Effect of process parameters on abnormal grain growth during friction stir processing of a cast Al alloy

2010 ◽  
Vol 528 (1) ◽  
pp. 189-199 ◽  
Author(s):  
S. Jana ◽  
R.S. Mishra ◽  
J.A. Baumann ◽  
G. Grant
Keyword(s):  
Grain Growth ◽  
Process Parameters ◽  
Friction Stir Processing ◽  
Abnormal Grain Growth ◽  
Al Alloy ◽  
Friction Stir

Control of Grain Size and Texture in Al Alloys Utilizing Friction Stir Processing

2007 ◽  
Vol 539-543 ◽  
pp. 3769-3774 ◽  
Author(s):  
Toshiya Shibayanagi ◽  
Masaaki Naka
Keyword(s):  
Grain Size ◽  
Aluminum Alloys ◽  
Grain Refinement ◽  
Grain Growth ◽  
Rotation Speed ◽  
Al Alloys ◽  
Abnormal Grain Growth ◽  
Texture Development ◽  
Al Alloy ◽  
Friction Stir

The present paper deals with the control of microstructure of friction stir processed aluminum alloys focusing on grain refinement, thermal stability at elevated temperature and texture development in some aluminum alloys such as 5083, 6061 and 7075 commercial aluminum alloys. 3mm thickness plates of 5083, 6061 and 7075 Al alloys were friction stir processed/welded with several rotation speeds and travelling speeds. Optical microscopy revealed the grain refinement in the stirred zone of each alloy and the average grain size decreased with decreasing rotation speed under various travelling speeds. Annealing of the joints brought about abnormal grain growth at temperatures higher than 773K for 5083 alloy. Critical temperature of the abnormal grain growth tended to decrease as the rotation speed decreased for the fixed travelling speed. Dissimilar joining of 5083 Al alloy to 6061 Al alloy also showed abnormal grain growth when annealed at 773K. A peculiar texture development of 7075 Al joint showing (111)//ND-oriented grains existing throughout the nugget was revealed by EBSP analysis.

scholarly journals Friction Stir Welding with Low-Medium-High Tool Travel Speed of 0.95 Mg-Al-Alloy and Pure Copper: Electrochemical and Surface Studies

2018 ◽  
Author(s):  
Neetesh Soni ◽  
Ambrish Singh
Keyword(s):  
Friction Stir Welding ◽  
Process Parameters ◽  
Pure Copper ◽  
Travel Speed ◽  
Localized Corrosion ◽  
Al Alloy ◽  
Kelvin Probe ◽  
Friction Stir ◽  
Surface Optical ◽  
Joining Process

The aim of this work is to assess the influence of Friction Stir Welding (FSW), process parameters, optimized tool traveling speed, and corrosion resistance of the 0.95 Mg-Al-alloy and pure copper weldment. Samples of aluminum-copper with and without deformation were characterized to investigate the metallurgical effects created during the welding deformation process. Effect of process parameters on microstructure and corrosion rate have been investigated for all the samples. All the electrochemical and polarization tests were done in 3.5 wt.% NaCl solution. Scanning Kelvin Probe (SKP) was done to detect the localized corrosion on the surface. Optical micrography observation indicated that the primary α-Al phase, which was formed during solidification can effectively limit the growth of Cu9Al4 phase. Finer acicular α-Al precipitates were observed in CuAl matrix during joining process that tends to coarser with the increase in tools travel speed. The electrochemical and polarization results showed that among all the tool travelling speed the specimen joined at tool travelling speed of 40 mm/min shows the best non-corrosive property.

scholarly journals Fabrication of AA7075 Hybrid Green Metal Matrix Composites by Friction Stir Processing Technique

2020 ◽  
Vol 44 (4) ◽  
pp. 295-300
Author(s):  
Sanjay Kumar ◽  
Ashish Kumar Srivastava ◽  
Rakesh Kumar Singh
Keyword(s):  
Mechanical Properties ◽  
Process Parameters ◽  
Friction Stir Processing ◽  
Research Work ◽  
Processing Technique ◽  
Matrix Composites ◽  
Avant Garde ◽  
Friction Stir ◽  
Surface Composites ◽  
Tool Tilt Angle

Friction stir processing is an avant-garde technique of producing new surface composite or changing the different properties of a material through intense, solid-state localized material plastic deformation. This change in properties depends upon the deformation formed by inserting a non-consumable revolving tool into the workpiece and travels laterally through the workpiece. This research work highlights the effect of process parameters on mechanical properties of fabricated surface composites by friction stir processing. By using various reinforcing materials like Ti, SiC, B4C, Al2O3 with waste elements like waste eggshells, rice husks, coconut shell and coir will be used to fabricate the green composites which are environmentally friendly and reduces the problem of decomposition. The parameter for this experiment is considered as the reinforcing materials, tool rotation speed and tool tilt angle. The SiC/Al2O3/Ti along with eggshell are selected asreinforcement materials. The main effect of the reinforcement is to improve mechanical properties, like hardness, impact strength and strength. The results revealed that the process parameters significantly affect the mechanical properties of friction stir processed surface composites.

