Modeling of machining parameters affecting flank wear and surface roughness in hot turning of Monel-400 using response surface methodology (RSM)

Measurement ◽  
2019 ◽  
Vol 137 ◽  
pp. 375-381 ◽  
Author(s):  
Asit Kumar Parida ◽  
Kalipada Maity
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Flank Wear ◽  
Machining Parameters ◽  
Monel 400 ◽  
Hot Turning

scholarly journals Modeling and optimization of flank wear and surface roughness of Monel-400 during hot turning using artificial intelligence techniques

10.30544/473 ◽  
2020 ◽  
Vol 26 (1) ◽  
pp. 57-69
Author(s):  
M. Hanief ◽  
M. S. Charoo
Keyword(s):  
Surface Roughness ◽  
Power Law ◽  
Close Agreement ◽  
Flank Wear ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Power Law Model ◽  
Objective Functions ◽  
Monel 400 ◽  
Hot Turning

This work aims to model and investigate the effect of cutting speed, feed rate, depth of cut and the workpiece temperature on surface roughness and flank wear (responses) of Monel-400 during turning operation. It also aims to optimize the machining parameters of the above operation. A power-law model is developed for this purpose and is corroborated by comparing the results with the artificial neural network (ANN) model. Based on the coefficient of determination (R2), mean square error (MSE), and mean absolute percentage error (MAPE) the results of the power-law model are found to be in close agreement with that of ANN. Also, the proposed power law and ANN models for surface roughness and flank wear are in close agreement with the experiment results. For the power-law model R2, MSE, and MAPE were found to be 99.83%, 9.9×10-4, and 3.32×10-2, and that of ANN were found to be 99.91%, 5.4×10-4, and 5.96×10-2, respectively for surface roughness and flank wear. An error of 0.0642% (minimum) and 8.7346% (maximum) for surface roughness and 0.0261% (minimum) and 4.6073% (maximum) for flank wear were recorded between the observed and experimental results, respectively. In order to optimize the objective functions obtained from power-law models of the surface roughness and flank wear, GA (genetic algorithm) was used to determine the optimal values of the operating parameters and objective functions thereof. The optimal value of 2.1973 µm and 0.256 mm were found for surface roughness and flank wear, respectively.

Investigations on Surface Roughness Measurement in Minimum Quantity Lubrication Turning of Titanium Alloys Using Response Surface Methodology and Box–Cox Transformation

2016 ◽  
Vol 16 (2) ◽  
pp. 75-88 ◽  
Author(s):  
Munish Kumar Gupta ◽  
P. K. Sood ◽  
Vishal S. Sharma
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Flow Rate ◽  
Feed Rate ◽  
Cutting Speed ◽  
Minimum Quantity Lubrication ◽  
Machining Parameters ◽  
Minimum Quantity ◽  
Box Cox Transformation

AbstractIn the present work, an attempt has been made to establish the accurate surface roughness (Ra, Rq and Rz) prediction model using response surface methodology with Box–Cox transformation in turning of Titanium (Grade-II) under minimum quantity lubrication (MQL) conditions. This surface roughness model has been developed in terms of machining parameters such as cutting speed, feed rate and approach angle. Firstly, some experiments are designed and conducted to determine the optimal MQL parameters of lubricant flow rate, input pressure and compressed air flow rate. After analyzing the MQL parameter, the final experiments are performed with cubic boron nitride (CBN) tool to optimize the machining parameters for surface roughness values i. e., Ra, Rq and Rz using desirability analysis. The outcomes demonstrate that the feed rate is the most influencing factor in the surface roughness values as compared to cutting speed and approach angle. The predicted results are fairly close to experimental values and hence, the developed models using Box-Cox transformation can be used for prediction satisfactorily.

Experimental investigation of machinability and geometrical behavior of Titanium Alloy (Ti–6Al–4V) using Abrasive Waterjet Circular cut using Response Surface Methodology-Desirability approach

2021 ◽  
Author(s):  
Umanath Karuppusamy ◽  
Devika D ◽  
Rashia Begum S
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Titanium Alloy ◽  
Response Surface ◽  
Process Parameters ◽  
Abrasive Waterjet ◽  
Optimum Level ◽  
Machining Parameters ◽  
Input Parameters ◽  
Desirability Approach

