Superpave Gyratory Compactor ◽  
Air Void ◽  
Air Void Content

Reliable materials characterization and performance prediction testing of asphalt concrete requires specimens that can be treated as statistically homogeneous and representative of the material being tested. The objective of this study was to select a proper specimen geometry that could be used for uniaxial tensile testing. Selection was based on the variation of air void content along the height of specimens cut and cored from specimens compacted by the Superpave gyratory compactor (SGC) and on the representative behavior under mechanical testing. From measurement and comparison of air void contents in cut and cored specimens, it was observed for several geometries that sections at the top and bottom and those adjacent to the mold walls have a higher air void content than do those in the middle. It is thus imperative that test specimens be cut and cored from larger-size SGC specimens. Complex modulus and constant crosshead-rate monotonic tests were conducted for four geometries—75 × 115, 75 × 150, 100 × 150, and 100 × 200 mm—to study the effect of geometry boundary conditions on responses. On the basis of graphical and statistical analysis, it was determined that there was an effect on the dynamic modulus at certain frequencies but no effect on the phase angle. Except for 75 × 115 mm, all geometries behaved similarly under the monotonic test. From these findings and other considerations, it is recommended that the 75- × 150-mm geometry, which is more conservative, and the 100- × 150-mm geometry be used for tensile testing.

Effectiveness of static and dynamic backcalculation approaches for asphalt pavement

2020 ◽  
Vol 47 (7) ◽  
pp. 846-855
Author(s):  
Dandan Cao ◽  
Changjun Zhou ◽  
Yanqing Zhao ◽  
Guozhi Fu ◽  
Wanqiu Liu
Keyword(s):  
Asphalt Concrete ◽  
Elastic Moduli ◽  
Complex Modulus ◽  
Asphalt Pavement ◽  
Falling Weight Deflectometer ◽  
Fixed Frequency ◽  
Dynamic Approach ◽  
Layer Effect ◽  
Static Approach ◽  
Falling Weight

In this study, the field falling weight deflectometer (FWD) data for asphalt pavement with various base types were backcalculated through dynamic and static backcalculation approaches, and the effectiveness of backcalculation approaches was studied. Asphalt concrete (AC) was treated as a viscoelastic material and the complex modulus was obtained using the dynamic approach. The dynamic modulus at a fixed frequency was computed for comparison purposes. The coefficient of variance and the compensating layer effect were assumed as two characteristics for the effectiveness of backcalculation approaches. The results show that the layer property from the dynamic backcalculation approach for different stations were more consistent and showed smaller coefficient of variance, which were more appropriate for the characterization pavement behavior. The elastic moduli from the static approach were more variable and exhibited a compensating layer effect in which a portion of the modulus of one layer was backcalculated into other layers. The dynamic approach is more effective than static approaches in backcalculation of layer properties.

Interpretation of Indirect Tension Test Based on Viscoelasticity

1997 ◽  
Vol 1590 (1) ◽  
pp. 45-52 ◽  
Author(s):  
A. Drescher ◽  
D. E. Newcomb ◽  
W. Zhang
Keyword(s):  
Asphalt Concrete ◽  
Complex Modulus ◽  
Resilient Modulus ◽  
Traditional Approach ◽  
Test Methods ◽  
Tension Test ◽  
Current Test ◽  
Indirect Tension ◽  
Materials Used ◽  
Indirect Tension Test

The diametral indirect tension test is a convenient configuration for determining the modulus of asphalt concrete samples. The resilient modulus test has been a traditional approach to characterizing the stiffness of asphalt concrete, but it leaves much to be desired when considering the viscous behavior this material exhibits, even at low temperatures. A method for determining the complex compliance, complex modulus, and phase angle of asphalt mixtures using the indirect tensile test and a haversine load history is presented here. This test may be performed over a range of frequencies and temperatures as demonstrated on materials used in the Minnesota Road Research Project. The use of the haversine loading simplifies the test when compared with the pulse loading and rest time used in the resilient modulus test, and it allows for the characterization of the elastic and viscous components of the material's overall behavior, which is very difficult, at best, with the current test methods.

Mechanistic-Based Approach to Utilize Traffic Speed Deflectometer Measurements in Backcalculation Analysis

2020 ◽  
Vol 2674 (5) ◽  
pp. 208-222
Author(s):  
Zia U. A. Zihan ◽  
Mostafa A. Elseifi ◽  
Patrick Icenogle ◽  
Kevin Gaspard ◽  
Zhongjie Zhang
Keyword(s):  
Asphalt Concrete ◽  
Traffic Control ◽  
Parametric Study ◽  
Complex Modulus ◽  
Falling Weight Deflectometer ◽  
Software Application ◽  
Traffic Speed ◽  
Definition Of ◽  
Falling Weight ◽  
Surface Deflections

Backcalculation analysis of pavement layer moduli is typically conducted based on falling weight deflectometer (FWD) deflection measurements; however, the stationary nature of the FWD requires lane closure and traffic control. In recent years, traffic speed deflection devices such as the traffic speed deflectometer (TSD), which can continuously measure pavement surface deflections at traffic speed, have been introduced. In this study, a mechanistic-based approach was developed to convert TSD deflection measurements into the equivalent FWD deflections. The proposed approach uses 3D-Move software to calculate the theoretical deflection bowls corresponding to FWD and TSD loading configurations. Since 3D-Move requires the definition of the constitutive behaviors of the pavement layers, cores were extracted from 13 sections in Louisiana and were tested in the laboratory to estimate the dynamic complex modulus of asphalt concrete. The 3D-Move generated deflection bowls were validated with field TSD and FWD data with acceptable accuracy. A parametric study was then conducted using the validated 3D-Move model; the parametric study consisted of simulating pavement designs with varying thicknesses and material properties and their corresponding FWD and TSD surface deflections were calculated. The results obtained from the parametric study were then incorporated into a Windows-based software application, which uses artificial neural network as the regression algorithm to convert TSD deflections to their corresponding FWD deflections. This conversion would allow backcalculation of layer moduli using TSD-measured deflections, as equivalent FWD deflections can be used with readily available tools to backcalculate the layer moduli.

Sign in / Sign up

Export Citation Format

Share Document