Influence of Process Parameters on Microstructure of Friction Stir Processed Mg AZ31 Alloy

2017 ◽  
pp. 1293-1305
Author(s):  
G. Venkateswarlu ◽  
M.J. Davidson ◽  
G.R.N. Tagore ◽  
P. Sammaiah
Keyword(s):  
Plastic Deformation ◽  
Grain Refinement ◽  
Process Parameters ◽  
Tilt Angle ◽  
Friction Stir Processing ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Homogeneous Microstructure ◽  
Friction Stir ◽  
Tool Tilt Angle

Friction stir processing (FSP) has been developed on the principles of friction stir welding (FSW) as an effective and efficien new method for grain refinement and microstructural modification, providing intense plastic deformation as well as higher strain rates than other conventional severe plastic deformation methods. FSP produces an equiaxed homogeneous microstructure consisting of fine grains, resulting in the enhancement of the properties of the material at room temperature. The objective of the present paper is to examine the influence of friction stir processing (FSP) parameters namely tool rotational speed (RS), tool traverse speed (TS) and tool tilt angle (TA) on the microstructures of friction stir processed AZ31B-O magnesium alloy. This investigation has focused on the microstructural changes occurred in the dynamically recrystallised nugget zone/ stir zone and the thermo mechanically affected zone during FSP. The results presented in this work indicate that all the three FSP process parameters have a significant effect on the resulting microstructure and also found that the rotational speed has greatly influenced the homogenization of the material. The grain refinement is higher at intermediate rotational speed (1150 rpm), traverse speed (32 mm / min and tilt angle (10). It is established that FSP can be a good grain refinement method for improving the properties of the material.

scholarly journals Improvement of local ductility in cast Al-alloy due to friction stir processing

2012 ◽  
Vol 30 (2) ◽  
pp. 180-187
Author(s):  
Tetsuya TAGAWA ◽  
Ken IKAWA ◽  
Yohei KATSURAGI ◽  
Takeshi SHINODA ◽  
Fumiyoshi MINAMI
Keyword(s):  
Friction Stir Processing ◽  
Al Alloy ◽  
Friction Stir

scholarly journals Friction Stir Welding Parameters: Impact of Abnormal Grain Growth during Post-Weld Heat Treatment on Mechanical Properties of Al–Mg–Si Welded Joints

Metals ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1607
Author(s):  
Amir Hossein Baghdadi ◽  
Zainuddin Sajuri ◽  
Mohd Zaidi Omar ◽  
Armin Rajabi
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Friction Stir Welding ◽  
Grain Growth ◽  
Precipitation Hardening ◽  
Al Alloys ◽  
Abnormal Grain Growth ◽  
Post Weld Heat Treatment ◽  
Welding Parameters ◽  
Friction Stir

Friction stir welding (FSW) is an alternative method to join aluminum (Al) alloys in a solid-state condition. However, the coarsening or dissolution of precipitation hardening phases in the welding zone causes strength reduction or softening behavior in the welded area of age-hardened Al alloys. Therefore, this research aimed to improve the mechanical properties of an FSW Al–Mg–Si alloy via post-weld heat treatment (PWHT) and the possibility of controlling the abnormal grain growth (AGG) using different welding parameters. FSW was performed with different rotational and travel speeds, and T6 heat treatment was carried out on the FSW samples as the PWHT. The results showed a decrease in the strength of the FSW samples compared with that of the base material (BM) due to the dissolution of precipitation hardening particles in the heat-affected zone. However, the emergence of AGG in the microstructure after the T6-PWHT was identified as the potential event in the microstructure of the PWHT samples. It is found that the AGG of the microstructure in similar joints of Al6061(T6) was governed by the welding parameters. The results proved that PWHT was able to increase the tensile properties of the welded samples to values comparable to that of Al6061(T6)-BM. The increased mechanical properties of the FSW joints were attributed to a proper PWHT that resulted in a homogeneous distribution of the precipitation hardening phases in the welding zones.

Fabrication and characterization of friction stir processed Al 6061 reinforced with TiB2-Al2O3

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ch. Mohana Rao ◽  
K. Mallikarjuna Rao
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Process Parameters ◽  
Friction Stir Processing ◽  
Practical Implication ◽  
Research Work ◽  
Influence Of Process Parameters ◽  
Volume Percentage ◽  
Content Type ◽  
Friction Stir

PurposeThe objective of the paper is to evaluate the fabrication process and to study the influence of process parameters of friction stir processing of 6061-TiB2-Al2O3 Aluminum alloy surface composite on microhardness tensile strength, and microstructure.Design/methodology/approachFriction stir processing method is used for attaining the desired mechanical properties, and selectively processed reinforcements to fabricate the samples. The Taguchi technique was used to optimize rotational speed, travel speed and volume percentage of reinforcement particles to enhance the mechanical properties of 6061-TiB2-Al2O3 Aluminum alloy composite.FindingsThe fabrication of surface composites through FSP allows new inventions in terms of material with enhanced surface layers without changing the base metal.Practical implicationsTo examine the behavior of the surface of the composites in the different zones, the practical implication consists of the use of different characterization techniques like optical microscopy and scanning microscopy for microstructural behavior and the measurement of hardness and tensile tests for mechanical behavior.Originality/valueThe research work consists of tool design and process parameters, which can affect the final product (microstructural changes), and the performance of the modified surface layer behavior was studied and presented.

Sign in / Sign up

Export Citation Format

Share Document