Abstract In the current study, the research explored the effect of the process parameters on the Titanium Alloy (Ti–6Al–4V) to improve the machining, surface and geometric characteristics of the circular cut-off profile by determining the optimum parameters for the Abrasive Water Jet Machining (AWJM). The input parameters considered are the Abrasive Flow Rate (AFR), Stand-off Distance (SoD), and Traverse Rate (TR). There are various input parameters to evaluate output parameters like Circularity, Cylindricity, and Surface Roughness (SR) of the circular cut profile. The experiments are conducted using Central Composite Design (CCD) in the Response Surface Methodology (RSM). Analysis of variance (ANOVA) is carried out to define most influenced process parameters and percentage of contribution. The RSM is used to predict the mathematical models for formulating the objective function using experimental results. RSM desirability approach is included in the method for determining optimum levels and discerning impacts on response variables of machining parameters. Confirmation tests with an optimum level of machining parameters have been completed to determine the adequacy of the RSM. In addition to that, the cutting profiles are also analysed using Scanning Electron Microscope (SEM). The Atomic Force Microscope(AFM) is often used to verify the minimum Surface Roughness of the AWJM machined surface.

Surface Roughness Prediction in End Milling of Machinable Glass Ceramic and Optimization by Response Surface Methodology

2011 ◽  
Vol 189-193 ◽  
pp. 1376-1381
Author(s):  
Moola Mohan Reddy ◽  
Alexander Gorin ◽  
Khaled A. Abou El Hossein
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Glass Ceramic ◽  
End Milling ◽  
Removal Rate ◽  
Cutting Speed ◽  
Lower Surface ◽  
Depth Of Cut ◽  
Machining Parameters

This paper presents the prediction of a statistically analyzed model for the surface roughness,R_a of end-milled Machinable glass ceramic (MGC). Response Surface Methodology (RSM) is used to construct the models based on 3-factorial Box-Behnken Design (BBD). It is found that cutting speed is the most significant factor contributing to the surface roughness value followed by the depth of cut and feed rate. The surface roughness value decreases for higher cutting speed along with lower feed and depth of cut. Additionally, the process optimization has also been done in terms of material removal rate (MRR) to the model’s response. Ideal combinations of machining parameters are then suggested for common goal to achieve lower surface roughness value and higher MRR.

Surface Roughness Prediction in the End Milling Parameters of Aluminum Nitride Ceramic by Response Surface Methodology

2010 ◽  
Vol 154-155 ◽  
pp. 626-633
Author(s):  
Moola Mohan Reddy ◽  
Alexander Gorin ◽  
Khaled A. Abou-El-Hossein
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
End Milling ◽  
Cubic Boron Nitride ◽  
Cutting Speed ◽  
Machining Parameters ◽  
Roughness Model ◽  
Roughness Prediction ◽  
Grinding Tool

The present experimental study aimed to examine the selected machining parameters on Surface roughness in the machining of alumina nitride ceramic. The influence of cutting speed and feed rate were determined in end milling by using Cubic boron nitride grinding tool. The predictive surface roughness model has been developed by response surface methodology. The response surface contours with respect to input parameters are presented with the help of Design expert software. The adequacy of the model was tested by ANOVA.

Experimental Investigation of Process Parameters in Wire Electrical Discharge Machining by Response Surface Methodology on IS2062 Steel

2014 ◽  
Vol 550 ◽  
pp. 53-61
Author(s):  
R.Arun Bharathi ◽  
P.Ashoka Varthanan ◽  
K. Manoj Mathew
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Process Parameters ◽  
Machining Parameters ◽  
Peak Current ◽  
Custom Design ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

The objective of the present work is to predict the optimal set of process parameters such as peak current (IP), pulse on/off time (TON/TOFF) and spark gap voltage (SV) to achieve minimum Surface roughness (Ra), wire consumption rate (WCR) and maximum material removal rate (MRR). In this work, experiments were carried out by pulse arc discharges generated between ZnO coated brass wire and specimen (IS2062 steel) suspended in deionized water dielectric. The experiments were designed based on the above mentioned four factors, each having three levels. Custom design based Response Surface Methodology (RSM) is used in this research. 21 runs of experiments were constructed based on custom design procedure and results of the experimentation were analyzed analytically as well as graphically. Moreover the surface roughness after machining was measured by Taylor Hobson Surtronic device. Second order regression model has been developed for predicting Ra, WCR and MRR in terms of interactive and higher order machining parameters through RSM, utilizing relevant experimental data as obtained through experimentation. The research outcome identifies significant parametersand their effect on process performance on IS2062 steel. The results revealed that peak current, pulse on-time and their interactions have significant effects on Ra, whereas pulse off time and peak current have significant effects on MRR and it is also observed that peak current and interaction between peak current and pulse off time have significant effects on WCR. The adequacy of the above proposed models has been tested through the analysis of variance (ANOVA).

