Experimental investigation on dry sliding wear resistance of recently developed hyper-duplex stainless steel

2020 ◽  
Vol 22 ◽  
pp. 2172-2178
Author(s):  
P. NithinRaj ◽  
Nithin Sivadas ◽  
K. Sekar ◽  
M.A. Joseph
Keyword(s):  
Experimental Investigation ◽  
Stainless Steel ◽  
Wear Resistance ◽  
Duplex Stainless Steel ◽  
Sliding Wear ◽  
Dry Sliding Wear ◽  
Dry Sliding

scholarly journals Structural and Tribological Assessment of Biomedical 316 Stainless Steel Subjected to Pulsed-Plasma Surface Modification: Comparison of LPBF 3D Printing and Conventional Fabrication

Materials ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 7671
Author(s):  
Yuliia Chabak ◽  
Bohdan Efremenko ◽  
Ivan Petryshynets ◽  
Vasily Efremenko ◽  
Angeliki G. Lekatou ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Wear Resistance ◽  
Sliding Wear ◽  
Structural Features ◽  
Discharge Voltage ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Pulsed Plasma ◽  
316 Stainless Steel ◽  
Wear Response

The structural features and nanoindentation/tribological properties of 316 stainless steel fabricated by conventional rolling and laser-based powder bed fusion (LPBF) were comparatively investigated regarding the effect of surface-pulsed plasma treatment (PPT). PPT was performed using an electrothermal axial plasma accelerator under a discharge voltage of 4.5 kV and a pulse duration of 1 ms. Optical microscopy, scanning electron microscopy, X-ray diffraction, nanoindentation measurements and tribological tests were applied to characterize the alloys. The LPBF steel presented almost the same modulus of elasticity and double the hardness of rolled steel. However, the LPBF steel manifested lower dry-sliding wear resistance compared with its wrought counterpart due to its porous structure and non-metallic inclusions. Conversely, LPBF steel showed three times higher wear resistance under sliding in simulated body fluid (SBF), as compared with wrought steel. PPT led to steel modification through surface melting to a depth of 22–26 μm, which resulted in a fine cellular structure. PPT moderately improved the dry-sliding wear resistance of LPBF steel by fusion of pores on its surface. On the other hand, PPT had almost no effect on the SBF-sliding wear response of the steel. The modification features were analyzed using a computer simulation of plasma-induced heating.

Improving Wear Resistance of AISI 316LN Austenitic Stainless Steel Using Friction Stir Processing

2015 ◽  
Vol 787 ◽  
pp. 421-425
Author(s):  
A. Vignesh ◽  
V.G. Vijay Prakaash ◽  
A.K. Lakshminarayanan
Keyword(s):  
Stainless Steel ◽  
Wear Resistance ◽  
Austenitic Stainless Steel ◽  
Friction Stir Processing ◽  
Sliding Wear ◽  
Dry Sliding Wear ◽  
Friction Stir ◽  
Pin On Disc ◽  
Metal Microstructure ◽  
Equiaxed Grains

An attempt is made to modify the surface metallurgically and enhance the wear resistance of AISI 316LN austenitic stainless steel using friction stir processing. Friction stir welding tools made up of tungsten based alloy with pin and pinless configuration was used. Fine equiaxed grains were observed in the friction stir processed zone irrespective of tool configuration used. Dry sliding wear resistance was evaluated using pin-on-disc wear tester and it is found that, the friction stir processed zone showed superior wear resistance compared to the base metal. Microstructure, micro hardness, and worn surfaces were used to correlate the results obtained.

scholarly journals Effect of Necklace-Type Distribution of SiC Particles on Dry Sliding Wear Behavior of As-Cast AZ91D/SiCp Composites

Crystals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 296 ◽  
Author(s):  
Chao Sun ◽  
Nannan Lu ◽  
Huan Liu ◽  
Xiaojun Wang ◽  
Xiaoshi Hu ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Interface Bonding ◽  
Type Distribution ◽  
Wear Rates ◽  
Sic Particles ◽  
The Matrix

In this study, the dry sliding wear behaviors of SiC particle reinforced AZ91D matrix composites fabricated by stirring casting method were systematically investigated. The SiC particles in as-cast composites exhibited typical necklace-type distribution, which caused the weak interface bonding between SiC particles and matrix in particle-segregated zones. During dry sliding at higher applied loads, SiC particles were easy to debond from the matrix, which accelerated the wear rates of the composites. While at the lower load of 10 N, the presence of SiC particles improved the wear resistance. Moreover, the necklace-type distribution became more evident with the decrease of particle sizes and the increase of SiC volume fractions. Larger particles had better interface bonding with the matrix, which could delay the transition of wear mechanism from oxidation to delamination. Therefore, composites reinforced by larger SiC particles exhibited higher wear resistance. Similarly, owing to more weak interfaces in the composites with high content of SiC particles, more severe delamination occurred and the wear resistance of the composites was impaired.

Improving the Wear Resistance of Aluminum Fly Ash Composites by Multipass Friction Stir Processing

2015 ◽  
Vol 642 ◽  
pp. 55-59 ◽  
Author(s):  
Shueiwan Henry Juang ◽  
Liang Jing Fan ◽  
Hsu Shuo Chang
Keyword(s):  
Wear Resistance ◽  
Fly Ash ◽  
Friction Stir Processing ◽  
Sliding Wear ◽  
Normal Load ◽  
Aluminum Matrix ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Wear Rates ◽  
Friction Stir

In this study, the multi-pass friction stir processing (MP-FSP) technique was performed on ADC6 aluminum alloy + 5 wt% fly ash composite (A5FC) castings to increase their surface area. The dry sliding wear behaviors of the ADC6 alloy, A5FCs, and MP-FSPed A5FCs were evaluated. Dry sliding wear tests were performed using a ring-on-washer machine at a constant rotation speed of 100 rpm for 60 min, and the normal load was 10, 20, 30, and 40 N. The results showed that the MP-FSPed A5FCs had the lowest wear rates in the load range from 10 to 40 N, and adhesive wear was the major wear mechanism in these tests. The increased wear resistance was mainly due to grain refinement and elimination of casting defects after subjecting the ash composite to MP-FSP. The microstructure of the MP-FSPed A5FCs reveals that the sizes of the added raw fly ash particles decreased from micro-to nanoscale levels, and the nanoscale fly ash was uniformly dispersed in the aluminum matrix.

Sign in / Sign up

Export Citation Format

Share Document