scholarly journals Optimization of Machining Parameters of Aluminum Alloy BS-1474 2014 A using Response Surface Methodology

2020 ◽  
Author(s):  
waqas javaid ◽  
Tauqeer Iqbal ◽  
Ammar ul Hassan
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Aluminum Alloy ◽  
Response Surface ◽  
Removal Rate ◽  
Machining Process ◽  
Interface Temperature ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Turning Process

Abstract High surface quality, optimum Material Removal Rate (MRR) and Tool-Chip Interface temperature (T c ) have significant importance in machining process. Similarly, dimensional accuracy in machining process also relies heavily on machining parameters. In machining operations, there are a number of parameters which have direct or indirect effect on the Surface Roughness (Ra) and MRR of the product. The surface roughness and MRR in turning process are affected by spindle speed (SS), feed rate (FR) and depth of cut (DOC). The optimization of turning parameters will be very helpful in improving quality of manufacturing and machining cost. In order to have an improved product, extensive research has been carried out to optimize machining process. The current research is focused at Response Surface Methodology (RSM) of turning process of Aluminum alloy (BS-1474 2014 A) by using variable sets of machining parameters i.e., SS, FR and DOC with carbide tipped tool. Multiple experiments were performed on CNC Lathe machine by using different combinations of process parameters. Response surface methodology was applied to reach theoretical values of the responses parameters (i.e, Ra, MRR, T c ) and an agreement was observed between actual machining results and methodology values. Design Expert-7 was used as a statistical tool to come to a conclusion on whether achieved results are optimum for turning process or otherwise. For a close correlation, comparison between hypothetical and investigational data is also the part of this research. Significant agreement between theoretically optimized machining parameters and experimental data has been observed.

Investigating and Modeling the Machinability of Al 6061 Using Response Surface Methodology

2015 ◽  
Vol 761 ◽  
pp. 267-272
Author(s):  
Basim A. Khidhir ◽  
Ayad F. Shahab ◽  
Sadiq E. Abdullah ◽  
Barzan A. Saeed
Keyword(s):  
Mathematical Model ◽  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Feed Rate ◽  
Cutting Speed ◽  
Effect Of Temperature ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Turning Process

Decreasing the effect of temperature, surface roughness and vibration amplitude during turning process will improve machinability. Mathematical model has been developed to predict responses of the surface roughness, temperature and vibration in relation to machining parameters such as the cutting speed, feed rate, and depth of cut. The Box-Behnken First order and second-order response surface methodology was employed to create a mathematical model, and the adequacy of the model was verified using analysis of variance. The experiments were conducted on aluminium 6061 by cemented carbide. The direct and interaction effect of the machining parameters with responses were analyzed. It was found that the feed rate, cutting speed, and depth of cut played a major role on the responses, such as the surface roughness and temperature when machining mild steel AISI 1018. This analysis helped to select the process parameters to improve machinability, which reduces cost and time of the turning process.

scholarly journals Optimization of Surface Roughness of Turned Nano-Khorasan Based Madar Fiber Composites Using Response Surface Methodology

2019 ◽  
Vol 8 (10) ◽  
pp. 253-257
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Natural Fiber ◽  
Relative Effect ◽  
Experimental Result ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Fiber Reinforced ◽  
Reinforced Polymer

Now a day Nano based Natural Fiber Reinforced Polymer (NFRP) composite is important alternative material to conventional materials because of its superior characteristics. In general composite products are manufactured nearer to the required shape, but secondary operations like machining is necessary to obtain the required surface finish. Machining of NFRP composites is different than the machining of traditional materials. This paper focuses on the behavior and optimization of machining parameters on turning of Nano-Khorasan based madar fiber reinforced composites by using Response Surface Methodology (RSM) technique. The input factors studied are speed, feed, depth of cut and Nano-Khorasan mixing. The investigated output response was Average Surface Roughness (Ra). A Box- Behnken approach was employed to evaluate the optimum parameters to attain the minimum Ra. Based on this approach, a second order polynomial modal equation was generated for predicting response Ra. Also the relative effect of parameters on response Ra was studied by using ANOVA. The experimental result shows some interesting factors in context to the turning of Nano Khorasan based Madarfiber reinforced polymer composites

Sign in / Sign up

Export Citation Format

Share Document